污泥厌氧消化预处理技术综述

全球环境问题已成为国际社会关注的焦点,围绕全球气候变化,降低温室气体排放,寻求再生能源,节能减排已成为目前国际科技发展的方向。通过"十一五"污水处理厂的建设,每年污泥产量已接近3000万吨(含水率80%脱水污泥计)以上,且以每年10%的速度递增。其处理与处置是制约社会经济发展的重要问题。但是,城市污泥蕴含有大量生物质能,通过借鉴国外先进技术与经验,开发城市污泥生物质能提取和利用技术,对我国节能减排具有重要战略意义。由于细胞壁的存在,使得污泥水解成为限制厌氧消化效率的重要瓶颈,而污泥强化预处理可有效提高污泥细胞壁的破坏,溶出胞内有机物,最大化回收剩余污泥中的有机能源。目前,预处理技术较多,如超声波预处理、热处理、微波预处理、碱解处理、臭氧预处理等,本文从物理、化学等角度分析了不同预处理对厌氧消化技术的影响。     

pH对活化前后废弃铁铝泥吸附不同种磷动力学的影响

实验研究了300℃热活化前后的给水厂废弃铁铝泥（R-FARs和H300-FARs）对正磷酸盐、聚磷酸盐和有机磷酸盐的吸附动力学特性,并考察pH对不同磷吸附动力学的影响。结果表明,pH对不同磷吸附动力学过程的影响趋势相似,即低pH有利于吸附。准二级动力学模型能够更真实地反映不同磷在R-FARs和H300-FARs的吸附动力学行为,由拟合结果可知焦磷酸盐和六肌醇磷酸盐的初始吸附速率相对较大,而甘油磷酸盐最小;且活化作用明显提高了不同磷的初始吸附速率,并减弱了pH对初始吸附速率的影响。不同磷的吸附速率受到液膜扩散、颗粒内扩散和吸附反应三者共同控制,其中吸附反应是主要的控制步骤。     

太阳能污泥干化在欧洲的应用

太阳能污泥干化指的是利用太阳能为主要能源对污水处理厂污泥进行干化和稳定化的污泥处理技术。该技术运用太阳能,借助传统温室干燥工艺,具有低温干化、运行费用低廉、操作简单、运行安全稳定、干化后的污泥仍保留原有的农用价值等特点。该文主要介绍了该工艺的工作原理及流程,工艺设计参数及其与传统热干化技术相比的优缺点,并简要介绍了该工艺在欧洲市场上的商业应用。     

不同热力背景对城市降雨（暴雨）的影响（Ⅰ）—降雨分布的空间差异

如何准确描述和预测降雨（暴雨）的空间分布,已成为城市减灾防灾的重要内容,本文探讨了利用热信息研究城市降雨空间分布差异的方法。在遥感、GIS技术支持下,利用对没的期夏、冬季热图像的主成分析和图像分割,将上海市1958－1998年热环境划分为自然、低温、高温3种不同的热力背景。在此基础上,就不同热力背景对城市降雨（暴雨）分布空间差异的影响规律进行了研究,为建立城市降雨空间差异预报模型奠定了基础。     

黄岛电厂温排水对大型底栖生物群落的影响

以黄岛电厂温排水邻近海域为研究对象,2010年9月调查了电厂温排水对该海域大型底栖生物群落结构的影响。在9个站点共采集到大型底栖生物76种,平均生物量5．79 g/m2,平均密度830 m-2。利用Bray-Curtis相似性聚类对各样本大型底栖生物分析得出,调查区域可划分为4个群落。各样点Shannon-Wiener多样性指数在2．42～4．25之间,平均指数为3．67,其中靠近温排水区域站位的生物多样性呈现下降的趋势。丰度生物量比较（Abundance/biomass comparison, ABC）曲线分析结果显示,靠近排水口处的大型底栖生物群落受到一定程度的干扰。冗余分析（ RDA）结果表明,水温是影响底栖生物群落变化的最主要因子,对调查区域大型底栖生物群落变化的解释量达到60．5％,影响范围为排水口附近温升在3℃以上的区域。     

核电站温排水遥感监测方法研究——以田湾核电站为例

以江苏省连云港田湾核电站为主要研究区,通过热红外遥感技术研究温排水热污染现象,综合应用美国Landsat卫星热红外波段数据及地面气象测站资料,定量反演核电站建成前后附近海域水温分布与变化情况。研究结果表明,遥感技术完全能够满足温排水监测要求,对于完善近岸海域生态环境保护工作具有积极意义。     

Sorption and desorption kinetics of diuron,fluometuron, prometryn and pyrithiobac sodium in soils

Abstract

The sorption and desorption characteristics of four herbicides (diuron, fluometuron, prometryn and pyrithiobac‐sodium) in three different cotton growing soils of Australia was investigated. Kinetics and equilibrium sorption and desorption isotherms were determined using the batch equilibrium technique. Sorption was rapid (> 80% in 2 h) and sorption equilibrium was achieved within a short period of time (ca 4 h) for all herbicides. Sorption isotherms of the four herbicides were described by Freundlich equation with an r² value > 0.98. The herbicide sorption as measured by the distribution coefficient (K_d) values ranged from 3.24 to 5.71 L/kg for diuron, 0.44 to 1.13 L/kg for fluometuron, 1.78 to 6.04 L/kg for prometryn and 0.22 to 0.59 L/kg for pyrithiobac‐sodium. Sorption of herbicides was higher in the Moree soil than in Narrabri and Wee Waa soils. When the K_d values were normalised to organic carbon content of the soils (K_oC), it suggested that the affinity of the herbicides to the organic carbon increased in the order: pyrithiobac‐sodium < fluometuron < prometryn < diuron. The desorption isotherms were also adequately described by the Freundlich equation. For desorption, all herbicides exhibited hysteresis and the hysteresis was stronger for highly sorbed herbicides (diuron and prometryn) than the weakly sorbed herbicides (fluometuron and pyrithiobac‐sodium). Hysteresis was also quantified as the percentage of sorbed herbicides which is not released during the desorption step ω = [n_ad / n_de ‐1] x 100). Soil type and initial concentration had significant effect on ω. The effect of sorption and desorption properties of these four herbicides on the off‐site transport to contaminate surface and groundwater are also discussed in this paper.     

The boiling liquid expanding vapour explosion

The boiling liquid expanding vapour explosion (BLEVE) has existed for a long time and for most of this time it has been cloaked in mystery. Several theories have been put forward to explain this very energetic event but none have been proven. This paper describes a series of tests that have recently been conducted to study this phenomenon.

The study involved ASME code automotive propane tanks with nominal capacities of 400 litres. The tanks were exposed to a combination of pool and/or torch fires. These fire conditions led to thermal ruptures, and in some cases these ruptures resulted in BLEVEs. The variables in the tests were the pressure-relief valve setting, the tank wall thickness, and the fire condition.

In total, 30 tests have been conducted, of which 22 resulted in thermal ruptures. Of those tanks that ruptured, 11 resulted in what we call BLEVEs. In this paper, we have defined a BLEVE as the explosive release of expanding vapour and boiling liquid following a catastrophic tank failure. Non-BLEVEs involved tanks that ruptured but which only resulted in a prolonged jet release.

The objective of this study was to investigate why certain tank ruptures lead to a BLEVE rather than a more benign jet-type release. Data are presented to show how wall temperature, wall thickness, liquid temperature and fill level contribute to the BLEVE process.     

VARIABILITY IN THERMAL STRATIFICATION IN A RESERVOIR1

ABSTRACT: The thermal stratification characteristics of a flow-augmentation reservoir, Round Valley Reservoir, New Jersey, and attendant driving conditions were documented and analyzed for portions of three years. Substantial differences in the thermal stratification regime of the reservoir occurred in response to the documented changes in meteorological, operating, and light penetration conditions. The features of stratification that were affected included: the depth of the upper mixed layer, the average temperature of the epilimnion, the temperature gradient in the metalimnion, and the average temperature in the hypolimnion.