张弦网壳结构索张拉模拟计算及试验研究

施工张拉控制是张弦网壳结构的关键技术之一,提出采用控制索原长的反分析方法追踪结构施工整个过程。首先,通过控制索在预应力状态下的张拉力求出零状态和索原长,并同时获得预应力态下所有单元的内力。在此基础上,通过控制每一级张拉索的原长,进行非线性有限元迭代计算,可求出索在分级分批施工时的控制力,并用VC＋＋6.0编制相应的计算程序。这一方法有效地避免了通用有限元需要反复试算,计算繁琐的缺点。最后,以张弦网壳结构模型为试验对象,按分级分批张拉的方式模拟结构的现场施工,并跟踪施工过程中杆件单元的应力状态。结果表明,数值模拟计算与试验值吻合较好,计算结果可靠,该方法能精确模拟结构的施工成形过程,且在整个过程中,每根索只需张拉一次,简化了施工工艺。     

Dyes adsorption using a synthetic carboxymethyl cellulose-acrylic acid adsorbent

Removal of noxious dyes is gaining public and technological attention. Herein grafting polymerization was employed to produce a novel adsorbent using acrylic acid and carboxymethyl cellulose for dye removal. Scanning electron microscopy and Fourier-transform infrared spectroscopy verified the adsorbent formed under optimized reaction conditions. The removal ratio of adsorbent to Methyl Orange, Disperse Blue 2BLN and malachite green chloride reached to 84.2%, 79.6% and 99.9%, respectively. The greater agreement between the calculated and experimental results suggested that pseudo second-order kinetic model better represents the kinetic adsorption data. Equilibrium adsorptions of dyes were better explained by the Temkin isotherm. The results implied that this new cellulose-based absorbent had the universaiity for removal of dyes through the chemical adsorption mechanism.     

金属氧化物降解六氯苯的活性比较及催化机理研究

以氧化铝(α-Al_2O_3、γ-Al_2O_3)、氧化钙(CaO)、过渡金属氧化物(Mn O_2、α-Fe_2O_3、γ-Fe_2O_3、Ni_2O_3、CuO)为催化剂,考察了催化剂种类、添加比例等因素对六氯苯(Hexachlorobenzene,HCB)降解效果和产物组分的影响.结果表明,催化效果随催化剂添加比例的提高显著增加.在反应温度为350℃,反应时间1 h,金属氧化物添加比例为100∶1的条件下,碱土金属氧化物CaO及过渡金属氧化物中的α-Fe_2O_3和Ni_2O_3降解活性较好,这3种氧化物对HCB的降解率分别达到65.5%、100.0%和100.0%,脱氯率D_1分别为54.4%、81.9%和77.5%.HCB降解有机产物分析结果显示,8种金属氧化物与HCB样品反应产物中均存在低氯代苯,在α-Fe_2O_3和Ni_2O_3的催化作用下有2~4氯代低氯苯检出,说明在降解过程中存在明显的逐级脱氯/加氢反应;与CaO反应后的产物中低氯代苯较少,经拉曼光谱定性分析,有无序碳的检出,说明除了脱氯/加氢还存在脱氯缩合反应.     

上海地区通风指数的应用研究

利用2013—2014年上海地区的风廓线资料及NCEP再分析资料,计算研究了上海地区通风指数的变化情况,并结合实际天气情况和预报经验,对常用通风指数公式进行本地化修正.通过分析修正前后的通风指数与颗粒物浓度的关系发现,修正后通风指数的时间变化特征与PM_(2.5)浓度的时间变化有显著的负相关关系,且经过修正的通风指数对于PM_(2.5)浓度变化的指示意义更强;研究其在典型污染个例中的应用情况发现,修正后的通风指数低时,对应的PM_(2.5)浓度值高,说明修正后的通风指数能较好地反映出边界层内大气对污染物的扩散和输送作用;另外,与未修正的通风指数对比发现,修正后的通风指数降低了原通风指数的数值,对污染的指示意义更强,尤其表现在上海地区受冷空气影响时,修正后的通风指数较原通风指数降低明显,能更好地反映出大气对上游地区污染物的输送作用.由此可见,经过修正后的通风指数更适用于本地化的预报服务,这也为上海地区的空气质量预报和霾预报提供了一个新的参考指标.     

氧化还原体系低温引发丙烯酸酯乳液聚合安全风险研究

以甲基丙烯酸甲酯、丙烯酸酯乙酯、丙烯酸酯丁酯为反应单体,十二烷基苯磺酸钠为乳化剂,过硫酸铵为氧化剂,亚硫酸氢钠为还原剂,在低温下进行乳液聚合。主要研究了反应单体的热稳定性及反应过程中的相关热力学参数,最后按照规定对该聚合体系进行了安全风险研究。研究结果表明,丙烯酸酯混合单体无热分解放热风险,丙烯酸酯乳液体系的绝热温升(△Tad)为49.6℃,失控体系能达到的最高温度(MTSR)为91.9℃,该体系的最终反应工艺危险度评估为1级,聚合工艺热风险低。     

Characteristics of stable biodiesel emulsion fuel with the aid of lipophilic surfactant,polyglycerol polyricinoleate (PGPR)

ABSTRACT

Biodiesel emulsion fuel is reported as one of the most feasible options capable of generating lower NOx emission than that from fossil fuels. However, oil and water in the emulsion fuel are easily separated and unstable. The aim of the present study is to consider the production and stability of biodiesel emulsion fuel by using tetraglycerin ester (CR-310), i.e., one of lipophilic surfactant, polyglycerol polyricinoleate (PGPR) and biodiesel, i.e., Waste cooking Oil Methyl Ester (WOME) produced based on waste cooking oil. The corresponding heat rate, water content, and viscosity are measured. Emphasis is placed on the effects of water content and surfactant on biodiesel emulsions. It is found that: (i) stable emulsion fuel is obtained by adding at least 2.0% of CR-310 and is maintained over 1 month, (ii) there is no effect of water content on stable emulsion fuel if CR-310 is used over 2.0%, and (iii) the viscosity of emulsion fuels is higher than that of the biodiesel fuel and is gradually increased with an increase in the water content.     

吸附—电化学法组合工艺处理废乳化液

以季铵盐改性硅藻土为吸油剂,采用吸附—电化学组合工艺处理拉丝废乳化液,优化了工艺条件。实验结果表明,在乳化液pH为5.0、吸油剂加入量为20 g/L、反应温度为25 ℃的最优条件下吸附除油15 min,然后在清液pH为8.5、阳极电流密度为4 A/dm²的最优条件下电化学反应4 h后,废水无色无味,COD为43 mg/L,ρ（NH₃-N）=0,ρ（Cu）= 1.6 mg/L,ρ（Zn）= 3.7 mg/L,浊度为1.1 NTU,达到GB 8978—1996污水综合排放标准。     

铝铁锡共聚物的合成及其特性研究

合成制备了铝铁锡共聚物,测定分析了其水解共聚合和熟化过程中的pH变化,并通过扫描电镜和混凝实验对共聚物的晶形貌像和絮凝作用进行了研究。结果表明：Sn^4 具有比Fe^3 ,Al^3 更强的水解活性,它有使共聚物的分子趋于均一的作用;铝铁锡共聚物的最佳配比为：NAl∶NFe∶NSn=5∶5∶3,最佳水解度B^*＝2．0,此共聚物具有比CPAFC更优良的絮凝性能。     

O／W型乳化液的处理

采用药剂破乳－电解破乳工艺处理Ｏ／Ｗ型乳化液，药剂破乳选用聚合硫酸铁为破乳剂，破乳时最佳ＰＨ为８，聚合硫酸铁的最佳投量为１５００ｍｇ／Ｌ，电解破乳选用铁作阳极，铝作阴极，电流密度０．８６Ａ／ｄｍ＾２，极距２５ｍｍ，电解时间３ｈ。在上述条件下，破乳效果良好，出水清澈透明，ＣＯＤ总去除率可达到９６－９７％。     

Optimization-Based Atmospheric Plume Source Identification

This work applies optimization and an Eulerian inversion approach presented by Bagtzoglou and Baun in 2005 in order to reconstruct contaminant plume time histories and to identify the likely source of atmospheric contamination using data from a real test site for the first time. Present-day distribution of an atmospheric contaminant plume as well as data points reflecting the plume history allow the reconstruction and provide the plume velocity, distribution, and probable source. The method was tested to a hypothetical case and with data from the Forest Atmosphere Transfer and Storage (FACTS) experiment in the Duke experimental forest site. In the scenarios presented herein, as well as in numerous cases tested for verification purposes, the model conserved mass, successfully located the peak of the plume, and managed to capture the motion of the plume well but underestimated the contaminant peak.