Miscanthus × Giganteus straw and pellets as sustainable fuels and raw material for activated carbon

Miscanthus × Giganteus is an excellent candidate for energy cultivation. Here we report, for the first time, the results of the pyrolysis of Miscanthus × Giganteus straw or pellets both in tubular reactor (3–6 g) and in rotary kiln (10–30 g). At 400–600°C the fractions obtained from both reactors are: solid 16–25 (wt.%); liquids 25–40; water 15–20 and gases 15–50. GC-MS analyses of pyrolysis liquids reveal the occurrence of phenolic derivatives and ethanol from lignin, furanic and linear oxygenated compounds from cellulose and hemicellulose. Finally the chars produced by the pyrolysis of M×G pellets in rotary kiln present good calorific values close to 29,000 J/g. Additionally, activated carbons with a BET surface area as high as 800–900 m²/g are produced from pellets. These results indicate that chars have a good potential either for energy production, e.g. briquetting, or as adsorbents precursors.     

Recovery of different waste vegetable oils for biodiesel production: A pilot experience in Bahia State,Brazil

In Brazil, and mainly in the State of Bahia, crude vegetable oils are widely used in the preparation of food. Street stalls, restaurants and canteens make a great use of palm oil and soybean oil. There is also some use of castor oil, which is widely cultivated in the Sertão Region (within the State of Bahia), and widely applied in industry. This massive use in food preparation leads to a huge amount of waste oil of different types, which needs either to be properly disposed of, or recovered. At the Laboratorio Energia e Gas-LEN (Energy & Gas lab.) of the Universidade Federal da Bahia, a cycle of experiments were carried out to evaluate the recovery of waste oils for biodiesel production. The experiences were carried out on a laboratory scale and, in a semi-industrial pilot plant using waste oils of different qualities. In the transesterification process, applied waste vegetable oils were reacted with methanol with the support of a basic catalyst, such as NaOH or KOH. The conversion rate settled at between 81% and 85% (in weight). The most suitable molar ratio of waste oils to alcohol was 1:6, and the amount of catalyst required was 0.5% (of the weight of the incoming oil), in the case of NaOH, and 1%, in case of KOH.The quality of the biodiesel produced was tested to determine the final product quality. The parameters analyzed were the acid value, kinematic viscosity, monoglycerides, diglycerides, triglycerides, free glycerine, total glycerine, clearness; the conversion yield of the process was also evaluated.     

Optimization of biodiesel production from the waste cooking oil using response surface methodology

In this research, transesterification of the waste cooking oil has been studied. Response surface methodology (RSM) based on Box–Behnken design was used to investigate the effects of the main operating parameters, including the methanol to oil molar ratio, catalyst concentration, and reaction temperature, on the biodiesel yield. The results revealed that the catalyst concentration is the most important parameter. The maximum biodiesel yield under the optimized conditions was 99.38 wt.%. Thermogravimetric analysis (TGA) was used for the determination of biodiesel conversion and the results were compared with that of gas chromatography (GC) analysis, showing a very small difference. Furthermore, an empirical quadratic equation has been presented to show the relation between biodiesel conversion and product viscosity.     

红外法测定不同行业废水中石油类/动植物油

用红外光度法和非分散红外光度法对几种有代表性水样的石油类/动植物油进行了测定,对GB/T16488-1996标准中一些步骤的可操作性及必要性进行了分析,并提出相应建议。     

Fuel from waste tyres and particulate matter emitted from the process

The interest in obtaining alternative fuels from waste sources and at the same time diminishing the impact of waste disposal has drawn attention to scrap tyres' carbon recovery. In order to thermally degrade used tyre rubber, a laboratory pyrolysis system was developed in this work. The installation devised focused on the production of liquid pyrolysates, where shredded rubber was supplied as the feedstock and nitrogen used as the carrier gas to provide an oxygen-free atmosphere. The variables affecting the performance of the process were investigated, including target temperature, heating rate and total residence time. Characterization of the volatile matter released was conducted by means of mass spectrometry to determine the composition of products, and particulate matter analysis to ascertain the aerosol content in the gas stream. The reproducibility of experiments, the influence of the temperature and time, and differences between the vapours before condensation and the exhaust gases are discussed. This work identified that the larger hydrocarbon fragments condense to constitute the oils, whereas the lighter molecules remain as non-condensable gases. This work also identified that the total number of nano-scale particles carried by the exhaust stream varies with temperature; significant changes in the composition of products and particle content were reported at approximately 400°C. The high number of nano-scale solid particulate matter present in the exhaust gases suggests that a thorough treatment for that stream would be required to avoid human health hazards.     

Emission and Performance Characteristics of a 2 Litre Toyota Diesel Van Operating on Esterified Waste Cooking Oil and Mineral Diesel Fuel

Exhaust emission and performance characteristics were evaluated in a Toyota van, powered by a 21 indirect injection (IDI) naturally aspirated diesel engine, operating on vegetable based waste cooking oil methyl ester (WCOME).Tests were performed on a chassis dynamometer and the data were compared with previous results conducted on the same vehicle using mineral diesel fuel. The data obtained includes smoke opacity, carbon monoxide (CO), carbon dioxide (CO₂), oxygen (O₂), nitrogen dioxide (NO₂), nitric oxide (NO), sulfur dioxide (SO₂) and brake power. Engine lubricating oil samples were also taken. Results from this study indicated a difference of approximately 9% in brake power between the two fuels. WCOME developed a significant lower smoke opacity level and reduced CO, CO₂, SO₂ emissions. However, O₂, NO₂ and NO levels were higher with the vegetable oil based fuel. Power values were comparable for both fuels. Lubricating oil analysis gave little change of viscosity and wear metal concentrations after 2887km were: Silicon 35ppm, Chromium 3.3ppm, Iron 33.8ppm, Copper 14.1ppm and lead 78.6ppm.     

测定水中动植物油含量的不确定度简化评定

对红外分光光度法测定水中动植物油的不确定度来源进行了分析,构造出合理的数学模型,确定了各输入量之间的关系,量化各分量后,合成得到满意的结果。从而提出,根据被测量及其所依赖的输入量之间的关系构造数学模型,并运用不同的评定方法对各个分量进行量化,可实现对某些检测项目不确定度的简化评定。     

Experimental evaluation of the catalytic efficiency of calcium based natural and modified catalyst for biodiesel synthesis

Transesterification of a mixture of vegetable oils with methanol using metal oxide catalysts derived from snail shell (SS) for biodiesel production was investigated. The metal oxides obtained from calcined snail shells in the temperature range of 650°–950 °C and modified by loading different potassium salts were used as a catalyst in the process. The catalysts were characterized by FT-IR, XRD, SEM-EDS, XPS and TGA. Catalytic activities of developed catalysts were also tested by Hammet indicator method and ion exchange method. The best calcination conditions were observed at 850°C for 4 hours based on biodiesel yield. The KF loaded snail shell gave highest biodiesel yield of 98 ± 1% in a batch reactor with highest basicity (15.9 mmoles/g) and basic strength measured by Hammet method. The optimized reaction conditions were: reaction temperature 65°C, reaction time 3 hours, methanol to oil molar ratio 9:1 and catalyst concentration 3wt%. Leaching and reusability tests confirm the stability of the catalyst as it encounters only 3% of leaching and small changes in catalytic activity up to five runs in terms of biodiesel yield.     

溢油指示物(指标)的HPLC-FLD-GM(1,1)研究

通过对油种、风化和HPLC-FLD实验条件的模糊最大矩阵元评价,确定表征溢油指示物(指标)的HPLC-FLD-GM(1,1)的建模数据信息点.结果表明,溢油风化GM(1,1)模式的预测精度较高,可用于溢油风化预测研究.     

甾烷作为溢油指示物的模糊聚类分析研究

用模糊聚类分析对溢油指示物甾烷进行了研究，为消除进样误差的影响，以标准化相对峰高为基本数据，推算出了油种及其甾烷的动态模糊聚类分析图。结果表明，油种的动态模糊聚类分析图可以显示油种间的疏近程度；甾烷的动态模糊聚类分析图可以表征溢油指示物各甾烷的贡献率，15个甾烷是模糊聚类分析的主要因子，属较理想的溢油指示物。