废印刷线路板非金属粉-木塑复合材料性能

利用废印刷线路板非金属粉、木粉和聚氯乙烯制备复合材料,研究了复合材料的物理力学性能.结果表明:添加40目(0.35 mm)粒径非金属粉的非金属粉-木塑复合材料的各项性能整体优于添加20目(0.83 mm)粒径的复合材料;随着复合材料中40目粒径非金属粉替代量的增加,复合材料冲击强度、静曲强度整体呈下降趋势,内结合强度总体呈上升趋势, m(非金属粉)∶m(木粉)为30∶20时,静曲强度和内结合强度分别为31.74 和2.10 MPa,满足相应的国家标准和行业标准;40目粒径非金属粉-木塑复合材料的静曲模量随着非金属粉和木粉比率的增加先上升后下降,在m(非金属粉)∶m(木粉)为15∶35时达到最大值(2 853 MPa);24 h吸水厚度膨胀率和24 h吸水率分别优于硬质纤维板国家标准和地板基材用纤维板行业标准要求值.      

聚合硫酸铁/高锰酸钾/二氧化氯组合工艺用于聚氯乙烯废水回收的工程化研究

采用聚合硫酸铁复配高锰酸钾混凝结合二氧化氯氧化的组合工艺成功解决了某厂聚氯乙烯生产废水回收工艺CODMn不达标问题。工程运行结果表明,当原水CODMn=30～48 mg/L,浊度=25～46 NTU时,在CFe=16.8 mg/L,CKMnO4=45 mg/L,CClO2=20 mg/L的条件下,出水CODMn<10 mg/L,浊度<0.5 NTU,达到工业循环补给水的水质要求。     

废环氧树脂/PVC复合材料的性能

将废环氧树脂与聚氯乙烯(PVC)共混,采用模压工艺制备复合材料。通过正交实验,讨论废环氧树脂添加量、硅烷偶联剂KH-550用量、模压时间3个因素对复合材料力学性能的影响大小,得到其优化条件。在正交实验所得优化条件基础之上,研究单因素对复合材料的影响,最终确定实验的最优方案。结果表明:当模压时间10 min,废环氧树脂添加量70%,硅烷偶联剂用量2份时,复合材料的力学性能达到最优,冲击强度为10.49 kJ/m2,拉伸强度为62.24 MPa。     

Investigation of thermal treatment on selective separation of post consumer plastics prior to froth flotation

Plastics have become the widely used materials because of their advantages, such as cheapness, endurance, lightness, and hygiene. However, they cause waste and soil pollution and they do not easily decompose. Many promising technologies are being investigated for separating mixed thermoplastics, but they are still uneconomical and unreliable. Depending on their surface characteristics, these plastics can be separated from each other by flotation method which is useful mineral processing technique with its low cost and simplicity.The main objective of this study is to investigate the flotation characteristics of PET and PVC and determine the effect of plasticizer reagents on efficient plastic separation. For that purpose, various parameters such as pH, plasticizer concentration, plasticizer type, conditioning temperature and thermal conditioning were investigated. As a result, PET particles were floated with 95.1% purity and 65.3% efficiency while PVC particles were obtained with 98.1% purity and 65.3% efficiency.     

Effect of additives on dechlorination of PVC by mechanochemical treatment

Polyvinyl chloride (–CH₂–CHCl–) _n (PVC) was ground with a powdered inorganic material (CaO, CaCO₃, SiO₂, Al₂O₃, or slag) in a planetary ball mill under atmospheric conditions to investigate the effect of additions on its dechlorination. The grinding causes a dehydrochlorinating reaction, forming a mixture of partially dechlorinated PVC and inorganic chloride, depending on the grinding time. The dechlorination increases as the grinding progresses, and is improved with increasing amounts of additives. The most effective additive is a mixture of CaO, SiO₂, and Al₂O₃, which has the same constituent components as blast furnace slag. CaO, a mixture of CaO, SiO₂, and blast furnace slag, are also effective, but CaCO₃ is the least effective additive tired. Received: August 3, 2000 / Accepted: September 21, 2000     

聚氯乙烯生产过程中大气污染物的产生及治理措施

通过对聚氯乙烯生产工艺的分析,说明聚氯乙烯生产过程中主要污染物氯乙烯单体的产生部位和特点,在此基础上分析其治理措施情况,最终提出高效、可行、且易操作的治理措施。     

我国聚氯乙烯(PVC)树脂行业耗汞量削减方案研究

通过对1990-2002年我国PVC树脂总产量和乙炔法生产PVC树脂产量的统计分析,以及对耗汞情况的估算,预测了2004-2014年汞的消耗量,提出了降低k值法(降低PVC树脂单位产品的耗汞量)和降低R值法(降低乙炔法产量在PVC树脂总产量中所占比例)2种削减耗汞量的方案.结果表明:若采用降低k值法,使k值由0.20 kg/t降低到0.12 kg/t,可使耗汞量减少40%;若采用降低R值法,使R值每年减少10%或5%,则8～14年后PVC树脂行业可彻底实现无汞化.最后提出4点建议.      

远程氩等离子体提高PVC生物填料挂膜性能的机理研究

采用接触角测定、电子扫描电镜（SEM）和X射线光电子能谱（XPS）研究了远程氩等离子体表面改性前后PVC填料表面结构性能的变化,以揭示远程氩等离子体提高PVC生物填料挂膜性能的机理,并对表面改性前后PVC填料进行了细菌挂膜试验.同时,利用＂远程等离子体＂场,评价了等离子体表面改性中电子、离子、自由基的贡献.结果表明,远程氩等离子体可以通过将含氧基团和含氮基团引入PVC填料表面,使其表面极性改变,提高表面润湿性能,使得填料的挂膜性能提高,从而增强了PVC填料的生物亲和性,加强了微生物的附着、固定作用.远程氩等离子体可以在一定程度上抑制电子、离子的刻蚀作用,强化自由基反应.     

PVC塑料型材老化试验与思考

本文针对PVC塑料型材老化现象,从引起PVC塑料型材老化的基本观点、人工老化试验、不同地区气候老化影响、老化导致变色的影响因素等方面进行了讨论,提出了解决PVC塑料型材老化现象意见.     

The influence of additives on the steam gasification of PVC waste

This study is concerned with the influence of additives on the steam gasification of polyvinyl chloride (PVC) waste. Three types of PVC waste, namely pipe waste, cable waste, and flooring, were tested. The presence of additives proved to have a profound effect on the carbon-to-gas conversion. Plasticizers and other organic additives caused an increase in carbon-to-gas conversion. Inorganic additives, especially calcium, caused a decrease in carbon-to-gas conversion, resulting in an overall decrease in the yield of syngas for all three types of waste. This decrease is probably caused by the deposition of Ca on the surface of the alumina bed material. In addition, calcium reacts with the HCl formed to give CaCl₂. This results in a decrease in the recovery of hydrochloric acid. Received: July 19, 2000 / Accepted: October 9, 2000