典型钢铁企业汞排放水平及排放特征研究

以某典型钢铁企业为研究对象,测定企业废气、废水、固废汞排放水平,并分析汞排放特征。研究表明,球团、烧结、高炉工艺废气排口烟尘中汞排放浓度和排放速率明显低于烟气;汞主要以气态形式排放,烧结工艺排口废气汞最高浓度分别是其他2个排口的7倍和3倍。球团、烧结、高炉、电炉四工艺环节中,烧结汞排放速率占四工艺汞排放速率总和的87%。半干法脱硫、氨法脱硫、石灰石石膏脱硫对废气中汞的去除效率分别为90.0%、78.7%和29.9%。企业废水排放未检出汞,脱硫产生固废汞含量明显高于除尘产生固废汞含量,脱硫灰汞含量是脱硫石膏的15倍。     

生活垃圾焚烧炉烟气新标准可达性分析

对《生活垃圾焚烧污染控制标准》(GB 18485—2001)和《生活垃圾焚烧污染控制标准》(GB 18485—2014)中各项指标的排放限值作比较,并探讨了二噁英、重金属、酸性气体、烟尘、碳氧化物等烟气污染物的控制措施。结合2010—2014年浙江省部分生活垃圾焚烧厂"三同时"验收废气监测数据,对排放指标的达标情况作分析,结果表明,采用"3T+E"焚烧工艺+SNCR脱硝+半干法脱酸+活性炭喷射+布袋除尘器除尘的烟气污染控制技术,可以同时满足脱氮、脱酸、除尘,以及去除重金属和二噁英的要求。     

Metal concentrations in used engine oils: Relevance to site assessments of soils

Used engine oils contain metals, which upon entering soils may pose risks to human health or the environment. In this study, previously published concentrations of 23 metals in 213 used engine oil samples from the early 1970s to the mid-1990s are statistically evaluated. Neat (100%) used engine oils were found to contain relatively high concentrations of lead, calcium, and zinc, attributable to piston blow-by of leaded gasoline, calcium salt detergent additives, and zinc-bearing anti-corrosion/anti-oxidation additives, respectively. Wear metal concentrations were lower. The lead concentration in used engine oils in the U.S. declined between the 1970s and early 1990s, potentially providing a basis to constrain the “age” of used engine oil(s) in soils. The concentrations of 23 metals in used engine oils were compared to soil risk benchmarks in 15 representative jurisdictions in the U.S., Canada, Australia, and Europe. The maximum concentrations in neat (100%) used engine oil of eight metals – Be, Co, Fe, Mn, Ni, Se, Ag, and Ti – were lower than their collective minimum benchmarks in soils for the jurisdictions surveyed, indicating their concentrations in soils could not be reasonably expected to exceed any soil benchmarks. Nine metals (As, Ba, Cd, Cr, Cu, Pb, Sn, V and Zn), but particularly arsenic, cadmium, lead, tin, and zinc, were identified as potential contaminants of concern (PCOC) for soils from locations impacted with used engine oils, owing to their higher median concentrations (i.e., 2.5, 1.4, 1038, 5.0, and 922 mg/kg in oil, respectively) relative to most soil benchmarks. Site-specific benchmarks and metal concentrations at reasonable oil in soil concentrations require consideration when developing the suite of PCOC metal analytes for conducting site assessments of soils impacted by used engine oil.     

国内降解塑料的生产现状及发展中应注意的问题

通过对几家生产企业典型降解塑料产品及产品降解性的分析 ,提出了在研究开发和推广应用降解塑料时应综合考虑生产成本及产品降解性两个重要因素。     

Hydrothermal liquefaction phase behavior of microalgae & model compounds in fused silica capillary reactor

A fused silica capillary reactor combined with a heating/cooling stage, a microscope and a digital camera were used to investigate phase behavior during the hydrothermal liquefaction of microalgae (Dunaliella tertiolecta) and model compounds, including soya protein and glycine, starch, glucose and xylose, stearic acid and palmitic acid. Bubbles were generated at 246°C and disappeared at 360°C upon heating when Dunaliella tertiolecta used as feedstocks. Moreover, liquid products were generated at 300°C upon heating and oily liquid products began to separate out at 250°C upon cooling. The phase behavior of soya protein was similar to that of the Dunaliella tertiolecta. Meanwhile, there only observed the bubbles generation during hydrothermal liquefaction of glycine. Heating the starch, glucose and xylose above 350°C generated black solids from carbonization. Stearic acid and palmitic acid only had the process of melting, dissolution, dispersion and precipitation.     

Composting of waste algae: A review

Although composting has been successfully used at pilot scale to manage waste algae removed from eutrophied water environments and the compost product applied as a fertiliser, clear guidelines are not available for full scale algae composting. The review reports on the application of composting to stabilize waste algae, which to date has mainly been macro-algae, and identifies the peculiarities of algae as a composting feedstock, these being: relatively low carbon to nitrogen (C/N) ratio, which can result in nitrogen loss as NH₃ and even N₂O; high moisture content and low porosity, which together make aeration challenging; potentially high salinity, which can have adverse consequence for composting; and potentially have high metals and toxin content, which can affect application of the product as a fertiliser. To overcome the challenges that these peculiarities impose co-compost materials can be employed.     

Mechanical and toxicological evaluation of concrete artifacts containing waste foundry sand

The creation of metal parts via casting uses molds that are generally made from sand and phenolic resin. The waste generated after the casting process is called waste foundry sand (WFS). Depending on the mold composition and the casting process, WFS can contain substances that prevent its direct emission to the environment. In Brazil, this waste is classified according to the Standard ABNT NBR 10004:2004 as a waste Class II (Non-Inert). The recycling of this waste is limited because its characteristics change significantly after use. Although the use (or reuse) of this byproduct in civil construction is a technically feasible alternative, its effects must be evaluated, especially from mechanical and environmental points of view. Thus, the objective of this study is to investigate the effect of the use of WFS in the manufacture of cement artifacts, such as masonry blocks for walls, structural masonry blocks, and paving blocks. Blocks containing different concentrations of WFS (up to 75% by weight) were produced and evaluated using compressive strength tests (35 MPa at 28 days) and toxicity tests on Daphnia magna, Allium cepa (onion root), and Eisenia foetida (earthworm). The results showed that there was not a considerable reduction in the compressive strength, with values of 35 ± 2 MPa at 28 days. The toxicity study with the material obtained from leaching did not significantly interfere with the development of D. magna and E. foetida, but the growth of the A. cepa species was reduced. The study showed that the use of this waste in the production of concrete blocks is feasible from both mechanical and environmental points of view.     

Determination of specific gravity of municipal solid waste

This investigation was conducted to evaluate experimental determination of specific gravity (G_s) of municipal solid waste (MSW). Water pycnometry, typically used for testing soils was adapted for testing MSW using a large flask with 2000 mL capacity and specimens with 100–350 g masses. Tests were conducted on manufactured waste samples prepared using US waste constituent components; fresh wastes obtained prior and subsequent to compaction at an MSW landfill; and wastes obtained from various depths at the same landfill. Factors that influence specific gravity were investigated including waste particle size, compaction, and combined decomposition and stress history. The measured average specific gravities were 1.377 and 1.530 for as-prepared/uncompacted and compacted manufactured wastes, respectively; 1.072 and 1.258 for uncompacted and compacted fresh wastes, respectively; and 2.201 for old wastes. The average organic content and degree of decomposition were 77.2% and 0%, respectively for fresh wastes and 22.8% and 88.3%, respectively for old wastes. The G_s increased with decreasing particle size, compaction, and increasing waste age. For fresh wastes, reductions in particle size and compaction caused occluded intraparticle pores to be exposed and waste particles to be deformed resulting in increases in specific gravity. For old wastes, the high G_s resulted from loss of biodegradable components that have low G_s as well as potential access to previously occluded pores and deformation of particles due to both degradation processes and applied mechanical stresses. The G_s was correlated to the degree of decomposition with a linear relationship. Unlike soils, the G_s for MSW was not unique, but varied in a landfill environment due both to physical/mechanical processes and biochemical processes. Specific gravity testing is recommended to be conducted not only using representative waste composition, but also using representative compaction, stress, and degradation states.     

Using multivariate regression modeling for sampling and predicting chemical characteristics of mixed waste in old landfills

Municipal solid waste landfills pose a threat on environment and human health, especially old landfills which lack facilities for collection and treatment of landfill gas and leachate. Consequently, missing information about emission flows prevent site-specific environmental risk assessments. To overcome this gap, the combination of waste sampling and analysis with statistical modeling is one option for estimating present and future emission potentials. Optimizing the tradeoff between investigation costs and reliable results requires knowledge about both: the number of samples to be taken and variables to be analyzed.This article aims to identify the optimized number of waste samples and variables in order to predict a larger set of variables. Therefore, we introduce a multivariate linear regression model and tested the applicability by usage of two case studies. Landfill A was used to set up and calibrate the model based on 50 waste samples and twelve variables. The calibrated model was applied to Landfill B including 36 waste samples and twelve variables with four predictor variables.The case study results are twofold: first, the reliable and accurate prediction of the twelve variables can be achieved with the knowledge of four predictor variables (Loi, EC, pH and Cl). For the second Landfill B, only ten full measurements would be needed for a reliable prediction of most response variables. The four predictor variables would exhibit comparably low analytical costs in comparison to the full set of measurements. This cost reduction could be used to increase the number of samples yielding an improved understanding of the spatial waste heterogeneity in landfills.Concluding, the future application of the developed model potentially improves the reliability of predicted emission potentials. The model could become a standard screening tool for old landfills if its applicability and reliability would be tested in additional case studies.     

Accurate sampling of PCDD/F in high temperature flue-gas using cooled sampling probes

In a laboratory-scale combustion reactor, flue-gas samples were collected at two temperatures in the post-combustion zone, 700 °C and 400 °C, using two different water-cooled sampling probes. The probes were the cooled probe described in the European Standard method EN-1948:1, referred to as the original probe, and a modified probe that contained a salt/ice mixture to assist the cooling, referred to as the sub-zero probe. To determine the efficiency of the cooling probes, internal temperature measurements were recorded at 5 cm intervals inside the probes. Flue-gas samples were analyzed for polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs). Samples collected at 700 °C using the original cooling probe showed higher concentrations of PCDD/Fs compared to samples collected using the sub-zero probe. No significant differences were observed between samples collected at 400 °C. The results indicated that artifact formation of PCDD/Fs readily occurs during flue-gas sampling at high temperatures if the cooling within the probe is insufficient, as found for the original probe at 700 °C. It was also shown that this problem could be alleviated by using probes with an enhanced cooling capacity, such as the sub-zero probe.Although this may not affect samples collected for regulatory purposes in exit gases, it is of great importance for research conducted in the high-temperature region of the post-combustion zone.