Experimental study of recycling lightweight concrete with aggregates containing expanded glass

The focus is on the issue of waste management when constructing and recycling lightweight concrete (LWC) with aggregates containing expanded glass. The paper analyses the recycling of concrete from lightweight aggregates, and on the important issue of environmental and waste management. The characteristics of recycling LWC such as density, compressive strength and thermal conductivity are investigated, and compared with normal existing concrete from lightweight aggregates. The results indicate that it is possible to recycle lightweight concrete construction waste. The described method shows great possibilities for increasing the use of construction waste materials from LWC containing expanded glass, in order to benefit from better use of the available capacity from existing construction waste. The characteristics of density, compressive strength and thermal conductivity from the new recycled material were compared with normal existing concrete from lightweight aggregates, such as changes in dependency on the type and parts of waste as well as its new binding components. Thus, a new recycled material has been created with new characteristics of density, compressive strength and thermal conductivity, which is conform to the compressive strength class and rules on heat protection and energy efficiency use in buildings (SI OJ RS No. 42/2002). Laboratory density, compressive strength, and thermal conductivity tests results showed that LWC can be produced by the use of waste LWC with aggregates containing expanded glass. However, the use of waste LWC with aggregates containing expanded glass seems to be necessary for the production of cheaper and environmentally friendly LWC.     

废水中甲基橙的电化学降解

以FTO导电玻璃作为阳极、石墨电极作为阴极电解模拟甲基橙废水,优化了工艺条件,并对甲基橙的降解机理进行了初步探究。实验结果表明,在NaCl投加量5 g/L、电压8 V、废水pH 6、初始甲基橙质量浓度6.0 mg/L的优化条件下电解30 min,废水的脱色率达91.3%,COD降低了62%。机理研究结果表明,电解产生的羟基自由基与甲基橙发生氧化还原反应,破坏了甲基橙的显色基团,使其内部某些化学键发生断裂,从而达到脱色的目的。     

椰壳活性炭吸附消除VOCs

对一种椰壳活性炭对甲基丙烯酸甲酯的吸附消除行为进行了研究,重点考察了甲基丙烯酸甲酯的浓度、流速和吸附温度等条件以及水汽存在时对活性炭吸附行为的影响。结果表明,该颗粒活性炭对甲基丙烯酸甲酯有良好的吸附效果,甲基丙烯酸甲酯进口浓度和进气量的改变均会影响吸附饱和时间,导致其增加或减少。通过变温吸附实验确定降低环境温度对其吸附有促进作用。湿度为50%时吸附量相对干气饱和吸附量影响较小,说明该活性炭抗水汽能力较好。经多次重复再生实验,其饱和吸附量未见明显下降。     

某钢厂烧结烟气脱硫系统滤袋失效原因分析

分析了聚苯硫醚自身特性,从而了解目前烧结烟气脱硫系统袋式除尘器中选择其作为滤料的原因。并就目前某钢厂烧结烟气脱硫系统实际发生的滤袋失效问题,通过扫描电镜、EDS能谱分析及烧失量实验对滤袋进行分析,发现材料中混入的玻璃纤维是造成其失效的主要原因,为今后实际工程中滤袋的选择提供依据,从而尽量减少不必要的损失,确保烟气脱硫项目的正常运行。     

医疗废物焚烧处理核心技术的开发及应用

国内已建成的医疗废物焚烧设施目前普遍存在进料系统不稳定、玻璃结渣和高浓度HCl气体的排放的问题。这些技术难点已成为医疗废物焚烧处置行业发展的瓶颈。本文介绍了可解决上述问题的"可调节医疗废物恒流量进料技术"、"医废焚烧防玻璃结渣技术"和"含高浓度氯化氢医废尾气处理技术"三项医疗废物焚烧处理核心技术的主要特点及技术指标与应用实例。     

利用CRT屏玻璃制备板状泡沫玻璃

以废旧阴极射线管(CRT屏)为主要原料,混合碳粉作为发泡剂,硼砂为助熔剂、稳泡剂,利用烧结法制备出的板状泡沫玻璃是一种高性能无机建筑保温材料。利用TG-DSC-MS研究分析了CRT屏玻璃的热性能与发泡剂协同作用的关系。配合料被预先压制成板块状,然后在发泡温度下进行烧成。研究了发泡剂碳粉的含量、发泡温度和发泡时间与其结构、性能的关系。研究分析表明,以废CRT屏玻璃为主要原料、碳粉为发泡剂,将混合料压制成块,烧制出板状泡沫玻璃。其较佳的发泡温度为850℃、碳粉的最佳用量范围为0.3%～0.5%,较好的发泡时间为30 min。烧制的板状泡沫玻璃的密度为0.292 g/cm3。在相同的制备条件下,随着发泡温度的升高,气泡孔径也呈现增大趋势,孔壁也逐渐变薄。随着发泡时间逐渐增加,气孔的直径迅速增大,并有形成连通孔。     

Zero-valent iron nanoparticles in treatment of acid mine water from in situ uranium leaching

Acid mine water from in situ chemical leaching of uranium (Straz pod Ralskem, Czech Republic) was treated in laboratory scale experiments by zero-valent iron nanoparticles (nZVI). For the first time, nZVI were applied for the treatment of the real acid water system containing the miscellaneous mixture of pollutants, where the various removal mechanisms occur simultaneously. Toxicity of the treated saline acid water is caused by major contaminants represented by aluminum and sulphates in a high concentration, as well as by microcontaminants like As, Be, Cd, Cr, Cu, Ni, U, V, and Zn. Laboratory batch experiments proved a significant decrease in concentrations of all the monitored pollutants due to an increase in pH and a decrease in oxidation-reduction potential related to an application of nZVI. The assumed mechanisms of contaminants removal include precipitation of cations in a lower oxidation state, precipitation caused by a simple pH increase and co-precipitation with the formed iron oxyhydroxides. The possibility to control the reaction kinetics through the nature of the surface stabilizing shell (polymer vs. FeO nanolayer) is discussed as an important practical aspect.     

Improved performance of a biomaterial-based cation exchanger for the adsorption of uranium(VI) from water and nuclear industry wastewater

The amine-modified polyhydroxyethylmethacrylate (poly(HEMA))-grafted biomaterial (tamarind fruit shell, TFS) carrying carboxyl functional groups at the chain end (PGTFS-COOH) was prepared and used as an adsorbent for the removal of uranium(VI) from water and nuclear industry wastewater. FTIR spectral analysis revealed that U(VI) ions and PGTFS-COOH formed a chelate complex. The adsorption process was relatively fast, requiring only 120 min to attain equilibrium. The adsorption kinetic data were best described by the pseudo-second-order equation. The equilibrium adsorption data were correlated with the Sips isotherm model. The maximum U(VI) ions uptake with PGTFS-COOH was estimated to be 100.79 mg/g. The complete removal of 10 mg/L U(VI) from simulated nuclear industry wastewater was achieved by 3.5 g/L PGTFS-COOH. The reusability of the adsorbent was demonstrated over 4 cycles using NaCl (1.0 M) + HCl (0.5 M) solution mixture to de-extract the U(VI). The results show that the PGTFS-COOH tested is very promising for the recovery of U(VI) from water and wastewater.     

Solar driven nitrous acid formation on building material surfaces containing titanium dioxide: A concern for air quality in urban areas?

The photoenhanced uptake of nitrogen dioxide (NO₂) to the surface of commercially available self-cleaning window glass has been studied under controlled laboratory conditions. This material is one of an array of modern building products which incorporate titanium dioxide (TiO₂) nanoparticles and are finding increasing use in populated urban areas. Amongst the principal drivers for the use of these materials is that they are thought to facilitate the irreversible removal of pollutants such as NO₂ and organic molecules from the atmosphere and thus act to remediate air quality. While it appears that TiO₂ materials do indeed remove organic molecules from built environments, in this study we show that the photoenhanced uptake of NO₂ to one example material, self-cleaning window glass, is in fact accompanied by the substantial formation (50–70%) of gaseous nitrous acid (HONO). This finding has direct and serious implications for the use of these materials in urban areas. Not only is HONO a harmful respiratory irritant, it is also readily photolysed by solar radiation leading to the formation of hydroxyl radicals (OH) together with the re-release of NO_x as NO. The net effect of subsequent OH initiated chemistry can then be the further degradation of air quality through the formation of secondary pollutants such as ozone and VOC oxidation products. In summary, we suggest that a scientifically conceived technical strategy for air quality remediation based on this technology, while widely perceived as universally beneficial, could in fact have effects precisely opposite to those intended.     

Recovery of gold by chicken egg shell membrane-conjugated chitosan beads

We have successfully prepared a bead-type adsorbent from two materials with different adsorption characteristics. Heavy metals were removed by greatly swollen egg shell membrane-conjugated chitosan beads. The egg shell membrane accumulated and removed precious metal ions from a dilute aqueous solution with a high affinity in a short contact time. Experiments suggested that chitosan beads could take up gold ions with great capacity and selectivity by conjugation with egg shell membrane. Under certain conditions, the selective removal of gold and copper in a mixture of gold and copper ions by egg shell membrane-conjugated chitosan beads was 100% and 2%, respectively. Egg shell membrane-conjugated chitosan beads can be seen as a promising material to recover gold in wastewater from various industries, such as electroplating.