内循环生物流化床处理丙烯酸废水的试验

介绍内循环三相生物流化床处理丙烯酸废水的中试研究。当进水ＣＯＤ为７１０—９９２ｍｇ／Ｌ时,平均去除容积负荷ＮＶ＝４．０ｋｇＣＯＤ／（ｍ３·ｄ）,污泥负荷ＮＳ＝１．６ｋｇＣＯＤ／（ｋｇＶＳＳ·ｄ）;进水ＣＯＤ为１２７７—２２７６ｍｐ／Ｌ时,ＮＶ＝６．８ｋｇＣＯＤ／（ｍ３·ｄ）,Ｎｓ＝２．８ｋｇＣＯＤ／（ｋｇＶＳＳ·ｄ）;氧利用率约１７％。同时对流化床出水进行了后处理试验,提出了丙烯酸废水的治理方案。     

粉煤灰的改性及对刚果红的吸附

分别采用沸水浸泡、酸浸、碱浸和加热的方法对粉煤灰进行改性处理,利用FTIR仪和XRD仪对改性粉煤灰的成分和官能团进行了分析,并利用改性粉煤灰对模拟刚果红废水进行脱色。实验结果表明：碱改性粉煤灰中含有大量官能团,以及NaPl型沸石类物质,能够明显提高粉煤灰对刚果红的吸附性能;与活性炭相比,碱改性粉煤灰具有更高的性价比;在初始刚果红质量浓度为20mg/L、碱改性粉煤灰加入量为50g/L的条件下,废水的脱色率可达87.52%;碱改性粉煤灰对刚果红的吸附过程遵循二级反应动力学,较好地符合Langmuir等温式和Freundlich等温式。     

中国危险废物和医疗废物焚烧处置行业二（口恶）排放水平研究

通过调研全国危险废物和医疗废物焚烧处置设施,对包含二噁英排放水平的设施按处置对象、炉型和处理量分类,并作系统分析和研究.结果表明现有危险废物焚烧设施烟气中二噁英的浓度比医疗废物低,达标率为74.19%;危险废物选用回转窑处置效果较好,达标率为66.67%;而医疗废物选用回转窑或热解炉,要综合考虑处置规模、生产成本和二英排放总量等因素;危险废物介于10~30 t·d-1和医疗废物介于10~20 t·d-1的处置设施要尤其注意二噁英的排放问题;医疗废物焚烧飞灰中二噁英的均值浓度为危险废物6倍以上,仅有16.67%满足填埋要求.二者烟气中二英的浓度分布以1,2,3,4,6,7,8-HpCDF、2,3,7,8-TCDF和OCDD为主.     

分类收集蔬菜垃圾与植物废弃物混合堆肥工艺实例研究

以分类收集的生活垃圾(主要为蔬菜垃圾)和破碎树枝为原料,采用条垛式堆肥工艺,在中试规模条件下考察了原料初始含水率、通风频率、翻堆频率、接种比例4种因素对混合堆肥效果的影响.同时,在试验的9种工况下,对温度、氧浓度、有机碳降解率、有机碳氮比(C/N)、腐殖质含量等指标进行测定.结果表明,堆肥42d时各堆体均已达到稳定化要求.经过比较肥分保持、腐殖化程度和能量投入等指标,获得的最优堆肥控制条件为:初始含水率65%,通风频率15min/60min(开/关),翻堆频率为每3d1次,产物接种比例5%.最优控制方案下的主发酵通风率仅为0.03L.min-1.kg-1(以VS计),可实现堆肥过程的低能耗,适合于我国村镇区域的应用条件.     

Effects of typical additives on the thermal stability of ammonium peroxydisulfate

Ammonium peroxydisulfate (APS), one of the most widely used inorganic peroxides in the process industries, is a thermally unstable peroxide and potent oxidizer due to the presence of peroxy bond in the molecule and is incompatible with most substances. To investigate the effect of typical additives on the thermal decomposition of APS, in this paper, diamine phosphate (DAP), monoamine phosphate (MAP), and aluminum hydroxide (AH) were selected as additives; pure APS and samples with 10 wt% and 20 wt% of additives were first tested by differential scanning calorimetry (DSC). The experiments and analysis showed that the samples with 10 wt% of additive had better thermal stability than those with 20 wt% of additive. After screening, the three groups of 10 wt% AH, 10 wt% MAP, and 20 wt% MAP additive conditions could be considered to have a better thermal stability effect on the thermal decomposition of APS. Four groups of samples were, in turn, tested by Phi-Tec II. The adiabatic results showed two discontinuous exothermic processes; 10 wt% AH promoted the weak exothermic effect in the first stage. In contrast, the three groups of additives in the main exothermic stage showed different degrees of inhibition, and the inhibiting effect was ranked as 10 wt% AH, 10 wt% MAP, and 20 wt% MAP in order. Finally, the self-accelerated decomposition temperature (SADT) was calculated under the 25 kg standard package. The adiabatic results, including SADT, were combined to render feasible recommendations for the use of additives, which provides references for the packaging and transportation of additives and their applications.     

Effects of environmental temperature on the thermal runaway of lithium-ion batteries during charging process

Lithium-ion batteries with relatively narrow operating temperature range have provoked concerns regarding the safety of LIBs. In this work, a series of experiments were conducted to explore the thermal runaway (TR) behaviors of charging batteries in a high/low temperature test chamber. The effects of charging rates (0.5 C, 1 C, 2 C, and 3 C), and ambient temperature (2 °C, 32 °C and 56 °C) are comprehensively investigated.The results indicate that the cell exhibited greater thermal hazard at the high charging rate and ambient temperature conditions. As the charging rate increased from 0.5 C to 3 C, more lithium intercalated in the anode prompt the TR triggered in advance, the TR onset temperature decreased from 297.5 °C to 264.7 °C. In addition, the charging time decreased with the elevated ambient temperature, resulting in a relatively higher TR onset temperature and lower maximum temperature, and the average TR critical time declined by 115–143 s. Finally, the TR required less heat accumulation with increasing of charging rate and ambient temperature, and the heat generation of side reaction played a substantial role that accounted for approximately 54%∼63%. These results provide an insight into the charging cell thermal runaway behaviors in complex operation environments and deliver valuable guidance for improving the safety of cell operation.     

O3-BAC深度处理工艺中细菌群落时空分布及动态变化规律

为弄清饮用水O₃-BAC深度处理工艺过程中细菌群落的时空分布和动态变化规律,本研究以我国南方某O₃-BAC深度处理工艺水厂为研究对象,采用NovaSeq6000高通量测序技术对夏季和冬季各工艺单元出水及滤砂和活性炭生物膜等细菌群落进行解析.结果表明,出厂水pH、浊度、COD_Mn、菌落总数等指标均满足《生活饮用水卫生标准》(GB5749-2006)的要求.夏季细菌群落多样性明显高于冬季,活性炭生物膜的细菌群落多样性高于滤砂生物膜;混凝沉淀、臭氧化和消毒是影响细菌群落多样性的主要工艺单元.水样和生物膜样品绝对优势菌门均为变形菌门(Proteobacteria),且主要菌门组成大体相同,但细菌群落门水平相对丰度存在一定的时空差异,属水平上差异则更为明显.此外,检测到的条件致病菌属主要包括芽孢杆菌属(Bacillus)、不动杆菌属(Acinetobacter)、假单胞菌属(Pseudomonas)和分支杆菌属(Mycobacterium),且其所占核心微生物OTUs数目不受季节性影响.水温和生物可降解溶解性有机碳(BDOC)是显...     

剩余污泥水解酸化过程中胞外聚合物的影响因素研究

为了解胞外聚合物(EPS)对污泥水解酸化处理的影响,采用批量试验研究了污泥厌氧水解酸化处理过程中EPS的变化以及温度、pH值、污泥来源、污泥浓度对其的影响.结果表明,pH值和污泥来源对EPS产率、成分有显著的影响.强酸性和强碱性条件下污泥水解过程中溶解性EPS产率是中性条件下的2倍多;强酸性条件下细胞破裂较多,DNA物质占总EPS含量的20%左右;强碱性条件多糖类物质溶出量占总EPS的80%以上.A/O工艺污泥水解酸化EPS产率最大,平均值为41.1mg/gVSS;其次为SBR、氧化沟(OD)和A2/O工艺污泥,其中OD工艺污泥水解酸化产生的EPS中糖类与蛋白质的质量比(φ)值远小于其他工艺污泥.温度由18℃升高至35℃时,溶解性EPS产率增加近50%,多糖所占比例逐渐增大.污泥浓度由2000mg/L升高至6000mg/L,EPS产率增大至38.1mg/gVSS,当污泥浓度达到8000mg/L时,EPS产率明显减少(23.1mg/gVSS).     

生物过滤饮用水深度处理:机遇与挑战

源水水质的恶化给传统的饮用水处理工艺带来了挑战.生物过滤是饮用水消毒输配之前管理、维护及增强颗粒滤料表面生物活性以去除有机和无机物的过程.由于具有高效、低成本等优点，生物过滤在饮用水深度处理工艺中逐渐得到广泛的应用.本文综述了生物过滤在饮用水处理过程中对水中溶解性有机质（消毒副产物前体物）的去除、微量污染物的削减、嗅味化合物及氨氮的去除等.此外，针对生物过滤在水深度处理过程中存在的问题，本文详细讨论了含氮消毒副产物前体物的生成、低温下生物过滤效能下降等挑战，并提出了今后需要研究的问题.     

不同类型建筑垃圾堆场大气降尘中水溶性离子污染特征

为了解建筑垃圾长期堆放产生的扬尘对大气的影响,选择北京市两个拆迁建筑垃圾堆放场,于2019年夏季、秋季进行降尘连续采样.共收集拆迁原地堆放有效降尘样品11个,异地集中堆放有效降尘样品11个,利用离子色谱法对大气降尘中水溶性离子组分及质量浓度进行分析.结果表明：阳离子中质量浓度最高的是Ca²⁺,其次是K⁺,NH₄⁺浓度最低;阴离子中质量浓度最高的是SO₄^2-,其次是Cl^-,NO₃^-最低,降尘样品呈碱性.建筑垃圾拆迁原地堆放场地Ca²⁺、Mg²⁺、SO₄^2-、Cl^-、Na⁺、NH₄⁺平均浓度高于异地集中堆放场地对应各离子浓度.拆迁原地堆放场地中Ca²⁺、SO₄^2-、Na⁺、Cl^-受局地风向影响较大,空间分布情况与风向扩散趋势大致相同;异地集中堆放场地各离子浓度高值区域分布较原地堆放远,Ca²⁺、K⁺、SO₄^2-、Cl^-、Mg²⁺这5种离子空间分布与次主导风向较为相符.同时,两个场地水溶性离子平均浓度与距建筑垃圾堆放地的距离有一定的关系,采样点在距堆放中心200 m范围之内离子平均浓度最大,总体来说,距离堆放中心近的采样点位离子浓度高于距离较远的采样点位离子浓度.