Mitigation of eutrophication caused by wastewater discharge: A simulation-based approach

Mitigation of eutrophication, intensified by excessive nutrient load discharge in wastewaters regulated by restrictive legal requirements, remains one of today’s most important global problems. Despite implementation of the Water Framework Directive, the Urban Wastewater Directive and the HELCOM recommendations, the actual condition of surface water is still not satisfactory. In response to the above, the study presents an alternative approach for surface water protection against eutrophication based on the selection of appropriate nutrient removal technologies. An activated sludge model simulation was used to enable the identification of environmentally justified nutrient removal systems with lowest eutrophication potential of treated wastewater conditioned by bioavailable nutrient forms content. Based on the outcome of the study, the 3-stage Bardenpho system was identified as the most efficient for bioavailable phosphorus removal, while the Johannesburg system proved to have the highest efficiency for bioavailable nitrogen removal. The proposed eutrophication mitigation approach underlines the need for a reconsideration of current legal regulations which ignore nutrient bioavailability and key eutrophication limiting factors.     

容积负荷对ABR-MBR工艺反硝化除磷性能的影响

采用连续流ABR-MBR组合工艺处理生活污水,研究不同容积负荷(volume loading rate,VLR)对该工艺反硝化除磷性能的影响,获得最佳工艺参数.试验考察ABR进水容积负荷(以COD计,下同)分别为0.76、1.01、1.51和2.27 kg·(m~3·d)~(-1)时系统去碳脱氮除磷的性能,并在各ABR容积负荷条件下考察MBR容积负荷对MBR反应器硝化性能的影响.结果表明,在ABR进水容积负荷为1.51 kg·(m~3·d)~(-1)的条件下,系统A2隔室COD去除量最大,并在MBR容积负荷为0.462 kg·(m~3·d)~(-1)时,MBR反应器中实现了短程硝化,系统NH_4~+-N和TN去除率分别达到90%和72%以上,厌氧释磷量为7.41 mg·L~(-1),缺氧吸磷量达到15.42 mg·L~(-1),出水PO_4~(3-)-P浓度低于0.5 mg·L~(-1),这表明短程硝化更有利于强化ABR-MBR系统的反硝化除磷性能.     

典型城市污水中对羟基苯甲酸酯的污染特征

对羟基苯甲酸酯(parabens)作为防腐剂、防霉剂和杀菌剂等被广泛应用于食品、化妆品和药品中.近年来的研究表明,该类化合物能够在地表水体中检出,对水生生态环境存在潜在的危害.本研究于2016年秋季和冬季,对哈尔滨某典型城市污水处理厂进水进行了24 h连续采集,对6种parabens的质量浓度和4种常规水质指标进行了分析.结果表明,parabens普遍存在于城市污水中,对羟基苯甲酸甲酯、对羟基苯甲酸乙酯和对羟基苯甲酸丙酯是主要目标物,总有机碳、总溶解固体和酸碱度与parabens的浓度具有相关性;城市污水中parabens的质量浓度具有明显的日变化趋势,但是季节差异性不大.本研究结果为城市污水处理系统中parabens的深入研究和污染控制提供了重要理论依据.     

Fenton法处理竹制品废水生化出水的研究

采用Fenton法对竹制品废水生化出水的脱色和有机物去除进行了研究.在综合考虑经济性和去除效果的基础上,起始COD质量浓度为430 mg·L-1、色度为1 500倍的废水,在反应条件:t=30℃,pH为3.5,ρ(H2O2)=1 665 mg·L-1,c(Fe2+)/c(H2O2)=0.072,反应时间3 h的情况下,Fenton氧化处理后,COD和色度的去除率分别高达87.5%和94.4%.研究发现,色度的去除率要优于有机物(以COD计)的去除率,且受外界因素影响小.GC-MS分析结果表明:经过Fenton处理后,废水中的发色团和助色团基本上完全被去除.中间产物主要是脂类衍生物,副产品有1-碘十三烷和正辛基醚等.     

制革废水和印染废水的综合毒性评估及鉴别

研究采用成组生物毒性试验(发光菌急性毒性、斑马鱼幼鱼急性毒性,斑马鱼胚胎发育毒性和小球藻急性毒性),结合理化指标,通过毒性单位、平均毒性(average toxicity,Av Tx)、毒性指数(toxic print,Tx Pr)、最敏感的测试(most sensitive test,MST)和潜在毒性效应指数(potential ecotoxic effects probe,PEEP)对不同工艺阶段印染及制革废水进行毒性削减评估.结果表明PEEP能兼顾废水排放量与毒性效应,更为客观地表征了废水综合毒性,PEEP评价结果显示制革废水和印染废水的毒性削减率分别达到36.8%和23.2%.最后,以发光菌作为受试生物,采用毒性鉴别评估(toxicity identification evaluation,TIE)技术,对印染废水进行毒性鉴别.结果表明,印染废水中主要的致毒物质为非极性有机污染,其次为可滤性化合物,然后是重金属、氧化性物质以及挥发性物质.     

微气泡臭氧催化氧化-生化耦合工艺深度处理煤化工废水

采用微气泡臭氧催化氧化-生化耦合工艺对煤化工废水生化出水进行深度处理,考察耦合系统处理性能及不同臭氧投加量和进水COD量比值的影响.结果表明,微气泡臭氧催化氧化处理能够有效降解废水中难降解含氮芳香族污染物,去除部分COD并释放氨氮,显著提高废水可生化性,臭氧利用率接近100%,无需进行臭氧尾气处理;同时为生化处理提供充足溶解氧(DO),实现生化处理对COD和氨氮的进一步有效去除,生化处理无需曝气.在系统出水回流比为30%、臭氧投加量和进水COD量之比为0.44 mg·mg~(-1)的运行条件下,耦合系统处理性能较好.微气泡臭氧催化氧化处理对COD去除率为42.5%,臭氧消耗量与COD去除量比值为1.38 mg·mg~(-1),臭氧利用率为98.0%;生化处理对COD去除率为42.3%;耦合系统整体COD去除率为66.7%,最终平均出水COD浓度为91.5 mg·L~(-1),估算整体臭氧消耗量与COD去除量比值为0.68 mg·mg~(-1),具有较优的技术经济性能.     

微生物燃料电池改性阳极处理PTA废水

探讨了不同改性阳极对微生物燃料电池(microbial fuel cell,MFC)产电性能及其对MFC处理难降解废水能力的影响.以单室空气阴极为基础,利用0.1 g电气石、质量分数75%二氧化锰/埃洛石纳米管(manganese bioxide/halloysite nanotube,MnO_2/HNT)和多壁碳纳米管-羧基(multi-walled carbon nanotube-carboxyl,MWCNT-COOH)对MFC阳极进行修饰.结果表明,不同改性阳极的MFC对含精对苯二甲酸(purified terephthalic acid,PTA)废水的去除率均高于70%,且化学需氧量(chemical oxygen demand,COD)去除率在79%以上.相较于其他几种改性阳极,以MWCNT-COOH改性材料作阳极的MFC产生的最大输出电压最高,获得的最大功率密度最高,分别为529 mV和252.73 mW·m~(-2).     

高含氮印染废水强化脱氮处理组合工艺

为考察UASB-A/LO/O（缺氧/低氧/好氧）组合工艺的实际应用效果,将该工艺应用到规模为6 000 t/d的实际工程中,考察其对高含氮印染废水处理效果,同时采用微生物高通量测序对A/LO/O工艺中的微生物菌群结构进行解析.结果表明:在前处理废水进水流量为100 m3/h,染色废水进水流量为150 m3/h,同时A/LO/O工艺污泥回流比为50%左右情况下,COD_Cr、NH₃-N和TN的去除率分别达到91.6%、95.5%和73.5%;染色和前处理废水在改良UASB内均实现了高效厌氧氨化,染色废水厌氧出水中ρ（NH₃-N）/ρ（TN）保持在80%以上,前处理废水厌氧出水保持在85%以上;调节UASB运行参数可对VFAs（挥发性脂肪酸）进行有效调控,从而为后段反硝化工艺提供高品质碳源,实现高效脱氮;A/LO/O系统对COD_Cr、NH₃-N、TN有较好的去除效果,其脱氮性能主要靠变性菌门（Proteobateria）发挥作用,该系统中低氧池的微生物种类最为丰富且发生短程硝化反硝化,对污染物去除贡献最大,当低氧池△ρ（COD_Cr）/△ρ（TN）在18.6左右时,TN去除率最高,达到82%.研究显示,该组合工艺对工程中高含氮印染废水的脱氮效果良好.      

Control of aliphatic halogenated DBP precursors with multiple drinking water treatment processes: Formation potential and integrated toxicity

The comprehensive control efficiency for the formation potentials(FPs) of a range of regulated and unregulated halogenated disinfection by-products(DBPs)(including carbonaceous DBPs(C-DBPs), nitrogenous DBPs(N-DBPs), and iodinated DBPs(I-DBPs)) with the multiple drinking water treatment processes, including pre-ozonation, conventional treatment(coagulation–sedimentation, pre-sand filtration), ozone-biological activated carbon(O_3-BAC) advanced treatment, and post-sand filtration, was investigated. The potential toxic risks of DBPs by combing their FPs and toxicity values were also evaluated.The results showed that the multiple drinking water treatment processes had superior performance in removing organic/inorganic precursors and reducing the formation of a range of halogenated DBPs. Therein, ozonation significantly removed bromide and iodide,and thus reduced the formation of brominated and iodinated DBPs. The removal of organic carbon and nitrogen precursors by the conventional treatment processes was substantially improved by O_3-BAC advanced treatment, and thus prevented the formation of chlorinated C-DBPs and N-DBPs. However, BAC filtration leads to the increased formation of brominated C-DBPs and N-DBPs due to the increase of bromide/DOC and bromide/DON.After the whole multiple treatment processes, the rank order for integrated toxic risk values caused by these halogenated DBPs was haloacetonitriles(HANs)》haloacetamides(HAMs) haloacetic acids(HAAs) trihalomethanes(THMs) halonitromethanes(HNMs) 》I-DBPs(I-HAMs and I-THMs). I-DBPs failed to cause high integrated toxic risk because of their very low FPs. The significant higher integrated toxic risk value caused by HANs than other halogenated DBPs cannot be ignored.     

新型重金属絮凝剂巯基乙酰化羟甲基聚丙烯酰胺的优化制备

为提高含铜废水的处理效果及简化处理流程,以聚丙烯酰胺(PAM)、甲醛、氢氧化钠、巯基乙酸(TGA)为原料,先经羟甲基化反应制备中间产物羟甲基聚丙烯酰胺(MPAM),再通过酰胺化反应将巯基接枝到MPAM分子链上,制备出新型重金属絮凝剂巯基乙酰化羟甲基聚丙烯酰胺(MAMPAM).以水样中Cu(Ⅱ)的去除率为考察目标,采用Plackett-Burman实验、最陡爬坡实验和响应面法中CCD实验优化MAMPAM的制备条件.结果表明,MAMPAM最优制备条件为:MPAM浓度0.31%、MPAM与TGA物质的量比为1∶3.2、反应介质p H值为4.76、反应温度为25℃、反应时间为2 h,在此条件下制备的MAMPAM对Cu(Ⅱ)的去除率为95.30%,与模型的理论预测值94.47%接近,相对偏差仅为0.83%,模型合理可靠.红外分析表明MPAM分子链上成功接上了巯基.MAMPAM对不同初始浓度的含Cu(Ⅱ)水样具有很好的去除效果,Cu(Ⅱ)去除率均能达到90%以上.MAMPAM有望成为一种有效的含铜废水处理剂,具有一定的应用前景.