乌鲁木齐市冬季近地逆温特点及其与可吸入颗粒物浓度的相关关系分析

总结了乌鲁木齐市冬季逆温的形成及其特点,着重分析逆温强度等与可吸入颗粒物浓度的相关关系,最终得出线性方程,并做出线性拟合图。     

高强与高性能混凝土温湿度场应力分析

针对高强与高性能混凝土易于开裂的特点,对高强高性能混凝土早期温湿度场随龄期发展的分布情况以及混凝土的收缩变形进行理论分析,建立相应的计算模型,编制三维有限元程序,分析在外界温湿度变化以及不同养护条件下由混凝土内部温差和湿度变化产生的温度应力和干燥收缩应力,从施工养护方法上探讨了高强与高性能混凝土抗裂性能的改善措施.     

锅炉蒸汽过热器爆管原因分析及整改措施

针对锅炉过热器管在运行中常见的过热爆管问题 ,从原理及运行工况的角度进行分析 ,并提出了有效的隐患整改措施 ,保证了锅炉的正常运行。     

干燥条件下高硫煤低温氧化特性研究

为进一步揭示不同环境条件下高硫煤的低温氧化特性,选取含硫量较低、自燃倾向性较高的褐煤,向其添加不同比例的FeS2,配制成含量分别为3%,5%,7%的混合高硫煤样,利用中国矿业大学自行研制的煤氧化模拟试验系统,测试分析干燥混合煤样在低温氧化过程中,交叉温度和指标气体CO产生量体积的变化。试验结果表明,在低温干燥的条件下,随着FeS2含量的增加,煤样的氧化特性受到抑制:交叉点温度升高;指标气体CO产生量在相同温度时体积降低。因此,在高硫煤层自燃火灾防治过程中,应尽量控制煤层周围环境的干燥度。     

纵向风对隧道火灾拱顶最高温度及其位置的影响

研究了燃烧风洞内不同纵向风速、不同火源功率条件下,隧道近火源区顶部温度沿纵向分布情况。结果表明,纵向风对不同尺寸火源条件下的顶部温度的影响呈不同特征。对较小尺寸火源,隧道顶部温升随风速增加而减小至稳定值;而对较大尺寸火源,顶部温升随风速增加先增加后减小。对于矩形火源,当纵向风较小(0.5~1.5m/s)时,长边平行于纵向风时顶部最高温升大于长边垂直于纵向风的情况;而当纵向风较大(≥2 m/s)时,两种油盘放置方式的顶部最高温升一致。纵向风作用下,顶部最高温升位置向下游呈现"两次移动"特征,即随着纵向风速增加该位置先向下游移动,当风速达到某一值时,隧道拱顶的加热机制由对流和辐射共同主控转变为辐射单独主控,最高温升位置突变回到上游后再次逐渐向下游移动。     

瞬态径向热流法测定松散煤体变导热系数

松散煤体的导热系数是指在单位梯度作用下,松散煤体单位时间内通过单位面积的热量,表征了松散煤体导热性能的强弱,是研究煤自燃的重要参数。目前,使用最广泛的热线法,测试结果易受电阻升温变化影响。针对当前测试方法的不足,本文在二维径向导热模型的基础上,设计了瞬态径向热流法测定松散煤体变导热系数测试装置,并建立了相应的导热系数解算模型。通过测定不同煤样随温度变化的变导热系数。结果表明,随着温度的升高,松散煤体的导热系数不断上升,两者之间基本成线性关系,测试结果符合松散煤体的导热特性。     

火灾环境中油罐罐壁冷却优化部署研究

对油罐火灾中着火罐罐壁和邻近罐罐壁的温度分布进行了科学分析,并进行了罐壁冷却实验研究,研究不同油罐罐壁材质对冷却效果的的影响,以及有热源作用和无热源作用罐壁在不同流量冷却水作用下的温度变化规律。结果表明,不同罐壁材质对冷却效果的影响不大,在实际火灾中可忽略罐壁材质的影响;流量越大,冷却速度越快,但达到火灾冷却要求时,不同大小流量冷却水的冷却效果差异并是很大,合适的供水强度是油罐高效冷却的前提。对油罐火灾冷却力量的部署提出了优化原则,为防灭火工作提供了一定的科学依据。     

Effects of EGR on performance and emissions of a diesel engine fuelled with balanites aegyptiaca/diesel blends

In this study, balanites Aegyptiaca (L.) Del biodiesel was blended in proportions of 10% and 20% on the volume basis with diesel fuel and tested in a single cylinder, VCR diesel engine under measured load conditions with varied EGR rates (0, 10 and 20%). The results showed that B10 and B20 blends shown a significant reduction rate in terms of NO_x emissions that were familiar with biodiesel blends. At peak load conditions, BTE increased slightly for test fuel blends compared with pure diesel fuel while the BSFC rate and EGT suffered from increasing and decreasing nature with respect to blending percentage. From the emissions point of view, with the increase in blends percentage, a significant reduction rate is observed in terms of CO and HC concentrations (up to 12.34 and 17.5%, respectively) while NOx emissions decreased at peak load conditions (up to 24.34%). HC and CO emissions decreased with increase in blends percentage. However, lower levels of NO_x and EGT (up to 21.37 and 8.47%, respectively) and the average increase in terms of BTE and BSFC (up to 2.83 and 2.9%, respectively) can be realised with B20 test fuel blend under 20% EGR rate.     

Alternative method to prevent thermal runaway in case of error on operating conditions continuous reactor

Thermal runaway was studied in a continuous tubular pilot reactor under steady-state regime. Different accident scenarii were conducted by making some errors on reactant concentrations and/or temperature feed. To prevent thermal runaway, control by direct contact by solvent injection was used at different reactor locations. This injection allowed controlling the maximum reaction temperature. A simplified analytical method to estimate the maximum reaction temperature along the reactor was used.Benefit of this control method was the diminution of computational time. Furthermore, by injecting solvent to control maximum reaction temperature, there is no need to shut down the unit. The control method was validated experimentally.     

Sources of underground CO: Crushing and ambient temperature oxidation of coal

As a harmful gas in underground coal mine, CO seriously threatened the safety of miners. Currently, the spontaneous combustion of residual coal in goaf is generally considered as the main source of underground CO. CO gas is also widely used as an indicator gas in fire prediction in mines. However, high concentrations of CO are also detected in some mines without spontaneous combustion of coal. Therefore, in the paper, with four ranks of coal, we studied other two potential CO sources: crushing and oxidation at ambient temperature. The more completely crushed coal produces more CO. The concentration of generated CO is inversely proportional to moisture content in coal. Therefore, the addition of water can inhibit the generation process of CO during the crushing process of coal. Lignite with low metamorphic grade can be oxidized to produce CO at ambient temperature (25 °C), and anthracite with high coal rank can be only oxidized to produce CO at 60 °C. Infrared spectra indicated that the coal with rich aliphatic hydrocarbons and oxygen-containing functional groups are more susceptible to oxidation at room temperature. Moreover, the smaller particle size of coal is more beneficial to the oxidation at ambient temperature to generate CO. CO generation during coal oxidation is also closely related to the ventilation rate.