亚热带水库沉积物钻孔中有机质的历史记录及其环境意义

氢指数(HI)是重要的有机质评价参数,能够反映沉积有机质中脂肪大分子物质的相对含量,并用于反演水生生态系统的历史初级生产力,有助于研究藻类生产力对污染物的富集作用。为了探讨氢指数的环境指示作用,选择了亚热带的3座水库作为研究对象,采用Rock-Eval热解与生物标志物-中性糖方法相结合的研究技术,研究了沉积钻孔有机质的来源与特征;并结合210Pb和137Cs定年技术,综合运用氢指数和总糖含量对水库的初级生产力进行了重建。结果表明:中富营养的增塘和联安水库沉积有机质主要来源于浮游藻类,且受降解的程度较小,而贫营养的新丰江水库钻孔下层有机质主要是受降解作用或陆源高等植物等的影响。近年来,3个水库的HI值都有显著性的增加,且与其对应的总糖含量以及近50年来的滑动平均温度都高度的相关,说明这些水库都经历了气候变暖所引起的初级生产力增长。同时,升高的水库生产力扩大了沉积物剖面中重金属和多环芳烃的累积。     

纳米硫化镉对A549细胞的损伤研究

研究纳米硫化镉(Nano-Cd S)材料对肺癌细胞系A549的毒性及氧化损伤作用。培养A549细胞,经传代后接种于6孔板中,每孔2 m L完全培养基,接种次日进行染毒。用直径20~30 nm、长度80~100 nm的Nano-Cd S进行染毒,染毒浓度分别为0、5、10、20、40和80 mg·L~(-1)。染毒24 h后用MTT检测细胞存活率,以存活率在80%左右的浓度为后续实验染毒浓度。应用流式细胞技术,用荧光探针法检测A549细胞的活性氧(reactive oxygen species,ROS)含量,PI-Annexin-V法检测细胞凋亡情况;用试剂盒检测细胞中超氧化物岐化酶(superoxide dismutase,SOD)和过氧化氢酶(catalase,CAT)活性以及丙二醛(malondialdehyde,MDA)含量,判断细胞氧化损伤情况。不同浓度Nano-Cd S处理细胞24 h之后,细胞存活率随剂量的增加而下降,浓度为10、20、40和80μg·L~(-1)时,存活率分别为(88.71%±0.80%)、(81.93%±3.06%)、(75.23%±1.13%)和(70.66%±5.63%),且各组间差异均具有统计学意义(P0.05)。以浓度为10和20 mg·L~(-1)的Nano-Cd S染毒24 h后,胞内ROS含量和细胞凋亡率随染毒剂量的增加而增加(P0.05);浓度为10 mg·L~(-1)时,细胞凋亡率为(6.26%±0.44%)。与对照相比,各染毒组SOD和CAT活性和MDA含量升高,20 mg·L~(-1)染毒组SOD和CAT活性和MDA含量高于10 mg·L~(-1)染毒组(P0.05)。研究表明,纳米硫化镉能引起A549细胞的氧化损伤和细胞凋亡,具有明显的细胞毒性。     

复合金属氧化物Cu-Co-Al低温催化水解HCN

采用共沉淀法制备了Cu-Al、Co-Al和Cu-Co-Al复合金属氧化物催化剂,考察了3种催化剂对HCN的催化水解性能,并通过XRD、BET、XPS和H2-TPR等对催化剂的结构和性能进行表征.结果表明, Cu-Co-Al催化剂展示最高的催化活性. 反应温度200℃,反应180min后, Cu-Co-Al、Cu-Al和Co-Al催化剂对HCN的转化率分别为95%,90%,10%;NH3生成量分别为122,118,18mg/m3.低结晶度、高分散性、高比表面积的催化剂有利于低温HCN水解.适量的表面分子氧含量、较高的Cu2+和Co3+含量、较低的还原温度是Cu-Co-Al催化剂具有较高的HCN低温水解活性的主要原因.     

3DBER-S反硝化脱氮性能及其菌群特征

针对污水处理厂尾水TN去除问题,采用16S rDNA克隆文库法,探究了3DBER-S(三维电极生物膜耦合硫自养脱氮工艺)的强化脱氮机制及其菌群特征. 结果表明,I(电流)和HRT(水力停留时间)对3DEBR-S中氢自养和硫自养反硝化作用所占比例的影响较大,但对脱氮效率影响不显著. 当进水C/N〔ρ(COD_Cr)/ρ(TN)〕为1、ρ(NO₃--N)为35 mg/L、I为300 mA、HRT为4 h时,NO₃--N和TN去除率可分别稳定在80%和74%以上. 16S rDNA克隆文库结果显示,反应器中β变形菌纲为优势菌群,占47.89%〔以OUT(操作单元)计〕. 在β变形菌纲中,与具有反硝化功能的陶厄氏菌属(Thauera)相似的细菌所占比例最大,为52.94%;与可分别利用硫和氢为电子供体进行反硝化脱氮的硫杆菌属(Thiobacillus)和食酸菌属(Acidovorax)相似的细菌分别占17.65%和14.71%. 3DBER-S中存在异养联合氢自养和硫自养反硝化协同去除硝酸盐氮的作用,可为反硝化脱氮提供充足的电子供体,节约了有机碳源消耗,并保证了稳定高效的脱氮效果.      

PVC热解过程中HCl的生成及其影响因素

采用热重分析仪(TG)对聚氯乙烯(PVC)的热解特性进行研究.在不同条件下进行PVC热解制取氯化氢(HCl)实验,研究载气流量、入料量、热解时间和热解温度对氯化氢产率的影响,得出最佳热解条件;采用离子色谱(IC)、气相色谱(GC)、气质联用仪(GC-MS)对热解产物进行化学分析,揭示PVC热解制取HCl过程的反应机理.结果表明:PVC热解制取氯化氢的最佳热解条件为载气流量100mL/min、热解时间30min、入料量1.2g和热解温度400℃;PVC热解存在2个失重阶段,即260~320 ℃和390~600 ℃;随热解温度升高,焦油产率由0.95%升高到20.29%、HCl产率由25.69%升高到53.76%,而半焦产率则由54.39%下降到11.27%、气体产率变化范围为9.09%~18.97%;当热解温度低于400 ℃时,气体组分仅检测到H2、C2H4、C3H6;当热解温度高于400 ℃时,检测到的气体组分为H2、CH4、C2H4、C2H6、C3H6、C3H8;随着热解温度的升高,焦油组分中不稳定组分逐渐转化为稳定组分.PVC热解制取HCl的第1反应阶段主要是脱除HCl的链式反应,同时生成少量的苯等芳香族化合物及环烷烃等有机化合物;第2反应阶段主要为少量HCl生成、焦油的结构重整、分子重排、脱苯环和同分异构化等.     

Assessment of oxidative and UV-C treatments for inactivating bacterial biofilms from groundwater wells

Microorganisms are ubiquitous in natural environments and in water supply infrastructure including groundwater wells. Sessile-state microorganisms may build up on well surfaces as biofilms and, if excessive, cause biofouling that reduces well productivity and water quality. Conditions can be improved using biocides and other traditional well rehabilitation measures; however, biofilm regrowth is inevitable given the continuous introduction of microorganisms from the surrounding environment. Alternative and less invasive well maintenance approaches are desirable for reducing biofilm densities while also minimizing harmful disinfection-by-products. The primary objective of this research was to evaluate effectiveness of alternative treatments for inactivating microorganisms comprising biofilms. A novel approach was designed for in situ growth of biofilms on steel coupons suspended from ‘chandeliers’. After more than 100 days of in situ growth, biofilms were harvested, sampled, and baseline biofilm densities quantified through cultivation. Ultraviolet-C (UV-C) and oxidative treatments including hydrogen peroxide (H₂O₂), ozone (O₃) and mixed oxidants were then applied to the biofilms in laboratory-scale treatments. Microbial inactivation was assessed by comparing treated versus baseline biofilm densities. H₂O₂ was the most effective treatment, and decreased density below baseline by as much as 3.1 orders of magnitude. Mixed oxidants were effective for the well having a lower density biofilm, decreasing density below baseline by as much as 1.4 orders of magnitude. Disparity in the response to treatment was apparent in the wells despite their spatial proximity and common aquifer source, which suggests that microbiological communities are more heterogeneous than the natural media from which they originate.     

预处理方法对香蒲厌氧发酵联产H2-CH4效能的影响

通过厌氧发酵动力学分析、还原糖及其他代谢产物变化情况,结合香蒲微观结构解析,系统研究酸(HCl)、碱(NaOH)、酶(纤维素酶R-10)3种预处理对水生植物厌氧发酵联产H₂-CH₄的影响. 结果表明:香蒲分别经酸、碱、酶3种预处理后,厌氧发酵联产累积H₂、CH₄产量及含量均显著提高,c(HCl)、c(NaOH)均为1.0mol/L, w(纤维素酶R-10)(以底物计)为10mg/g时,预处理最佳. 其中1.0mol/L NaOH预处理香蒲效果最佳,φ(H₂)(H₂含量)达30.09%,累积产H₂量(以香蒲干质量计)达11.39mL/g;φ(CH₄)(CH₄含量)最高达67.48%,累积产CH₄量(以香蒲干质量计)达41.87mL/g;还原糖利用率达50.87%,sCOD(溶解性化学需氧量)利用率达66.17%. 纤维素酶预处理后香蒲产CH₄能力显著提高,产CH₄阶段φ(CH₄)最高为71.39%,累积产CH₄量达46.32mL/g,还原糖利用率达72.10%. 扫描电镜微观结构分析表明,碱预处理对香蒲纤维素结构破坏程度最大,可有效增加香蒲与微生物接触面积,有利于厌氧发酵联产H₂-CH₄工艺的快速启动和稳定运行.      

Thermodynamic method for the prediction of solid CO2 formation from multicomponent mixtures

The increase in GHG concentration has a direct effect on global climate conditions. Among the possible technologies to mitigate GHG emissions, CCS is being accepted to gain emission reduction. Such technology also involves cryogenic CO₂ capture processes based on CO₂ freeze-out or where the formation of solid CO₂ must be avoided. Captured CO₂ is usually transported in pipelines for the reinjection.The risk associated to the release of CO₂ is due to the changing temperatures and pressures the system may experience, which can lead to the deposition of solid CO₂ where it must be avoided. Prolonged exposure to dry ice can cause severe skin damage and its resublimation could pose a danger of hypercapnia. It is, thus, necessary to build up a tool able to predict the conditions in which CO₂ can freeze-out.A thermodynamic methodology based on cubic EoSs has been developed which is able to predict solid–liquid–vapor equilibrium of CO₂ mixtures with n-alkanes or H₂S which are usually found in equipment for acidic gas, mainly natural gas, treatment.The focus is a detailed analysis of the method performances when more than two components are present since, for such a case, literature does not provide significant modeling results.     

湿润剂溶液在硫化矿矿尘中的反向湿润行为研究

采用毛细管反向渗透湿润实验方法,研究了两种阴离子型湿润剂对两种硫化矿矿尘的反渗长度与反渗时间的关系.在实验中,环境和溶液的温度不高(20℃左右),所选的两种湿润剂对硫化矿矿尘都具有一定的改善湿润效果作用,试剂A比试剂B稍好.在反渗长度1 cm内,其反渗长度与反渗时间接近线性关系;反渗长度增大,其反渗长度与反渗时间近乎成抛物线的关系.研究结果显示,用毛细管反渗湿润法研究湿润剂对硫化矿矿尘的湿润行为时,反渗时间与反渗长度的关系基本可用Washburn方程描述;但除了方程中所含的参数外,还存在着诸多的影响因素,如几何条件、矿尘的物理化学性质、湿润剂的种类和浓度梯度等.     

催化裂化装置硫化氢腐蚀问题及防治对策

阐述了H2S对设备的腐蚀机理,具体分析了催化裂化装置MIP-CGP技术改造后硫分布的新情况,从选材、工艺防腐、表面防腐、焊接质量控制和检测技术等方面提出了防硫化氢腐蚀的对策措施.