危险废物电镀污泥热处置特性研究

在获取典型危险废物原始电镀污泥的TG、DTG、DTA曲线的基础上,详细地分析了Salts泥的热特性．对不同终温下的焚烧减重率进行了试验,发现在焚烧温度低于700℃之前已经能很好的除去电镀污泥中的水分、有机质和挥发份．通过管式炉模拟实际焚烧炉工况,研究了不同试验条件对电镀污泥中的重金属浸出特性和迁移特性的影响,结果显示高温可以有效地抑制重金属的浸出特性,但对迁移特性的影响各不相同．     

施用生物质炭对黑土黑碳含量和结构特征的影响

生物质炭(Biochar,Bc)是黑碳(Black Carbon,BC)的一种,当前关于生物质炭在农业上的研究大都集中在其对土壤理化性质和作物生长的影响,而关于施用生物质炭对土壤黑碳结构和数量影响的研究很少.为了解施用生物质炭对土壤黑碳的影响,本试验采用盆栽试验的方法,设置4个处理,施加生物质炭量分别为0(CK)、6、12和24 t·hm-2,采用Wolbach-Anders法对土壤中的黑碳进行提取,运用元素分析、红外光谱和热重分析等方法研究了不同施入量的生物质炭对土壤黑碳产生的影响.实验结果表明:施用玉米秸秆生物质炭能明显增加土壤中黑碳的含量,随着生物质炭施用量的增加,不同处理相对于对照(CK)中土壤黑碳含量分别提升7.04%、22.96%和46.90%.施用玉米秸秆生物质炭降低了黑碳的脂族性、氧化性,提升了黑碳的缩合度、芳化度,提高了黑碳结构的稳定性,提高了土壤黑碳的热稳定性.施用玉米秸秆生物质炭能够提高p H,提高土壤的速效养分含量.     

水力负荷及固相碳源对BAF+多级土壤渗滤组合工艺处理污水的影响研究

碳源的选择及曝气量的控制是影响多级土壤渗滤系统(multi-soil-laying,即MSL)脱氮效果的重要因素.试验采用BAF+MSL两段式新型组合工艺,避免了传统MSL曝气过量抑制反硝化脱氮的风险.考察了不同水力负荷下,BAF+MSL对生活污水的净化效果,并比较研究了以聚丁二酸丁二醇酯(PBS)为反硝化碳源的MSL-1及木屑为碳源的MSL-2的脱氮除磷效果.结果表明,不同水力负荷下,系统对SS平均去除率为94.08%,对COD的去除率均在80%以上,出水COD在20mg·L-1以下.水力负荷对系统BAF段硝化性能影响较小,对MSL反硝化脱氮影响较大.BAF水力负荷为0.5、1及2m·3m-·2d-1时,BAF对NH4+-N的去除率均在90%以上,对TN的平均去除率依次为26.53%、11.09%、5.71%;对应MSL段水力负荷分别为0.25、0.50及1m·3m-·2d-1时,MSL-1对TN平均去除率分别为87.39%、65.09%、45.56%,MSL-2平均去除率依次为61.51%、42.52%、31.32%.MSL-1脱氮性能明显优于MSL-2,而两者除磷效果区别较小.随着水力负荷增大,MSL对TP去除率依次降低,MSL-1对TP平均去除率最高为91.97%.     

发动机燃烧室内壁材料热环境的气动热试验模拟技术研究

利用超声速矩形湍流导管和等离子电弧加热器模拟了发动机燃烧室内流和高超声速飞行器外壁面外流热环境,进行了平板表面冷壁热流测量和燃烧室内壁材料考核试验。结果表明:由于辐射换热的影响,在选取的两个典型来流条件下,发动机燃烧室内流热环境下的冷壁热流比外流热环境下的高出21%和40%,但是冷壁热流的增量基本相当,约为0.70~0.80MW/m²。随着冷壁热流的增加,辐射换热产生的热流增量的影响力会逐渐减小。材料考核时,相同配方的C/SiC复合材料在内流热环境下的表面温度高出约400℃,背面温度高出约90℃,这种差异对于发动机燃烧室内壁面材料考核至关重要,必须在材料考核试验中加以考虑。      

直接进样-热脱附-GC-MS快速测定大气细颗粒物中有机示踪物

建立了直接进样-热脱附-GC-MS快速测定细颗粒物中甾烷类和藿烷类有机示踪物的方法。经实验条件优化,13种目标化合物的线性回归方程的相关系数均在0.990以上,空白加标回收率为81.4%~102.3%,实际样品加标回收率为79.1%~112.9%,相对标准偏差小于13.2%。当采样体积为24 m~3时,各目标化合物的检出限为0.008~0.084 ng/m~3,方法灵敏度高。利用该方法测定了北京城区采暖季和非采暖季PM2.5实际样品,结果表明:各目标物均有检出,且采暖季的甾烷类和藿烷类化合物的总量均明显高于非采暖季。该方法无需复杂的前处理和有机溶剂,操作简便快捷,在颗粒物中非极性化合物的快速检测方面具有很大的应用价值。     

低压环境对锂电池热失控释放温度影响

为研究锂电池在民航飞行低压特殊环境的安全性及发生热失控灾害后的高温危险性,通过可模拟飞行变动条件的动压变温实验舱开展系列实验,研究锂电池在不同低压环境下的（101,60,30 kPa）多节18650型锂离子电池热失控温度特性,采集电池池体温度及热失控喷射释放温度等参数。研究结果表明:随环境压力降低,圆柱锂电池间的热失控传播并不能被阻断,但锂电池热失控灾害所释放产生的高温区域减少,且高温持续时间变短,释放所产生温度的高温危险性随环境压力的降低而有所降低。     

中国水泥生产环境负荷研究

基于生命周期理论,采用CML环境影响评价方法对我国水泥生产的环境负荷进行了定量分析.结果表明,水泥生产的环境影响主要体现在温室效应、不可再生能源消耗和不可再生资源消耗,其环境负荷分别占对应环境影响类型世界总负荷的2.76%、2.34%和1.39%.2004年我国水泥生产的环境负荷约占世界总负荷的1.28%,其中,立窑生产工艺、湿法回转窑生产工艺和新型干法生产工艺的环境负荷分别为0.84%,0.12%和0.32%.通过行业结构调整,用新型干法生产工艺取代其它落后的生产工艺,可使我国水泥生产的环境负荷降至世界总负荷的1%左右.     

A comparative study on the alternating mesophilic and thermophilic two-stage anaerobic digestion of food waste

An alternating mesophilic and thermophilic two stage anaerobic digestion(AD) process was conducted. The temperature of the acidogenic(A) and methanogenic(M) reactors was controlled as follows: System 1(S1) mesophilic A-mesophilic M;(S2) mesophilic A-thermophilic M; and(S3)thermophilic A-mesophilic M. Initially, the AD reactor was acclimatized and inoculated with digester sludge. Food waste was added with the soluble chemical oxygen demand(SCOD) concentrations of41.4–47.0 g/L and volatile fatty acids of 2.0–3.2 g/L. Based on the results, the highest total chemical oxygen demand removal(86.6%) was recorded in S2 while S3 exhibited the highest SCOD removal(96.6%). Comparing S1 with S2, total solids removal increased by 0.5%; S3 on the other hand decreased by 0.1 % as compared to S1. However, volatile solids(VS) removal in S1, S2, and S3was 78.5%, 81.7%, and 79.2%, respectively. S2 also exhibited the highest CH4 content, yield, and production rate of 70.7%, 0.44 L CH4/g VSadded, and 1.23 L CH4/(L·day), respectively. Bacterial community structure revealed that the richness, diversity, evenness, and dominance of S2 were high except for the archaeal community. The terminal restriction fragments dendrogram also revealed that the microbial community of the acidogenic and methanogenic reactors in S2 was distinct. Therefore,S2 was the best among the systems for the operation of two-stage AD of food waste in terms of CH4production, nutrient removal, and microbial community structure.     

热纤维梭菌不同菌株的纤维素降解和酒精生产能力

以高温厌氧细菌热纤维梭菌(Clostridium thermocellum LQRI和VPI菌株)和嗜热厌氧乙醇菌(Thermoanaerobacterethanolicus X514和39E菌株)为对象,以不同浓度纤维素为底物,分析了热纤维梭菌不同菌株的纤维素降解和酒精生产能力.结果表明,在热纤维梭菌纯培养体系中,LQRI对纤维素的降解能力明显高于VPI,前者约为后者的1.2倍,但两者的酒精生产能力没有显著差异,LQRI在1%纤维素条件下酒精终浓度约为12 mmol/L,VPI约为10 mmol/L.随着底物纤维素浓度的增加(1%、2%、5%),两者对纤维素降解和酒精生产能力均呈明显下降趋势.在热纤维梭菌和嗜热厌氧乙醇菌混合培养体系中,LQRI对纤维素的降解能力明显高于VPI,前者约为后者的1.28～1.58倍.随着底物浓度的增加,两者的纤维素降解率均逐渐下降,但热纤维梭菌对纤维素降解的绝对数值还受到其它混合培养菌种的影响.此外,LQRI+Thermoanaerobacter混合培养体系的酒精生产能力明显高于VPI+Thermoanaerobacter,前者约为后者的1.27～1.77倍.随着底物浓度的增加,混合培养体系酒精生产能力没有明显下降趋势.     

Moisture distribution in sludges based on di erent testing methods

Moisture distributions in municipal sewage sludge, printing and dyeing sludge and paper mill sludge were experimentally studied based on four di erent methods, i.e., drying test, thermogravimetric-di erential thermal analysis (TG-DTA) test, thermogravimetricdi erential scanning calorimetry (TG-DSC) test and water activity test. The results indicated that the moistures in the mechanically dewatered sludges were interstitial water, surface water and bound water. The interstitial water accounted for more than 50% wet basis (wb) of the total moisture content. The bond strength of sludge moisture increased with decreasing moisture content, especially when the moisture content was lower than 50% wb. Furthermore, the comparison among the four di erent testing methods was presented. The drying test was advantaged by its ability to quantify free water, interstitial water, surface water and bound water; while TG-DSC test, TG-DTA test and water activity test were capable of determining the bond strength of moisture in sludge. It was found that the results from TG-DSC and TG-DTA test are more persuasive than water activity test.