一种封闭式选煤车间的设计

近年来,随着国家对煤炭行业控制环境污染的条件越来越严格,为了更有效的治理煤场环境污染,改善煤场周边地区环境质量,根据国内已建成的大型封闭厂房的设计经验,提出一种封闭式煤炭风选车间,车间采用轻型门式钢架结构设计,常规经济柱距6m,抗风柱柱距7．5m,室内净高10m。工程长度90m,跨度35m,屋盖系统采用钢桁架结构体系,单层压型彩色钢板封闭。封闭车间同时配套通风除尘系统,有效降低煤尘量。     

Recovery of metal values from zinc solder dross

Zinc solder dross containing 14.8% Sn, 16.3% Pb, 0.41% Al and 64.5% Zn was leached with 3% H₂SO₄ at 45°C for 1 h. Zinc and aluminum went into solution, whereas lead and tin remained with the residue. Aluminum was selectively precipitated as calcium aluminum carbonate by treating the sulphate leachate with limestone at pH 4.8. Zinc sulphate solution was either evaporated to obtain zinc sulphate crystals or precipitated as basic zinc carbonate at pH 6.8. The undissolved lead and tin were leached with 5 M hot hydrochloric acid. The major part of lead chloride ( 73%) was separated by cooling the leached products down to room temperature. From the soluble fraction, tin was recovered as hydrated tin oxide by alkylation with caustic soda at pH 2.4, while the remaining lead was separated at pH 8.5 as lead hydroxide. A process flowsheet had been suggested which involved two-stage hydrometallurgical treatment. Parameters affecting the recovery efficiency of the suggested method such as temperature, time, pH and acid: solid stoichiometric ratio were investigated. Results obtained revealed that the optimum leaching conditions were achieved by using 20 ml of 3% H₂SO₄ acid/g dross for 1 h at 45°C. Recovery efficiency of the metal salts was 99.1, 99.4, 99.6 and 99.5% for Zn, Al, Pb and Sn respectively. Recovery efficiency was related to the solubility of the concerned salts under the given experimental conditions.     

从实用结果评估污水除油用浮选机的分选能力

为从生产实际使用结果比较不同浮选机的分选能力 ,提出以小型浮选试验研究得到的除油结果做为比较时的一个基础数据 ,同时考虑处理量、浮选工艺条件、水的温度等因素的影响 ,还应注意其抗冲击能力。在讨论时应注意所用含油量分析方法     

自然环境中微塑料样品的采集与分离方法

综述了自然环境中微塑料样品采集与分离方法的研究进展,介绍了水环境、土壤与沉积物、环境空气、生物体等不同介质中微塑料的采集方法、技术原理和使用条件,以及密度分离、筛选分离、滤膜过滤等分离提取和预处理方法,提出了建立统一的微塑料采样指南,开展空气中微塑料富集、采样、分离和检测标准方法研究等建议。     

废水中可溶性硫化物的形态分析

运用毛细管区带电泳间接紫外光度法，成功地分离了水中几何可溶性硫化物，并用于废水分析取得满意效果。     

印染废水的治理研究

印染废水是一种有机物含量高、色度深、生化性差、难降解的工业生产废水。对印染废水处理技术的研究现状进行了介绍．讨论了各自的作用机理及其在印染废水处理中的应用。为工程设计和生产工艺提出了一些有益的建议。在此基础上对印染废水处理的发展趋势做了分析和展望。     

基于油水分离的餐饮废水破乳化技术研究

餐饮废水中乳化油的分离处理一直是一个技术难题,文章分别采用物理机械方法和物理化学方法对餐饮废水进行了破乳化研究。通过对比试验结果和分析破乳机理,总结出各方法不同的破乳特点。结果表明,温度越高分离效果越好,但在实际应用中,保持在50～60℃即可。低功率的超声波可以促进破乳效果,但超过30W,又会使溶液发生乳化反应。小分子醇类的加量越多,破乳化作用越强;醇类单链越长,分离效果越好。加入无机盐,在一定程度上可以加快破乳化速度,但效果并不明显。     

Recovery of volatile fatty acids via membrane contactor using flat membranes: Experimental and theoretical analysis

Volatile fatty acid (VFA) separation from synthetic VFA solutions and leachate was investigated via the use of a membrane contactor. NaOH was used as a stripping solution to provide constant concentration gradient of VFAs in both sides of a membrane. Mass flux (12.23 g/m² h) and selectivity (1.599) observed for acetic acid were significantly higher than those reported in the literature and were observed at feed pH of 3.0, flow rate of 31.5 ± 0.9 mL/min, and stripping solution concentration of 1.0 N. This study revealed that the flow rate, stripping solution strength, and feed pH affect the mass transfer of VFAs through the PTFE membrane. Acetic and propionic acid separation performances observed in the present study provided a cost effective and environmental alternative due to elimination of the use of extractants.