Modeling the e ects of constructed wetland on nonpoint source pollution control and reservoir water quality improvement

This article describes the integrated modeling approach for planning the size and the operation of constructed wetlands for maximizing retention of nonpoint source pollutant loads and reservoir water-quality improvement at a catchment scale. The experimental field-scale wetland systems (four sets, 0.88 ha each) have been in operation since 2002, where water depth was maintained at 30–50 cm and hydraulic loading rate was at 6.3–18.8 cm/day. The wetland system was found to be adequate for treating polluted stream water with stable removal e ciency even during the winter. The integrated modeling system (modified-BASINS) was applied to the Seokmoon estuarine reservoir watershed and calibrated with monitoring data from constructed wetland, stream, and reservoir. The calibrated integrated modeling system estimated that constructing wetlands on 0.5% (about 114 ha) of the watershed area at the mouth of reservoir could reduce 11.61% and 13.49% of total external nitrogen and phosphorus loads, respectively. It also might improve the nitrogen and phosphorus concentration of the reservoir by 9.69% and 16.48%, respectively. The study suggested that about 0.1%–1.0% of the watershed area should be allocated for constructed wetland to meet specified water-quality standards for the estuarine reservoir at the polder area where land use planning is relatively less complicated.     

运河徐州段重点水污染源的致突变研究

通过紫露草微核技术，对重点水污染源进行测定，弄清了各种废水的致突变性，为保护大运河的水资源提供了科学依据。经致变物污染负荷（生物指标）与常规的等标污染负荷（理化指标）比较，得出在评价水质时，应用致变物污染负荷更重要的结论，为环境科学工作者提供了重要参考。     

抚仙湖流域农业面源污染防治策略研究

阐述了云南省典型高原湖泊抚仙湖从源头防控、转移过程削减、终端拦截净化防治农业面源污染的多种策略,分析了抚仙湖农业面源污染防治策略的优缺点及对其他高原湖泊流域面源污染防治的启示,并提出了进一步提升农业面源污染防治效益的对策建议.     

海河干流流域暴雨径流非点源污染负荷解析与控制策略

随着点源污染逐渐得到有效控制,非点源污染对海河干流流域水环境污染的贡献日益增大,对其污染负荷进行科学测算成为海河干流水质达标方案制订的重要前提。基于GIS技术,通过土地利用类型划分,利用PLOAD模型对海河干流的暴雨径流非点源污染负荷进行了计算。结果表明,海河干流流域建设用地的比例依海河流向自上而下逐渐递减,而涉农用地逐渐增加,城区地表径流与农业面源污染分别是上、下游地区重要的非点源污染负荷来源。关于流域的暴雨径流非点源污染负荷,CODCr为15 619.29 t/a,NH3-N为369.16 t/a,TN为851.20 t/a,TP为250.29 t/a。为改善海河干流水质,非点源污染控制应纳入流域的污染物总量控制计划中,与点源污染一起参与环境容量的分配与控制。     

A.eutrophus 利用有机废水生产聚羟基烷酸

对真养产碱杆菌(     

水力停留时间和溶解氧对陶粒CANON反应器的影响

以人工配制无机高氨氮废水为进水,通过接种CANON污泥,以陶粒作为填料,研究了HRT和DO对生物膜CANON反应器的影响.试验过程中,控制进水氨氮浓度基本不变,依次控制反应器的HRT为9、7、5 h,同时控制DO的范围为1.16~3.20 mg·L-1.研究发现:1当DO为1.20~1.75 mg·L-1时,尽管提高DO有利于提高AOB的活性和系统内基质的传质效果,但是CANON反应器的NH+4-N、TN去除效果依然随着HRT的缩短而下降,尤其当DO超过2.50 mg·L-1时,TN去除效果大幅度下降;2当DO为1.20~1.75 mg·L-1时,随着HRT的缩短,CANON反应器的短程硝化性能趋于稳定,而当DO超过1.75 mg·L-1时,即使缩短HRT,其短程硝化性能依然遭到严重破坏;3CANON反应器中短程硝化稳定性能和去除效果较佳的条件是HRT为7 h,且DO控制在1.20~1.75 mg·L-1之间.HRT和DO是废水生物处理的重要运行参数,直接影响到生物处理的效果和出水水质,协调控制两者的变化范围,对提高CANON工艺对高氨氮废水的处理效果非常重要.     

中国南方生态系统的酸沉降临界负荷

将中国南方生态系统的酸沉降敏感性等级与用MAGIC模型在对应样点计算的临界负荷值相结合,对中国南方生态系统的酸沉降临界负荷进行了研究,并编制了1°×1°经纬度网格的临界负荷图．研究结果表明,中国南方生态系统硫沉降临界负荷大多在2.3～5.2gm²a之间,在地域分布上由东南向西北逐渐增大,其中临界负荷小于3.0g/m₂a的极敏感地区为浙江南部、广东与福建交界地区、贵州西南部和广西中部．     

农业非点源污染田间模型及其应用

非点源污染的负荷定量化研究是控制、评价和管理非点源污染的基础.农业非点源污染负荷估算包括农田排水估算和排水中的污染物浓度预测2个环节.依据水量平衡原理,农田排水应用DRAINMOD模型估算;将农田的施肥和灌溉过程"合成"作为田间污染物浓度的脉冲输入,农田排水中的污染物浓度变化则视作对应于此脉冲输入的响应过程,而污染物在田间的复杂迁移转化过程以逆高斯概率密度函数隐含表达.以此为基础,构建了农田尺度农业非点源污染负荷估算模型.以青铜峡灌区典型试验区为例,对稻田排水沟中硝态氮(NO_3~--N)和总磷(TP)的负荷过程进行了模拟,结果表明,模型估算结果和实测污染物负荷过程非常接近,Nash-Suttcliffe模拟效率系数分别为0.963和0.945,表明该模型具有较高的可靠性.     

基于中性盐提取的土壤重金属固液分配与自由态金属离子浓度测定

采用0.01mol·L-1CaCl2、0.002mol·L-1Ca(NO3)2和纯水(UPW)3种常用提取剂对我国南方两种典型农田重金属污染土壤进行提取试验.同时,应用土壤重金属固液分配多表面模型来预测提取液中重金属含量,结合道南膜技术(DMT)测定Ca(NO3)2提取液中自由态金属离子浓度,并与ECOSAT模型计算值进行比较.结果表明,提取剂中Ca2+浓度增加能显著提高土壤重金属溶出率,而提取液pH、溶解态有机碳(DOC)浓度却随溶液Ca2+浓度增加而降低.多表面模型(Multi-Surface Model)对大部分提取液金属浓度有较好的预测效果,部分土样提取液Cu、Pb、Zn浓度的预测效果较差.DMT测定的Ca(NO3)2提取液自由态重金属浓度与模型计算值较为一致,能够较准确地测定土壤溶液自由态重金属离子浓度.     

Enhanced struvite recovery from wastewater using a novel cone-inserted fluidized bed reactor

The feasibility of struvite recovery at low （12.5 mg/L） and high （120 mg[L） phosphorus concentrations was studied by constructing a novel fluidized bed reactor with cones （FBRwc） and without cones （FBRwoc）. The crystallization process was continuously operated for 133 days under different hydraulic retention times （HRT = 1-10 hr）, pH （7.5-10）, and molar ratios of Mg/P （0.75-1.75）, N/P （1-10） and Ca/Mg （0-2）. The optimum operating conditions of HRT, pH, Mg/P and N/P molar ratios were found to be 2 hr, 9, 1.25, and 7.5, respectively. Under these optimum conditions, the phosphorus precipitation efficiencies of FBRwc were 93% for low and 98% for high phosphorus influent; however, the efficiencies were 78% and 81% for FBRwoc, respectively. Due to crystal losses at each junction （17%-31%）, the crystal recovery efficiency of FBRwoc was relatively low （47%-65%） for both influent concentrations. However, the losses were minimal in FBRwc, which showed 75% and 92% crystal recovery for low and high phosphorus concentrations, respectively. At low calcium concentration, crystal chemical analysis showed the product to be pure struvite （〉 99%）. The scanning electron microscope and X-ray diffraction results further confirmed that the crystal recovered from FBRwc contained pure struvite, which could be considered a high quality fertilizer. Except HRT, all parameters （pH, Mg/P, N/P and Ca/Mg） were found to be influencing factors for FBRwc performance. Overall, inserting cones in each part of the reactor played a significant role in enhancing struvite recovery from a wide range of phosphorus-containing wastewater.