制备方法对铁钛复合氧化物磷吸附性能的影响:共沉淀法与机械物理混合法

为了研究制备方法对金属复合氧化物表面性质与吸附性能的影响,本文分别采用共沉淀法与机械物理混合法制备了铁钛复合氧化物CFe-Ti与MFe-Ti.采用SEM、BET、XRD与FTIR等表征技术,研究了两种铁钛复合氧化物CFe-Ti与MFe-Ti的形貌结构、比表面积、表面羟基浓度等表面特性;通过批式吸附实验,考察了其磷吸附性能.结果表明,与纯的氧化物Fe OOH及TiO_2相比,共沉淀法制备的CFe-Ti纳米颗粒更疏松,孔结构更发达,表面羟基浓度更高,CFe-Ti的最大磷吸附容量达40.6mg·g~(-1),高于纯Fe OOH(27.2 mg·g~(-1))与TiO_2(16.7 mg·g~(-1)),分别为其1.5倍和2.4倍,展示了显著的协同效应.而MFe-Ti的形貌结构和表面性质与Fe OOH及TiO_2相比变化不大,其磷最大吸附容量为22.7 mg·g~(-1),不仅明显低于CFe-Ti,且低于纯Fe OOH,表明未产生协同效应.研究也表明,磷在CFe-Ti与MFe-Ti表面的吸附性质未发生变化,均通过形成内层表面络合物而发生了化学吸附.因此,金属复合氧化物的表面性质和吸附性能与其制备方法密切相关,与机械物理混合法相比,共沉淀法是一种更为简单经济制备高效能铁钛复合氧化物磷吸附剂的方法.     

纳米TiO_2-Al_2O_3负载CuMnO_x对甲苯的催化燃烧

研究采用改进的溶胶-凝胶法制备了TiO2-Al2O3复合载体,并用浸渍法制备CuMnOX/TiO2-Al2O3催化剂,通过对甲苯废气催化燃烧的实验,分别考察了Cu-Mn负载量、Cu/Mn摩尔比、焙烧温度及载体对催化剂制备过程及催化剂活性的影响。实验结果表明:活性组分负载量25%,铜锰活性组分的配比Cu:Mn=1:2,焙烧温度500℃是浸渍法制备CuMnOX/TiO2-Al2O3催化剂较佳的工艺条件;XRD衍射图谱表明,500℃下铜锰尖晶石的存在是催化剂催化活性优良的主要原因;由复合载体制备的CuMnOX/TiO2-Al2O3催化剂比单一载体制备的CuMnOX/Al2O3催化剂具有更高的甲苯转化率,其T99比单一载体要低20℃以上。     

异养硝化-好氧反硝化菌WXZ-8的脱氮产物N_2O和N_2研究

研究了异养硝化-好氧反硝化菌WXZ-8(Bacillus cereus)的异养硝化性能,并采用GC-ECD(Gas Chromatography-Electron Capture Detector)、GC-TCD(Gas Chromatography-Thermal Conductivity Detector)方法分别测定了脱氮过程中的气体产物N2O和N2。为了改进密封反应的溶氧条件,采用纯氧密封摇瓶培养和空气密封摇瓶培养两个对照条件下进行培养。结果表明:(1)空气密封瓶实验条件下,WXZ-8产生的N2O为0.00945mg,N2为9.5005mg,分别占从水体中脱除的氮的0.047%和47.09%,另外,同化合成的氮含量占48.74%;(2)纯氧密封瓶实验条件下,WXZ-8产生的N2O为0.00463mg,N2为9.686mg,分别占从水体中脱除的氮的0.024%与49.57%,同样,同化合成的氮含量占49.23%。两组对照实验表明,WXZ-8菌是一株高效、产生低水平量N2O的性能良好的异养硝化-好氧反硝化菌,且纯氧培养条件更有利于控制N2O的逸出。     

曝气生物流化床在铝氧化废水回用处理中的应用

采用曝气生物流化床（ABFT）工艺,对某铝氧化废水进行深度处理。结果表明,ABFT工艺具有占地面积小、处理效率高、出水水质好、流程简单等优点,出水水质达到《生活杂用水水质标准》（CJ/T 48-1999）的相应要求,并取得了良好的经济和环境效益。     

Photocatalytic degradation of methyl orange over ITO/CdS/ZnO interface composite films

ITO/CdS/ZnO interface composite films were successfully prepared by subsequent electrodeposition of CdS and ZnO onto indium tin oxide (ITO) glass substrates. The obtained ITO/CdS/ZnO composite films were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), and UV-Vis spectroscopy. The photocatalytic activity of ITO/CdS/ZnO composite films were investigated using methyl orange (MO) as a model organic compound under UV light irradiation. The influence of operating parameters on MO degradation including initial concentration of MO, pH value of solution, and inorganic anion species over the composite films were examined. A blue shift of absorption threshold was observed for the ITO/CdS/ZnO film in comparison with ITO/ZnO film. ITO/CdS/ZnO composite films prepared under specific conditions showed a higher photocatalytic activity than that of ITO/ZnO films. It was also found that the photocatalytic degradation of MO on the composite filing followed pseudo-first order kinetics.     

A comparative investigation of NdSrCu_(1-x) Co_x O_(4-δ) and Sm_(1.8) Ce_(0.2) Cu_(1-x) Co_x O_(4-δ) (x:0–0.4) for NO decomposition

A series of single-phase T-structured NdSrCu 1-x Co x O 4-δ with oxygen vacancies and T -structured Sm 1.8 Ce 0.2 Cu 1-x Co x O 4-δ (x: 0–0.4) with oxygen excess were prepared using ultrasound-assisted citric acid complexing method, and characterized by means of techniques such as thermogravimetric analysis and NO temperature-programmed desorption (NO-TPD). The catalytic activities of these materials were evaluated for the decomposition of NO. It was found that the NdSrCu 1-x Co x O 4-δ catalysts were of oxygen vacancies whereas the Sm 1.8 Ce 0.2 Cu 1-x Co x O 4-δ ones possessed excessive oxygen (i.e., over-stoichiometric oxygen); with a rise in Co doping level, the oxygen vacancy density of NdSrCu 1-x Co x O 4-δ decreased while the over-stoichiometric oxygen amount of Sm 1.8 Ce 0.2 Cu 1-x Co x O 4-δ increased. The NO-TPD results revealed that NO could be activated much easier over the oxygen-deficient perovskite-like oxides than over the oxygen-excessive perovskite-like oxides, with the NdSrCuO 3.702 catalyst showing the best efficiency in activating NO molecules. Under the conditions of 1.0% NO/helium, 2800 hr -1 , and 600–900°C, the catalytic activity of NO decomposition followed the order of NdSrCuO 3.702 NdSrCu 0.8 Co 0.2 O 3.736 NdSrCu 0.6 Co 0.4 O 3.789 Sm 1.8 Ce 0.2 Cu 0.6 Co 0.4 O 4.187 Sm 1.8 Ce 0.2 Cu 0.8 Co 0.2 O 4.104 Sm 1.8 Ce 0.2 CuO 4.045 , in concord with the sequence of decreasing oxygen vacancy or oxygen excess density. Based on the results, we concluded that the higher oxygen vacancy density and the stronger Cu 3+ /Cu 2+ redox ability of NdSrCu 1-x Co x O 4-δ account for the easier activation of NO and consequently improve the catalytic activity of NO decomposition over the catalysts.     

Metal chlorides loaded on activated carbon to capture elemental mercury

Activated carbon (AC) was considered to be an effective sorbent to control mercury in combustion systems. However, its capture capacity was low and it required a high carbon-to-mercury mass ratio. AC loaded with catalyst showed a high elemental mercury (Hg0) capture capacity due to large surface area of AC and high oxidization ability of catalyst. In this study, several metal chlorides and metal oxides were used to promote the sorption capacity of AC. As a result, metal chlorides were better than metal oxides loaded on AC to remove gaseous mercury. X-ray diffractometer (XRD), thermogravimetric analyzer (TGA) and specific surface area by Brunauer- Emmett-Teller method (BET) analysis showed the main mechanisms: first, AC had an enormous surface area for loading enough MClx; second, Cl and MxOy were generated during pyrogenation of MClx; finally, there were lots of active elements such as Cl and MxOy which could react with elemental mercury and convert it to mercury oxide and mercury chloride. The HgO and HgCl2 might be released from AC’s porous structure by thermo regeneration. A catalytic chemisorption mechanism predominates the sorption process of elemental mercury. As Co and Mn were valence variable metal elements, their catalytic effect on Hg0 oxidization may accelerate both oxidation and halogenation of Hg0. The sorbents loaded with metal chlorides possessed a synergistic function of catalytic effect of valence variable metal and chlorine oxidation.     

不同水分管理方式下水稻生长季N2O排放量估算：模型验证和输入参数检验

利用2005～2007年我国稻田N₂O排放通量的田间原位测定资料和国际上其它地区稻田N₂O报道结果,对作者建立的不同水分管理方式下水稻生长季N₂O排放估算模型进行了验证. 结果表明,持续淹水稻田N₂O排放的拟合结果与其他地区淹水稻田N₂O通量值相一致. 淹水-烤田-淹水的水分管理方式下,稻田N₂O排放的拟合值接近于国际上同类研究结果. 淹水-烤田-淹水-湿润灌溉的水分管理方式下,稻田N₂O排放的估算模型对田间原位测定资料有很好的适切性. 为了检验模型输入参数的可信度,将本研究建立的有关我国水稻生产的相关资料数据库与以往研究报道结果进行了比较,结果表明,两者具有高度的一致性. 数据库资料表明,在20世纪50～70年代间,持续淹水稻田占20%～25%,大约75%～80%的稻田采用淹水-烤田-淹水的水分管理方式. 在20世纪80～90年代间,采用持续淹水,淹水-烤田-淹水和淹水-烤田-淹水-湿润灌溉水分管理方式的稻田分别约占12%～16%、 77%和7%～12%. 20世纪50年代水稻生长季平均每季总施氮量为87.49 kg·hm^-2,而90年代平均为224.64 kg·hm^-2. 其中,化学氮肥的施用量从20世纪50年代的37.4 kg·hm^-2增加到了90年代的198.8 kg·hm^-2,分别占水稻生长季氮输入总量的43%和88%. 在20世纪50～70年代间有机氮的输入量相对比较稳定,平均变幅在45.2～48.2 kg·hm^-2之间,随后逐步降低,有机肥料氮占氮输入总量的比例从20世纪50年代的52%降低到了90年代的9%. 作物残体N输入量从20世纪50年代的4.9 kg·hm^-2增加到了80年代的6.3 kg·hm^-2. 20世纪50～70年代水稻生长季氮肥施用量具明显的空间变异性,而80～90年代间其空间变异较小. 模型验证和输入参数检验的结果表明,该模型能较好地模拟我国不同水分管理方式下的稻田N₂O直接排放量.     

氧化铝负载镧去除水中F-的研究

通过固相反应合成了氧化铝负载的氧化镧吸附剂并研究了其对水中F-的吸附.结果表明.合成的材料对F-有很好的去除效果,最大吸附量达到53.4 mg·g-1;适当提高吸附温度和氧化镧负载量都能在一定范围内提高吸附量;较低的固相反应焙烧温度有利于提高去除率,随着焙烧温度的升高,吸附量从170℃焙烧的42.2 mg·g-1下降到了350℃焙烧的32.9 mg·g-1.同时,吸附剂表现出了很好的适应性,在较宽的pH范围内都能保持较高的吸附量.     

高度有序的TiO2纳米管阵列光催化性能研究

采用恒压阳极氧化法在纯钛箔表面制备TiO2纳米管阵列,利用SEM和XRD对其进行了形貌和晶型的分析和表征,并通过TiO2纳米管阵列膜对甲基橙光催化降解,探讨光照时间、甲基橙溶液的初始浓度、溶液的初始pH值和H2O2加入浓度等因素对甲基橙的脱色率影响.结果表明,H2O2加入浓度为50mg·L-1,紫外光照射2h,溶液为中性时,在30 mg·L-1的甲基橙溶液(50mL)中,甲基橙溶液的脱色率达到100%.当H2O2加入浓度进一步增大到100 mg·L-1时,光催化的效率进一步提高,紫外光照射1h,甲基橙溶液的脱色率就已经达到了100%,并未出现抑制光催化的现象.同时还研究了TiO2纳米管阵列电极的稳定性.实验结果表明,随着TiO2纳米管阵列使用次数的增加,其光催化效果略有所下降.