钢铁企业固体废弃物资源化利用浅析

固体废物做到资源化即通过综合利用,使有利用价值的固体废物变废为宝,实现资源的再循环利用,是固体废物污染控制一直努力方向。钢铁联合企业生产过程中产生的固体废弃物量大、面广,如对其进行资源化利用不仅可获得好的效益,同时也解决了环保难题。通过借鉴国内外钢铁企业固体废弃物资源化利用成功技术,使我们在开展环境影响评价工作中对钢铁企业固废的资源化利用提出一些切实可行的控制措施。     

再悬浮过程中河流底泥PAHs的迁移与释放

利用再悬浮模拟(particle entrainment simulator,PES)装置模拟了河流底泥在受到上层扰动力后的再悬浮过程.结果表明,沉积物性质如粒径组成及PAHs含量对沉积物再悬浮过程中PAHs的释放影响显著.再悬浮过程中上覆水体总悬浮颗粒物(total suspended solids,TSS)含量与颗粒态PAHs之间存在极显著相关关系.切应力对再悬浮过程中PAHs释放的影响体现在两方面.一方面,单位体积的颗粒态PAHs随切应力增大而增大;另一方面,悬浮颗粒上PAHs的富集效应随切应力增大而减弱,是由于切应力强烈导致吸附作用弱的大颗粒进入水体.上覆水体中的PAHs总量在一段时间上升后于120 min或240min趋于稳定,而颗粒态与溶解态之间具有良好响应.高低环PAHs释放行为差异显著,由于中高环PAHs的疏水性,上覆水体中检测到的多为3~4环个体.     

胞外聚合物磷酸盐形态对生物除磷过程的影响研究

以不同DO条件下污泥龄(SRT)分别为10 d和30 d的两组实验室A/O-SBR反应器活性污泥为研究对象,探讨了胞外聚合物(EPS)磷酸盐形态对生物除磷过程的影响.结果表明,污泥絮体中的磷主要分布于EPS中,PO3-4-P和聚磷酸盐(Poly-P,包括低分子量聚磷酸盐LMW PolyP和高分子量聚磷酸盐HMW Poly-P)是EPS磷的主要形态;EPS对生物除磷的影响明显大于细菌细胞,EPS磷的厌氧降低量和好氧升高量为胞内磷变化量的2.8~6.4倍.EPS中的LMW Poly-P和HMW Poly-P含量均表现厌氧降低和好氧升高的变化规律;对于相同SRT的污泥,中DO(2.5~3.5 mg·L-1)条件较低DO(0.7~1.0 mg·L-1)条件下EPS的LMW Poly-P和HMW Poly-P有更大的厌氧降低量和好氧升高量,对应着更明显的生物除磷过程,说明EPS不仅是生物除磷过程的中转站,而且参与了生物聚磷过程.     

树脂基固态胺吸附剂室温下对低浓度CO2的吸附性能研究

以大孔甲基丙烯酸酯吸附树脂为载体,聚乙烯亚胺(PEI)为有机胺,采用液相浸渍法制备出固态胺吸附剂,并研究了其在室温下对低浓度CO2的吸附行为.同时,利用氮气吸附、热重分析和扫描电镜表征了材料的物理化学性质,并采用热重法和固定床吸附法考察了材料的CO2吸附性能.结果表明,大孔树脂担载50%PEI(质量分数)时吸附性能最佳,对纯CO2的最大吸附量为175 mg·g-1;CO2的吸附行为由扩散动力学与吸附热力学共同决定,低温有利于提高吸附容量;吸附剂对400 ppm~15%浓度的CO2都具有优异的动态吸附性能,其中对400 ppm CO2的吸附量达到86 mg·g-1,对15%CO2的吸附量达到150 mg·g-1;湿度对吸附起促进作用,相对湿度为10%时,对400 ppm CO2的吸附量提高至139mg·g-1;吸附剂具有优异的循环性能,具有直接空气捕集CO2的潜力.     

固相萃取-高效液相色谱法测定水中丙烯酰胺研究

采用固相萃取-高效液相色谱法对水中的丙烯酰胺定性、定量分析。结果显示:丙烯酰胺含量在20μg/L~400μg/L之间呈良好线性关系,回归方程Y=0.476 8X+0.845 4,相关系数R为0.997 72,检出限0.1μg/L,样品回收率在71.85%~92.28%之间,相对标准偏差为3.4%~10.9%。该方法减少了有机溶剂用量,缩短了有机溶剂暴露时间,降低污染,且能满足地表水环境质量标准(GB 3838-2002)限值要求,是水中丙烯酰胺含量准确稳定的检测方法。用该方法测定了呼和浩特市引黄入呼左岸、右岸、中浅和中深4个断面水样,均未检出丙烯酰胺。     

生活垃圾源头沥水的减量提质效应研究

针对我国生活垃圾厨余组分含量高、含水率高和热值低的特点,提出以降低厨余组分含水率为主要手段,实现生活垃圾源头减量和提质为主要目标的源头沥水和选择性分质收集模式.在苏州市两个居民小区进行了为期10个月的项目试点,监测结果显示,居民家庭采取源头沥水措施后,生活垃圾产生量减少6.47%,含水率降低2.23%,低位热值提高10.94%.生活垃圾源头沥水的减量提质效应良好,有助于提高后续焚烧及填埋处理设施运行效率和二次污染控制水平,降低运输及处理成本.     

澳门城市垃圾焚烧底灰的重金属淋溶及其遗传毒性评价

应用美国国家环境保护局推荐的毒性特性溶出程序(toxicitycharacteristicleachingprocedure,TCLP),以及ICP-MS和ICP-AES技术研究了澳门城市垃圾焚烧底灰中重金属的淋溶,并结合蚕豆根尖微核试验评价了其潜在的生态与健康风险.结果显示,该底灰淋溶出来的重金属元素:铝(Al)、锰(Mn)、钴(Co)和汞(Hg)的浓度低于0.01mg·L-1,铁(Fe)、铜(Cu)和钼(Mo)的浓度低于0.1mg·L-1,而铬(Cr)、锌(Zn)、硒(Se)、锶(Sr)、钡(Ba)和铯(Cs)的浓度在0.11mg·L-1￣2.19mg·L-1之间.需要注意的是淋溶液中铅(Pb)的浓度异常高,最高可达19.06mg·L-1,超过了美国相关标准的上限(5mg·L-1);对比不同条件下底灰中重金属的淋溶情况,表明溶解作用和淋溶液的pH值是影响其淋溶的2个重要因素.蚕豆根尖微核试验显示各淋溶液处理组根尖细胞微核率明显升高,与阴性对照组相比具有显著性差异(p<0.05),表明各淋溶液具有遗传毒性;随着淋溶液中重金属浓度的增加,蚕豆根尖细胞所表现出来的毒性效应增强,表明重金属是淋溶液具有遗传毒性的重要原因.     

微波技术在固体废弃物处理中的应用

介绍了微波加热的基本原理,综述了微波技术在工业污泥、医疗垃圾、废旧轮胎、电子垃圾以及建筑垃圾等固体废弃物处理中的应用现状,展望了微波技术在污染控制领域的应用前景.     

Pyrolysis of rice husk and sawdust for liquid fuel

The paper is focused on studying how to convert rice husk and sawdust into liquid fuel. Rice husk, sawdust and their mixture were pyrolyzed at the temperature between 420℃ and 540℃, and the main product of liquid fuel was obtained. The experimental result showed that the yield of liquid fuel heavily depended on the kind of feedstock and pyrolysis temperature. In the experiments, the maximum liquid yields for rice husk, sawdust and their mixture were 56% at 465 ℃, 61% at 490℃ and 60% at 475℃ respectively. Analysis with GC-MS and other apparatus indicated that the liquid fuel is a complicated organic compound with low caloric value and can be directly used as fuel oil without any up-grading. As a crude oil, the liquid fuel can be refined to be vehicle oil.     

Environmental forensic investigation of the air pollution from a cement manufacturing unit

Abstract

Cement manufacturing is a process that results in the emission of significant quantities of suspended particulate matter (SPM) to the ambient air. An environmental forensic investigation was carried out in the surroundings of a major cement manufacturing unit at a place called Coimbatore in the southern Indian state of Tamil Nadu. The investigation was carried out to identify the contribution of the cement manufacturing unit to the SPM concentration of the surrounding air environment. The sampling points’ selection and sample collection were done following the principles outlined in the INTERPOL Manual for Pollution Crime Forensic Investigation. On-site monitoring of the air samples was carried out using Mini Laser Aerosol Spectrometer (GRIMM, Mini-LAS Model 11R). The instrument was capable of measuring particles ranging from 0.25 to 32 µm and classifying them into 31 size channels. The test results at majority of the monitoring locations were well above the limits specified in the National Ambient Air Quality Standards of India. Microscopic studies of the dust samples were carried out for surface texture and particle shape. The spatial distribution of particles was analysed using geographic information system (GIS) for the visual identification of the extent of the pollution by keeping the cement factory as the focal point. The results from the GIS and microscopic analysis established the role of the cement factory in the particulate matter pollution of its surroundings, specifically in the areas North-West of the factory. The successfully adopted procedure can serve as a guideline for the environmental forensic investigation of similar pollution incidences.