燃煤锅炉烟气脱硝技术的研发与应用

选择性催化还原技术（SCR）是燃煤锅炉最有效的烟气脱硝技术，NH3／NOx混合效果是该技术工程设计时遇到的难点之一。QI^2-SCR技术在“主动利用不均”理念的指导下，开发了关于喷氨格栅的专利技术，充分发挥了有限体积催化剂的性能，在较小氨逃逸率的前提下，实现了较高的脱硝效率。     

苯乙烯在有机-水两相界面上的分子氧选择性光氧化

以水为介质的氧化反应是一种有效的烯烃选择性绿色氧化和有机物的绿色处理过程.以苯乙烯为反应底物,开展了苯乙烯在室温、紫外光照射下的有机-水两相界面上的分子氧选择性光氧化反应.结果表明:在水溶液中,苯乙烯被选择性地光氧化成苯甲醛,苯甲醛的产率和选择性分别为28.5%和90.8%;而在无氧状态下,水溶液和有机溶剂中的苯乙烯光氧化反应都只得到非常少量的苯甲醛,产率仅有0.2%~0.4%.芳香端基烯烃（如3-甲基苯乙烯、4-甲氧基苯乙烯、1,1-二苯基乙烯）也能在水溶液中被分子氧选择性地光氧化,生成相应的羰基化合物;以双氧水为氧化剂,在水溶液中苯乙烯光氧化反应的苯甲醛产率为0.4%,以双氧水或分子氧为氧化剂时,醇溶剂中苯甲醛的产率均为0.6%~0.7%.研究显示,分子氧和水是苯乙烯光氧化反应的必须因素.      

焙烧温度对CeO_2(ZrO_2)/TiO_2选择性催化脱硝性能的影响

采用溶胶-凝胶法并以不同温度焙烧制备一系列CeO_2(ZrO_2)/TiO_2(CZT)催化剂,考察了CZT催化剂固相结构、酸量、比表面积等性能与催化活性的关系。采用XRD、BET、NH3-TPD、H2-TPR以及XPS等表征技术对催化剂进行表征。结果表明:焙烧温度为450℃时CZT催化剂具有最高的催化活性,其在240~400℃的温度窗口内活性均高于90%,且具有较好的抗水和抗硫中毒能力。随着焙烧温度的提高,催化剂表面的Ce和Zr原子进入体相晶格且Ce0.5Zr0.5O2向Ce0.75Zr0.25O2转变,导致催化剂的储释氧能力和氧化还原性能降低。另外,锐钛矿和金红石型TiO_2晶粒尺寸的增加,催化剂的有效比表面积和总酸量降低,因此CZT催化活性随着焙烧温度的提高而有所降低。换言之,大的比表面积、良好的氧化还原性能、表面Ce4+的富集以及酸性位的增多均有利于NH3-SCR活性的提高。     

Fe-MnOx-CeO2/ZrO2低温催化还原NO性能研究

以纳米ZrO2为载体,用浸渍法制备出Fe-MnOx-CeO2/ZrO2催化剂,考察了活性组分配比和助剂负载量对催化剂低温NH3选择性催化还原NO活性的影响,并对催化剂进行了XRD、SEM、EDS和BET表征;探讨了温度、H2O和SO2对Fe-MnOx-CeO2/ZrO2催化剂低温下NH3选择性催化还原NO的影响,结果表明,无SO2和H2O条件下,8%Fe-10%MnOx-CeO2/ZrO2催化剂具有良好的催化活性和稳定性.120℃时,催化剂的脱硝效率为85.23%,当温度升至180℃时,脱硝效率可达到92.0%.SO2和H2O共存条件下,催化剂易失活,采用傅立叶变换红外光谱对各反应阶段的催化剂进行了表征,对其失活机制进行深入研究,结果表明,催化剂失活的主要原因是催化剂表面硫酸铵盐的沉积和催化剂本身活性成分的硫酸盐化.     

H2S匀圆杂选择性催化氧化工艺及催化剂研究现状

论述了石油流化催化裂化烟气中H2S气体的选择性催化氧化处理工艺和工艺中所使用的各种类型选择性氧化催化剂.目前已发展并投入使用的选择性氧化工艺主要有:Superclaus工艺、Euroclaus工艺、Clinsulf-Do工艺、BSR/Hi-Activity工艺、Selectox工艺和Modop工艺等,各工艺具有不同的特点和应用范围.H2S选择氧化催化剂主要包括以下几种体系:碳体系、SiC载体体系、分子筛体系、氧化物体系和柱撑黏土体系等.其中碳体系和氧化物体系的研究开展的较早较多,关于分子筛体系的研究近期有所减少,SiC是研究人员认为非常有潜力的一个载体体系,其相关体系研究也一直在进行之中,柱撑黏土体系还处于初步研究阶段,离实际应用尚有距离.     

氨对垃圾焚烧飞灰浸出特性的影响及地球化学模拟

垃圾焚烧飞灰可能因为选择性非催化还原法(SNCR)脱硝过程中氨泄漏、垃圾携带的渗滤液受热挥发等原因而吸附氨.本研究中采用人为添加氨水,在pH为3.66～12.44范围内,研究氨对飞灰中溶解性有机碳(DOC)和重金属浸出的影响,并利用地球化学模拟软件Visual MINTEQ从金属化学形态分布上分析氨对飞灰浸出的影响机制.结果表明,DOC在pH>9和有高浓度氨(≥1 357 mg·L-1)存在时,其浸出量大幅增加,而在浸出液中氨的水平不高于537 mg·L-1时则受氨的影响很小;在pH<6时,飞灰中各金属主要以自由态的金属离子和金属-氯络离子形态大量溶出,且受氨的影响较小;而在pH为8～12的碱性环境中和氨浓度较高时(≥3 253 mg·L-1),氨与金属生成了可溶性的金属-氨配合物,能显著增加Cd、Cu、Ni、Zn的浸出,且在pH=9附近时浸出量达到最大值,但氨对Al和Pb的浸出影响甚微;在pH>12时,Cd、Cu、Ni、Zn主要以羟基金属离子形式存在.在氨浓度为3 253 mg·L-1时,通过利用Visual MINTEQ模拟浸出值与试验数据的对比,发现Al、Pb、Zn的浸出主要由溶解/沉淀模型控制,而Cd、Cu、Ni由溶解/沉淀模型和表面吸附反应模型同时控制,且Visual MINTEQ模型能较好地预测飞灰中Al、Cu、Pb、Zn的浸出特性.     

Fe2O3 particles as superior catalysts for low temperature selective catalytic reduction of NO with NH3

Fe203 particle catalysts were experimentally studied in the low temperature selective catalytic reduction （SCR） of NO with NH3. The effects of reaction temperature, oxygen concentration, [NH3]/[NO] molar ratio and residence time on SCR activity were studied. It was found that Fe203 catalysts had high activity for the SCR of NO with NH3 in a broad temperature range of 150-270℃, and more than 95% NO conversion was obtained at 180℃ when the molar ratio [NH3]/[NO] = 1, the residence time was 0.48 seconds and 02 volume fraction was 3%. In addition, the effect of SO2 on SCR catalytic activity was also investigated at the temperature of 180℃. The results showed that deactivation of the Fe2O3 particles occurred due to the presence of SO2 and the NO conversion decreased from 99.2% to 58% in 240 min, since SO2 gradually decreased the catalytic activity of the catalysts. In addition, X-ray diffraction, Thermogravimetric analysis and Fourier transform infrared spectroscopy were used to characterize the fresh and deactivated Fe2O3 catalysts. The results showed that the deactivation caused by SO2 was due to the formation of metal sulfates and ammonium sulfates on the catalyst surface during the de-NO reaction, which could cause pore plugging and result in suppression of the catalytic activity.     

Kinetics of selective catalytic reduction of NO by NH3 on Fe-Mo/ZSM-5 catalyst

The catalyst of Fe-Mo/ZSM-5 has been found to be more active than Fe-ZSM-5 and Mo/ZSM-5 separately for selective catalytic reduction (SCR) of nitric oxide (NO) with NH3. The kinetics of the SCR reaction in the presence of O2 was studied in this work. The results show that the observed reaction orders were 0.74-0.99, 0.01-0.13, and 0 for NO, O2 and NH3, respectively, at 350-450℃. And the apparent activation energy of the SCR was 65 kJ/mol on the Fe-Mo/ZSM-5 catalyst. The SCR mechanism was also deduced. Adsorbed NO species can react directly with adsorbed ammonia species on the active sites to form N2 and H2O. Gaseous O2 might serve as a reoxidizing agent for the active sites that have undergone reduction in the SCR process. It is also important to note that a certain amount of NO was decomposed directly over the Fe-Mo/ZSM-5 catalyst in the absence of NH3.     

Effect of manufacturing methods of AgCl/Al2O3 catalyst on selective catalytic reduction of NOx

The AgCl/Al2O3 catalyst has potential for use in the selective catalytic reduction (SCR) of NOx. A compound hydrocarbon, following oxygenation is used as a type of reducing agent. In this experiment, the AgCl/Al2O3 catalyst was produced by four different methods, and the differences among their reduction catalysis of NOx were compared. Ethanol was used as a type of reducing agent. X-ray diffraction analysis was performed to study the crystalline structure and scanning electron microscope and transmission electron microscope (TEM) were applied to determine the microindentation. The results indicated that, in the range of 350–400°C, there was no significant difference on the NOx reduction rate; however, there was dispersion at high and low temperature ranges. The size of the AgCl particles was about 20–100 nm.     

燃煤电厂烟气氮氧化物排放控制技术发展现状

在广泛查阅文献的基础上,对近年来国内外已成功应用和正在研究开发的一些主要的燃煤烟气氮氧化物控制技术进行了介绍。结合我国目前脱硝行业整体水平和国家环保政策要求,对我国脱硝行业技术研发方向提出了建议。