家具企业安全管理调查研究——运用行为抽样法调查分析不安全行为

为降低家具企业事故的发生概率,通过对家具企业机加工车间工人的不安全行为的观察,依据其主要表现,将工人的不安全行为分为静态和动态两类;运用行为抽样法对生产现场工人的不安全行为情况进行的抽查,并对其不安全行为进行现状评价;通过分析不安全行为发生的原因,提出相应的改进措施。     

生活垃圾焚烧炉烟气新标准可达性分析

对《生活垃圾焚烧污染控制标准》(GB 18485—2001)和《生活垃圾焚烧污染控制标准》(GB 18485—2014)中各项指标的排放限值作比较,并探讨了二噁英、重金属、酸性气体、烟尘、碳氧化物等烟气污染物的控制措施。结合2010—2014年浙江省部分生活垃圾焚烧厂"三同时"验收废气监测数据,对排放指标的达标情况作分析,结果表明,采用"3T+E"焚烧工艺+SNCR脱硝+半干法脱酸+活性炭喷射+布袋除尘器除尘的烟气污染控制技术,可以同时满足脱氮、脱酸、除尘,以及去除重金属和二噁英的要求。     

Metal concentrations in used engine oils: Relevance to site assessments of soils

Used engine oils contain metals, which upon entering soils may pose risks to human health or the environment. In this study, previously published concentrations of 23 metals in 213 used engine oil samples from the early 1970s to the mid-1990s are statistically evaluated. Neat (100%) used engine oils were found to contain relatively high concentrations of lead, calcium, and zinc, attributable to piston blow-by of leaded gasoline, calcium salt detergent additives, and zinc-bearing anti-corrosion/anti-oxidation additives, respectively. Wear metal concentrations were lower. The lead concentration in used engine oils in the U.S. declined between the 1970s and early 1990s, potentially providing a basis to constrain the “age” of used engine oil(s) in soils. The concentrations of 23 metals in used engine oils were compared to soil risk benchmarks in 15 representative jurisdictions in the U.S., Canada, Australia, and Europe. The maximum concentrations in neat (100%) used engine oil of eight metals – Be, Co, Fe, Mn, Ni, Se, Ag, and Ti – were lower than their collective minimum benchmarks in soils for the jurisdictions surveyed, indicating their concentrations in soils could not be reasonably expected to exceed any soil benchmarks. Nine metals (As, Ba, Cd, Cr, Cu, Pb, Sn, V and Zn), but particularly arsenic, cadmium, lead, tin, and zinc, were identified as potential contaminants of concern (PCOC) for soils from locations impacted with used engine oils, owing to their higher median concentrations (i.e., 2.5, 1.4, 1038, 5.0, and 922 mg/kg in oil, respectively) relative to most soil benchmarks. Site-specific benchmarks and metal concentrations at reasonable oil in soil concentrations require consideration when developing the suite of PCOC metal analytes for conducting site assessments of soils impacted by used engine oil.     

Composting of waste algae: A review

Although composting has been successfully used at pilot scale to manage waste algae removed from eutrophied water environments and the compost product applied as a fertiliser, clear guidelines are not available for full scale algae composting. The review reports on the application of composting to stabilize waste algae, which to date has mainly been macro-algae, and identifies the peculiarities of algae as a composting feedstock, these being: relatively low carbon to nitrogen (C/N) ratio, which can result in nitrogen loss as NH₃ and even N₂O; high moisture content and low porosity, which together make aeration challenging; potentially high salinity, which can have adverse consequence for composting; and potentially have high metals and toxin content, which can affect application of the product as a fertiliser. To overcome the challenges that these peculiarities impose co-compost materials can be employed.     

阿海水电站新源沟砂石加工废水处理工艺浅谈

新源沟砂石加工系统生产废水SS浓度高,采用水力旋流/加药絮凝/多级沉淀工艺处理,运行结果表明,处理出水水质满足《污水综合排放标准》（GB8978-1996）一级标准中的给定限值70mg/L,达标出水全部回用。     

Accurate sampling of PCDD/F in high temperature flue-gas using cooled sampling probes

In a laboratory-scale combustion reactor, flue-gas samples were collected at two temperatures in the post-combustion zone, 700 °C and 400 °C, using two different water-cooled sampling probes. The probes were the cooled probe described in the European Standard method EN-1948:1, referred to as the original probe, and a modified probe that contained a salt/ice mixture to assist the cooling, referred to as the sub-zero probe. To determine the efficiency of the cooling probes, internal temperature measurements were recorded at 5 cm intervals inside the probes. Flue-gas samples were analyzed for polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs). Samples collected at 700 °C using the original cooling probe showed higher concentrations of PCDD/Fs compared to samples collected using the sub-zero probe. No significant differences were observed between samples collected at 400 °C. The results indicated that artifact formation of PCDD/Fs readily occurs during flue-gas sampling at high temperatures if the cooling within the probe is insufficient, as found for the original probe at 700 °C. It was also shown that this problem could be alleviated by using probes with an enhanced cooling capacity, such as the sub-zero probe.Although this may not affect samples collected for regulatory purposes in exit gases, it is of great importance for research conducted in the high-temperature region of the post-combustion zone.     

我国废钢加工装备发展现状与展望

以绿色经济和循环经济的重大需求为背景,系统阐述了废钢加工装备的现状与发展,详细介绍了废钢加工装备的种类与用途,分析并总结了废钢加工装备的应用现状,指出了废钢加工装备以及废钢加工行业的发展方向。     

郑州园林绿化树木低温寒冻害空间分布特征研究

绿化树木是园林景观的主体部分,同样也是园林建设中的目标植物.然而,绿化植物容易受到低温寒冻害的影响,进而影响园林布局美观.基于此,该文提出郑州园林绿化树木低温寒冻害空间分布特征研究方法,统计郑州园林绿化树木类型,对各样本按照乔木层与灌木层进行分类整理,将频度、显著度、密度等作为计算树木多样性的指标,分析比较结果,根据获...     

固定源废气监测工作若干技术问题的探讨

从监测工况、测点位置、采样过程、结果计算等几方面出发，结合实际经验，对大气固定污染源的监测工作中存在的一些疑难问题进行探讨。