Experimental study on filtration and continuous regeneration of a particulate filter system for heavy-duty diesel engines

This study investigated the filtration and continuous regeneration of a particulate filter system on an engine test bench, consisting of a diesel oxidation catalyst（DOC） and a catalyzed diesel particulate filter（CDPF）. Both the DOC and the CDPF led to a high conversion of NO to NO2 for continuous regeneration. The filtration efficiency on solid particle number（SPN） was close to100%. The post-CDPF particles were mainly in accumulation mode. The downstream SPN was sensitively influenced by the variation of the soot loading. This phenomenon provides a method for determining the balance point temperature by measuring the trend of SPN concentration.     

Unregulated emissions from diesel engine with particulate filter using Fe-based fuel borne catalyst

The alteration and formation of toxic compounds and potential changes in the toxicity of emissions when using after-treatment technologies have gained wide attention. Volatile organic compound（VOC）, carbonyl compound and particle-phase polycyclic aromatic hydrocarbon（PAH） emissions were tested at European Steady State Cycle（ESC） to study unregulated emissions from a diesel engine with a fuel-borne catalyst and diesel particulate filter（FBC–DPF）. An Fe-based fuel-borne catalyst was used for this study. According to the results, brake specific emissions of total VOCs without and with DPF were 4.7 and4.9 mg/kWh, respectively, showing a 4.3% increase. Benzene and n-undecane emissions increased and toluene emission decreased, while other individual VOC emissions basically had no change. When retrofitted with the FBC–DPF, total carbonyl compound emission decreased 15.7%, from 25.8 to 21.8 mg/kWh. The two highest carbonyls, formaldehyde and acetaldehyde, were reduced from 20.0 and 3.7 to 16.5 and 3.3 mg/kWh respectively. The specific reactivity（SR） with DPF was reduced from 6.68 to 6.64 mg/kWh. Total particle-phase PAH emissions decreased 66.4% with DPF compared to that without DPF. However, the Benzo[a]pyrene equivalent（BaPeq） with DPF had increased from 0.016 to 0.030 mg/kWh.Fluoranthene and Pyrene had the greatest decrease, 91.1% and 88.4% respectively. The increase of two- and three-ring PAHs with DPF indicates that the fuel-borne catalyst caused some gas-phase PAHs to adsorb on particles. The results of this study expand the knowledge of the effects of using a particulate filter and a Fe-based fuel-borne catalyst on diesel engine unregulated emissions.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

V2O5/TiO2催化剂脱除NO的研究

采用了等体积浸渍法制备二氧化钛负载钒氧化物催化剂（V2O5/TiO2）,研究了V2O5负载量、反应温度、烟气流量、氨氮比以及运行时间各因素对NH3选择性催化还原NO反应（SCR）效率的影响.研究结果表明：经过500℃温度下煅烧,烟气流量为200ml/min,负载量为7wt％的V2O5/TiO2催化剂,在400℃温度下反应,NO脱除率可达70.5％.     

负载型Mn-Co/TiO2催化剂的制备及其低温NH3选择催化还原NO

采用浸渍法制备了一系列以成型TiO2为载体的Mn-Co/TiO2低温SCR催化剂,研究分析了活性组分担载量、Mn含量、焙烧温度、焙烧时间等制备参数和进口NO浓度、空速、O2体积分数、NH3/N2摩尔比等操作条件对催化剂脱硝反应活性的影响.结果表明:活性组分担载量为30%,Mn/(Mn+Co)摩尔比为80%,在500℃下焙烧6 h得到的Mn-Co/TiO2催化剂具有较高的NO转化率;在进口NO浓度为600×10-6、O2体积分数6%、空速10000 h-1、150℃条件下,NO脱除率接近100%.     

浅析废烟气脱硝催化剂环境管理

随着"十二五"期间国家对氮氧化物排放的控制越来越严格,选择性催化还原(SCR)烟气脱硝技术被广泛应用于火电厂的脱硝工程。本文介绍我国目前废烟气脱硝催化剂的产生情况、存在的环境风险以及发达国家的管理经验,从而提出我国将废烟气脱硝催化剂纳入危险废物管理,推行危险废物经营许可证制度,加强产生和经营单位的日常监督管理,从而促进行业的健康可持续发展。     

DOC/CCRT老化对柴油公交车气态物排放特性的影响

基于重型底盘测功机,研究新鲜及老化氧化型催化器(DOC)、氧化型催化器耦合催化型颗粒捕集器(DOC+CDPF,CCRT)对在用国Ⅲ柴油公交车进行中国典型城市公交车循环CCBC时一氧化碳(CO)、总碳氢化合物(THC)、一氧化氮(NO)、二氧化氮(NO_2)和氮氧化物(NO_x)、二氧化碳(CO_2)等气态物排放特性的影响.结果表明:采用新鲜及老化DOC/CCRT,均可以降低CO、THC、NO排放,增加NO_2排放,NO_x及CO_2排放基本不变;在怠速、加速、减速及匀速这4种工况下,新鲜DOC比老化DOC对CO、THC氧化效率好,新鲜CCRT比老化CCRT对THC氧化效率好,但老化CCRT对CO氧化效率更好,新鲜DOC/CCRT比老化DOC/CCRT对NO减少幅度高,对NO_2增加幅度高,但对NO_x排放总量基本无影响.     

Cu-Al2O3中骨架铜类芬顿催化去除水中有机污染物

为解决传统铁基芬顿催化剂在水体通常酸碱(pH6)条件下活性低的问题,采用简单共沉淀法制备了Cu掺杂的Al_2O_3类芬顿催化剂.通过X射线衍射(XRD)、X射线光电子能谱(XPS)和紫外可见(UV-vis)吸收光谱分析表明,Cu-Al_2O_3中铜掺杂的质量分数低于4.77%时,催化剂中铜主要以Cu~(2+)和Cu~+的形式共存于Al_2O_3的骨架结构中,形成Al—O—Cu键;过量的铜掺杂会导致外骨架铜物种如铜氧化物团簇的存在.以难降解有机污染物2-氯苯酚(2-chlorophenol,2-CP)和染料罗丹明B(Rhodamine B,Rh B)为目标污染物,对Cu-Al_2O_3的类芬顿催化性能进行了详细地研究.结果表明,骨架铜物种在中性温和条件下对2-CP和Rh B显示出很高的催化去除效率和稳定性,反应2 h,Cu-Al_2O_3(Cu质量分数4.77%)对2-CP的去除率达到54%,相应的TOC去除率达到49%,而铜离子溶出浓度仅为0.025 5 mg·L-1,而Cu-Al_2O_3(Cu质量分数7.58%)由于外骨架铜的存在导致催化活性增加缓慢和稳定性下降.ESR测试结果表明,·OH和HO_2~-/O_2~-·是反应中主要的活性物种.     

Toluene removal characteristics by a superimposed wire-plate dielectric barrier discharge plasma reactor

A superimposed wire-plate dielectric barrier discharge reactor was used to remove toluene in this study. The effects of oxygen content, gas flow rate, gas initial concentration and with/without catalyst on toluene decomposition were investigated. It was found that an optimal toluene removal was achieved when the oxygen content was about 5%. Under this condition, the highest toluene removal efficiency of 80.8% was achieved when the gas concentration was 80 mg/m^3. The toluene removal efficiency decreased with the increase of the gas flow rate and the initial concentration of toluene. In addition, the ozone concentration decreased with the increase of the initial concentration of toluene. It suggested that combining DBD （dielectric barrier discharge） with Co3O4/Al2O3/foam nickel catalyst in-situ could improve the toluene removal efficiency and suppress ozone formation. Products analysis showed that the main products were CO and CO2 when oxygen was more than 5%.     

石油化工催化剂生产过程中的职业病防治及应急处理

石化企业使用了大量的催化剂,催化剂开发、生产过程复杂,有许多原料和生产工艺,存在许多潜在的安全隐患和职业病危害因素。为预防催化剂生产过程中的事故,通过分析催化剂生产过程中的职业病危害分析,提出了相应的职业病防范及应急处置措施,加强催化剂生产过程中的职业病防治和应急处置能力,创造良好的经济、生态和社会效益,有效防止催化剂生产过程中发生安全事故和职业病。