Production of vermifertilizer from guar gum industrial wastes by using composting earthworm <Emphasis Type="Italic">Perionyx sansibaricus</Emphasis> (Perrier)

Efforts have been made to convert the guar gum industrial waste into a value-added product, by employing a new earthworm species for vermicomposting e.g. Perionyx sansibaricus (Perrier) (Megascolecidae), under laboratory conditions. Industrial lignocellulosic waste was amended with other organic supplements (saw dust and cow dung); and three types of vermibeds were prepared: guar gum industrial waste + cow dung + saw dust in 40: 30: 30 ratio (T₁), guar gum industrial waste + cow dung + saw dust in 60: 20: 20 ratio (T_2,), and guar gum industrial waste + cow dung + saw dust in 75: 15: 10 ratio (T₃). As compared to initial concentrations, vermicomposts exhibited a decrease in organic C content (5.0–11.3%) and C:N ratio (11.1–24.4%) and an increase in total N (18.4–22.8%), available P (39.7–92.4%), and exchangeable K (9.4–19.7%) contents, after 150 days of vermicomposting. A vermicomposting coefficient (VC) was used to compare of vermicomposting with the experimental control (composting). P. sansibaricus exhibited maximum value of mean individual live weight (742.8 ± 21.1 mg), biomass gain (442.94 ± 21.8 mg), growth rate (2.95 ± 0.15 mg day⁻¹), cocoon numbers (96.0 ± 5.1) and reproduction rate (cocoons worm⁻¹ day⁻¹) (0.034 ± 0.001) in T₂ treatment. In T₃ maximum mortality (30.0 ± 4.01 %) in earthworm population was observed. Overall, T₂ vermibed appeared as an ideal substrate to manage guar gum industrial waste effectively. Vermicomposting can be proposed as a low-input basis technology to convert industrial waste into value-added biofertilizer.     

Metal capital sustaining a North American city: Iron and copper in New Haven, CT

A detailed inventory shows that an average resident of the City of New Haven depends on a per capita capital stock of 9200 kg/c of iron and 144 kg/c of copper in the city infrastructure, buildings, transportation systems, and equipment. Of the iron stock 28% is in items such as rail cars and ships in ocean trade not permanently within the city, and 22% is devoted to receiving and delivering oil fuel to the city and its surrounding communities. Copper is principally used in the distribution of electric power and in water piping within buildings. The city's 9200 kg/c of iron stock-in-use is less than the 13,000 kg/c national average due to New Haven's lack of heavy industry and relatively small number of large buildings. The 144 kg/c of copper stock-in-use is only 58% of the overall value for the United States, but is comparable to that in cities such as Stockholm, Sweden. Attainment of a level of iron and copper services with contemporary technology in less developed countries to the level enjoyed in New Haven would require consumption of the presently identified world copper resources.     

浅议工业污染源全面达标试点中的环境监测工作

本文简要介绍了中山市在国家环保总局“十五”环境规划期间做为第一批工业污染源全面达标试点城市,环境监测部门发挥出的重要职能和作用。对工业污染源全面达标验收工作做了全面而客观的总结和评估,为日后开展此项工作的兄弟单位提供了有益的经验和启示。     

The current situation of solid waste generation and its environmental contamination in China

In China, controlling environmental pollution resulting from solid waste (SW) and hazardous waste (HW) has become one of the most pressing tasks in the field of environmental engineering. It is reported that the annual generation of industrial solid waste (ISW) in China exceeded 0.6 billion tons in the 1990s, and is increasing every year. Although ISW management has been strengthened in recent years, about 40% of SW is put in uncontrolled landfill without appropriate treatment. According to statistics from the national Environmental Protection Agency, the cumulative ISW uncontrolled landfill in China had reached 6.6 billion tons by the end of 1995, occupying around 55 000 hectares of land. Although some major uncontrolled landfills were constructed, nonetheless groundwater contamination resulted from the use of low-standard liners and poor management. Furthermore, about 20 million tons of ISW was discharged into the environment illegally, and a third of this waste was discharged directly into water bodies, making ISW one of the greatest pollution sources for surface water and ground water. Environmental pollution accidents resulting from SW occur about 100 times a year in China, and environmental issues frequently arise because of ISW pollution. The practices of SW management, treatment, and disposal started relatively late in China, and for a long time the management of SW pollution has received little attention compared with water and air pollution management. China faces problems such as the insufficiency of management laws and regulations, insufficient investment, inadequate treatment and disposal technology, and a lack of qualified technicians. At present, most treatment and disposal technology cannot meet the requests for solid waste pollution control. In order to protect, restore, and improve environmental quality in China and to realize sustainable development, the safe management and disposal of solid and hazardous wastes is a pressing challenge. In recent years, much attention has been paid to SW management in China, and investment to develop management and treatment technologies has increased. In 1995, the Law for Solid Waste Pollution Protection was issued, and work on solid waste treatment and disposal began to be legally managed. SW treatment and disposal facilities have been constructed, and now operate in some large and medium-sized cities. In particular, rapid improvements have been seen in ISW recycling, collection, and disposal of municipal solid waste and regional HW management. All the figures in this paper are from 1995, and represent the situation in China in that year. Received: April 18, 2000 / Accepted: May 15, 2000     

Analysis of the role of waste minimisation clubs in reducing industrial water demand in the UK

As a result of the UK Government's waste policy, which increasingly encourages sustainable development, and the realisation that water in the UK cannot be treated as an unlimited resource, there is growing interest in reducing the demand for water by industry. A series of industrial waste minimisation clubs have been set up within the country. This paper identifies the effectiveness of these clubs in reducing the demand for water. An overview of some of the clubs show how there is a major discrepancy between potential and implemented water savings, whilst a more detailed analysis of three specific examples show how water demand and cost to the company can be reduced, with the project paying for itself within around 1 year. It appears that companies are able to reduce water consumption by approximately 30%. If this level of saving was taken up by the entire industrial sector in England and Wales, water consumption could be reduced by approximately 1500 Ml/day. This reduction would be more significant in regions of lower rainfall, for example East Anglia and Southeast England.     

城市污泥堆肥过程中气温对堆体温度影响的模拟

在静态垛堆肥过程中,气温的变化会对堆体温度造成影响,这对堆肥过程中的堆体温度控制具有重要意义．但迄今为止,对此问题仍缺乏研究．本文引入小波分析方法对气温和堆体温度数据进行去噪和压缩处理,提取出气温波动引起的堆体温度波动信号,然后对气温波动信号和堆体温度波动信号进行分周期拟合,获得一一对应的振幅和相位差．结果表明,对于强制通风静态垛堆肥,气温波动对堆体下层（75cm）的影响最大,最大值为0．186℃,最小值为0．132℃,平均值为0．159℃;对中层（50cm）的影响最小,但随着堆肥进程的持续有增大的趋势;对上层（25cm）影响的最大值为0．105℃,最小值为0．065℃,平均值为0．085℃．从相位差上看,堆体中层（50cm）的相位差始终最大,在堆肥的降温期呈现明显减小的趋势;上层（25cm）的相位差随着堆肥进程的持续有明显增大的趋势;下层（75cm）的相位差在整个堆肥进程中呈缓慢升高的趋势．通过影响强度和相位差综合分析发现,堆体上层物料和下层物料在热量散失过程中可能存在两种不同的热交换机制,即上层物料以稳态热传导和自然对流为主,而下层物料则以非稳态热对流为主．     

城市污泥好氧堆肥物料平衡计算分析

根据好氧堆肥机理和物料平衡关系研究城市污泥好氧堆肥过程,给出了污泥预处理过程中若干平衡方程,可用这几个方程计算调节剂添加量等参数,还分别建立了好氧堆肥过程中固、液、气三相平衡关系的计算方程,有助于好氧堆肥工程的设计。     

Does industrial waste taxation contribute to reduction of landfilled waste? Dynamic panel analysis considering industrial waste category in Japan

Waste taxes, such as landfill and incineration taxes, have emerged as a popular option in developed countries to promote the 3Rs (reduce, reuse, and recycle). However, few studies have examined the effectiveness of waste taxes. In addition, quite a few studies have considered both dynamic relationships among dependent variables and unobserved individual heterogeneity among the jurisdictions. If dependent variables are persistent, omitted variables cause a bias, or common characteristics exist across the jurisdictions that have introduced waste taxes, the standard fixed effects model may lead to biased estimation results and misunderstood causal relationships. In addition, most existing studies have examined waste in terms of total amounts rather than by categories. Even if significant reductions in total waste amounts are not observed, some reduction within each category may, nevertheless, become evident.Therefore, this study analyzes the effects of industrial waste taxation on quantities of waste in landfill in Japan by applying the bias-corrected least-squares dummy variable (LSDVC) estimators; the general method of moments (difference GMM); and the system GMM. In addition, the study investigates effect differences attributable to industrial waste categories and taxation types. This paper shows that industrial waste taxes in Japan have minimal, significant effects on the reduction of final disposal amounts thus far, considering dynamic relationships and waste categories.     

Life cycle analysis of a biogas-centred integrated dairy farm-greenhouse system in British Columbia

This study investigates the potential integration of a dairy farm and a greenhouse into an eco-industrial system to promote waste-to-energy and waste-to-material exchanges. Natural gas consumption is substituted by renewable biogas generated from anaerobic digestion (AD) of the dairy manure; CO₂ for plant enrichment in greenhouses is supplied by biogas combustion and the digestate (digestion residue) from digesters is used as animal bedding, plant growing media and liquid fertilizers.A life cycle analysis (LCA) was conducted to quantify the environmental impacts of the eco-industrial system in comparison to the conventional agriculture practices. The results show that the integrated system reduces non-renewable energy consumption, climate change impact, acidification, respiratory effects from organic emissions, and human toxicity by more than 40%. If the digestate surplus is treated as a waste, the integrated system shows an increase in eutrophication and respiratory effects from inorganic emissions while all the analyzed impacts are reduced if the digestate can be used for substituting chemical fertilizers.     

Process analysis of an industrial waste-to-energy plant: Theory and experiments

Thermal conversion is fundamental in an integrated waste management system due to the capability of reducing mass and volume of waste and recovering energy content from unrecyclable materials. Indeed, power generation from industrial solid wastes (ISW) is a topic of great interest for its appeal in the field of renewable energy production as well as for an increasing public concern related to its emissions. This paper is based on the process engineering and optimization analysis, commissioned to the University Campus-Biomedico of Rome by the MIDA Tecnologie Ambientali S.r.l. enterprise, ended up in the construction of an ISW thermo-conversion plant in Crotone (Southern Italy), where it is nowadays operating. The scientific approach to the process analysis is founded on a novel cascade numerical simulation of each plant section and it has been used initially in the process design step and after to simulate the performances of the industrial plant. In this paper, the plant process scheme is described together with the values of main operating parameters monitored during the experimental test runs. The thermodynamic and kinetic basics of the mathematical model for the simulation of the energy recovery and flue gas treatment sections are presented. Moreover, the simulation results, together with the implemented parameters, are given and compared to the experimental data for 10 specific plant test runs. It was found that the model is capable to predict the process performances in the energy production as well as in the gas treatment sections with high accuracy by knowing a set of measurable input variables. In the paper fundamental plant variables have been considered such as steam temperature, steam flow rate, power generated as well as temperature, flow rate and composition of the resulting flue gas; therefore, the mathematical model can be simply implemented as a reliable and efficient tool for management optimization of this kind of plants.