分形块体理论及其在三峡高边坡稳定分析中的应用

把分形几何与块体理论相结合，提出了分形块体理论，建立了分形块体理论赤平解析法，并将其应用于三峡永久船闸高边坡稳定性分析中。结果表明：分形块体理论符合工程实际，是分析裂隙岩体工程稳定性行之有效的可靠方法。     

岩溶地基土洞塌陷评价及处理

地下水(地表水)产生的渗透潜蚀作用、崩解作用等是土洞形成和发展的重要原因。对工程实例中的土洞,采用极限平衡法和压力拱分析法进行了稳定性判别。在土洞中充填砼,然后采用压力灌浆,灌浆所采用的水灰比为1∶1~1∶1.5,灌浆压力一般为0.15~0.30 MPa,地基处理效果好。     

浅论云南野生蕈菌资源及其利用

云南野生蕈菌物种资源十分丰富,据初步统计仅野生食用菌就有约600种,其中目前具有重要经济、开发价值的有近60种,滇南、滇中和滇北都有可重点开发的种类,这些野生食用菌是云南各族人民物质生活中依赖的重要自然资源之一,在改善膳食结构和发展经济中,起着不可忽视的作用。为有效保护和持续利用云南野生蕈菌资源,在开发该省野生食用菌资源时,应重视发展野生食用菌深加工工业,提高产品的附加值;此外,人工促繁、优良菌种的引入和利用乡土菌种选育新品种,是持续发展的重要方面。云南的毒蘑菇,特别是剧毒菌,如灰花纹鹅膏和欧氏鹅膏的资源利用潜力较大,应重视此类毒菌毒素的研究和利用。     

确定岩体斜坡滑动面抗剪强度的动态反分析方法

滑动结构面的抗剪强度在岩体滑坡的稳定性计算中是最重要的参数,也是最难以确定的。基于岩体抗剪强度是多种因素影响下的随机变量这一认识前提下,本文以西柏坡“中共中央解放军总部”旧址滑坡为例提出了确定岩体斜坡滑动面抗剪强度的动态反分析方法,并对该方法获得的抗剪强度的实用性进行了分析。结果表明,反分析方法是获得岩体斜坡滑动面抗剪强度的最经济、合理的途径。     

不同聚合度的聚磷酸铵灭火性能研究*

为考察聚磷酸铵（APP）干粉灭火剂的聚合度对其灭火性能的影响,选用3种不同聚合度的APP,结合其晶体结构、粒度分布及热性能测试,并通过粉体杯式燃烧器进行小尺寸灭火实验,对比3种样品的灭火性能及灭火机理,研究聚合度与其灭火性能的关系。热性能测试结果显示,聚合度的升高会导致APP的热稳定性下降,随着聚合度从80升至1 500,其初始分解温度从326.11 ℃降低至321.54 ℃,失重率从75.21%增加至79.66%。实验结果表明:随着APP聚合度的增加,火焰降温速率升高,最小灭火浓度（MEC）降低,灭火性能增强,当聚合度为1 500时,MEC为118.143 g/m3。聚合度的升高有助于APP在进入火场后更早、更充分地与火焰发生反应,从而使灭火性能得到提升。     

甲醇中十氯酮溶液标准样品不确定度评定

介绍了甲醇中十氯酮溶液标准样品的研制过程,该标准样品采用称量法制备,用气相色谱质谱法进行均匀性检验和稳定性检测,对不确定度来源进行了全面评估,并与国际同类标准样品进行了量值比对分析。结果表明：该溶液标准样品均匀性良好,在18个月内质量稳定,与国外同类标准样品具有量值一致性,可用于环境监测和科学研究工作。     

常温低基质厌氧氨氧化反应器启动及其稳定性

以上向流生物滤池为反应器,以实验室内氧化沟回流污泥为接种污泥,采用先培育好氧生物膜,后转为厌氧环境培育厌氧氨氧化生物膜的方式,成功实现了常温低基质浓度下厌氧氨氧化反应器的启动。控制反应器进水pH为7.50～7.80,NH4+-N为30～40 mg/L,NO2--N为35～50 mg/L,温度为20～25℃。224 d以后,反应器启动成功。在稳定运行阶段,出水亚硝氮和氨氮的平均浓度分别为1.4 mg/L和4.6 mg/L,平均去除率分别为95.3%和90.1%,去除比例为1～1.8∶1,主要集中在1.4～1.5∶1,亚硝氮和氨氮去除的容积负荷分别为104.2 mg/(L.d)和146.0 mg/(L.d)。     

内排压脚与边坡稳定性的关系

为了研究边坡角及边坡形状与边坡稳定性的关系,采用有限元软件ANSYS模拟了不同边坡角对应的稳定系数,以及不同平盘宽度和压脚高度所形成的等储备强度边坡的稳定系数。模拟中假设材料符合相关联的理想弹塑性本构关系,强度准则符合Drucker-Prager准则,用计算收敛性作为边坡稳定性的准则,用强度折减法得出边坡的稳定系数。为了形成等储备强度边坡,由下到上分步骤进行压脚。先在平面边坡最下台阶压脚,这样提高了边坡稳定系数,在边坡进入临界状态时,最下两台阶的塑性状态相同,则压脚停止;再在最下两台阶同时压脚,在边坡进入临界状态时,最下3个台阶的塑性状态相同,则压脚停止;以此类推,在最下边n个台阶同时压脚,在边坡进入临界状态时,压到与第n+1个台阶的塑性状态相同为止。结果表明,边坡总是从坡脚开始形成塑性区,在重力加载过程中,塑性区以弧形条带向坡顶扩展,形成滑带。最有效的内排压脚是从最下台阶开始形成等储备强度边坡的压脚。     

Application of a hydroxylamine nitrate stability model to plutonium purification process equipment

A mathematical model that predicts hydroxylamine nitrate (HAN) (NH₂OH·HNO₃) stability is applied to aqueous solutions containing HAN, nitric acid and plutonium that are used in plutonium purification processes. The model estimates the stability of these solutions with respect to the rapid, hazardous, autocatalytic reaction of HAN with nitric acid that generates heat and gas. It also accounts for reaction kinetics, temperature changes, gas generation rates, solution volumes and flow rates, and distribution of plutonium and nitric acid between aqueous and organic phases. The model is applied to three typical process vessels used in solvent extraction purification of plutonium – a countercurrent aqueous/organic plutonium stripping column, an oxidation column used for HAN and hydrazine destruction, and a plutonium rework tank. Both normal and off-normal process scenarios are modeled. Two of the off-normal scenarios lead to the rapid autocatalytic reaction of HAN with nitric acid where heat and gas are generated and that could lead to damage of the process equipment and/or release of hazardous plutonium solution from the vessel. In these two cases, stationary aqueous solutions containing HAN, Pu(III), and nitric acid were allowed to slowly react until conditions for the autocatalytic reaction were reached.     

Novel mesoporous microspheres of Al and Ni doped LMO spinels and their performance as cathodes in secondary lithium ion batteries

A facile, scalable, and solution-based technique is used to fabricate Al and Ni-doped (LiAl_0.1Mn_1.9O₄ and LiAl_0.1Ni_0.1Mn_1.8O₄) microspheres of lithium manganese oxide (LMO) spinels for use as reversible cathode materials for lithium ion batteries (LIBs). The spheres of the two samples exhibit different porosities. Cells with these LMO-based cathodes are then cycled between 4.5 V and 2 V to study their stabilities while simultaneously being subjected to the undesirable Jahn-Teller distortion that occurs around the ~3 V regime. The LiAl_0.1Mn_1.9O₄ (LAMO) and the LiAl_0.1Ni_0.1Mn_1.8O₄ (LANMO) cells exhibit comparable open circuit voltages (OCV) of 2.94 V and 2.97 V, respectively. During cell cycling, the LAMO cell exhibits a maximum specific capacity of 122.51 mAh g^?1 with a capacity fade of 65.35% after 75 cycles. The LiAl_0.1Ni_0.1Mn_1.8O₄ (LAMO) sample fares better and exhibits a maximum of 140.49 mAh g^?1 and a capacity drop of 52.59%. Detailed structural studies indicate that Ni doping and the greater degree of porosity of the LANMO sample to be a stabilizing factor. This is further confirmed by cyclic voltammetry (CV) and AC impedance spectra analysis.