制药废水中磷霉素和α-苯乙胺的生物降解及相互作用

以比耗氧速率SOUR、呼吸抑制率和发光细菌光损失为衡量指标, 研究了在磷霉素、α-苯乙胺及其混合物作用下,活性污泥和发光细菌的可生化性和急性毒性的变化.结果表明, α-苯乙胺的急性毒性和对活性污泥的呼吸抑制率均大于磷霉素. α-苯乙胺与磷霉素混合液的可生化性和急性毒性两者在混合物中的比例有关,当α-苯乙胺所占比例低于25%时,混合液的可生化性基本不受两者比例的影响;但当α-苯乙胺所占比例高于25%时,混合液的可生化性随着α-苯乙胺所占比例的增加而降低.当混合液中α-苯乙胺所占比例为25%时,其急性毒性最低.     

基于国内水泥生产现状的碳排放因子测算

水泥生产过程中碳排放因子的测算是计算水泥碳排放量的基础,为了准确测算我国水泥行业熟料煅烧阶段碳酸盐矿物分解释放CO2的碳排放因子,就需要对水泥生产线上相关样品做成分测定和综合分析.通过对国内近百条代表性较强的水泥生产线上的生料、熟料、水泥、石灰石、燃煤等样品进行钙、镁、烧失量、碳酸盐等化学成分的定量分析,并考虑新型干法窑和立窑两种生产工艺类型的差别,分析测算了基于国内水泥生产的工艺碳排放因子.结果表明:生料碳酸盐法测算碳排放因子的结果较熟料法的结果低约10kgCO2/tcl;不同窑型的碳排放因子存在明显差异,新型干法窑的碳排放因子多集中在500~520kgCO2/tcl,立窑碳排放因子多集中在480~500kgCO2/tcl;多数熟料含有少量碳酸盐.生料碳酸盐法不涉及燃煤灰分的化学成分,可以规避燃煤灰分成分的影响,测算碳排放因子采用生料碳酸盐法较准确,并且应基于不同窑型,同时考虑碳酸盐分解率问题.     

污泥负荷对生物处理系统耐药细菌的影响研究

为了研究污水生物处理工艺中抗药性细菌生长和分布特性及污泥负荷的影响,构建了不同处理负荷的活性污泥工艺,并以磺胺嘧啶抗性异养菌为例,阐述了污泥负荷对活性污泥系统中典型抗药细菌的生长及排放特性的影响.结果表明,污泥负荷增大有利于磺胺嘧啶抗性异养菌的生长繁殖,负荷提高后净比生长速率和细菌产量分别由0.32d-1和2.3×106CFU/d提高至0.33d-1和3.1×106CFU/d,活性污泥、出水和剩余污泥中抗药菌的浓度也均显著提高(P < 0.05),但对抗药细菌的相对丰度无显著改变.低污泥负荷下[0.24kg COD/(kg MLSS?d)]抗药细菌主要通过剩余污泥形式排放,排放量比(泥中排放量/水中排放量)为28.4;负荷提高至0.4kg COD/(kg MLSS?d)后,出水抗药细菌排放量显著提高,排放量比为1.1.处理相同水量,高污泥负荷下排放的抗药细菌总量明显降低,提高污泥负荷有利于活性污泥系统抗药性风险的控制.     

剩余污泥热水溶性有机物的提取方法优化研究

热水溶性有机物含量和组成是表征剩余污泥(简称为污泥)中有机质生物可利用性的重要手段.分析了不同热水淬时间(1~24h)和不同ρ(污泥)(0.7~36.0g/L)对热水溶性蛋白质和碳水化合物等溶出的影响,据此对剩余污泥中热水溶性有机物的提取方法进行了优化. 结果表明:污泥在60℃水淬8h时,水溶性蛋白质和碳水化合物的溶出率达到最大,分别为34.6%和36.1%;但是,随着水淬时间的延长,部分蛋白质被转化成氨氮,部分碳水化合物也发生了转化和降解,致使二者的浓度降低. 考虑测试分析的时间效率和溶出率稳定性,污泥热水溶性有机物最优水淬时间建议设置为5h. 研究结果表明,热水溶性有机物的溶出率随ρ(污泥)降低呈升高趋势,当ρ(污泥)为0.7g/L时,热水淬5h后蛋白质和碳水化合物的溶出率最大,二者分别为52.9%和36.6%.      

菌根真菌侵染对植物生物量累积的影响

为了从生态系统尺度探讨菌根资源与植物生物量累积的关系,调查了鼎湖山不同成熟度的三个森林群落主要优势树种的菌根侵染情况.综合分析各森林群落优势树种的个体数、生物量和菌根侵染率发现：1）菌根侵染率与径向生长速率相关,植物生长迅速的阶段菌根侵染率更高.中径级（胸径15-30 cm）的马尾松（Pinus massoniana）和锥（Castanopsis chinensis）的侵染率比小径级（胸径1-15 cm）个体的侵染率高,而大径级个体（胸径30 cm 以上）的侵染率略低于中径级个体的侵染率.木荷（Schima superba）则表现出侵染率随着胸径增大而增高的趋势.2）树种在群落内的侵染率越高,其对群落生物量的贡献率越大.如马尾松在马尾松林和混交林的侵染率分别为（77.30±18.02）%和（40.50±14.42）%,其对马尾松林群落生物量的贡献率达到87.43%,是对混交林生物量贡献率（17.51%）的5 倍.混交林和阔叶林的共有优势树种锥的侵染率和生物量贡献率也有存在相同规律.3）根系碳储量占群落总碳储量比例较高的群落其优势树种平均侵染率相对较高.马尾松林、混交林和季风常绿阔叶林中,根系碳储量占群落总碳储量的比例分别为55%、54%、42%,群落优势树种平均侵染率分别为（66.73±10.55）%、（46.97±27.28）%、（54.22±25.45）%,马尾松林的根系碳储量和平均侵染率均高于混交林和季风常绿阔叶林.以上结果表明,菌根真菌侵染对于植物个体生长速率以及群落水平的生物量累积具有-定的促进作用.     

皇竹草对土壤阿特拉津的降解特性

为了探明种植皇竹草(Pennisetum hydridum)对土壤阿特拉津降解的促进作用,通过盆栽试验研究了皇竹草对土壤阿特拉津的降解动态、转移特征以及土壤阿特拉津残留浓度与土壤相关酶活性的关系。结果表明:与未种植皇竹草相比,种植皇竹草土壤阿特拉津降解率明显提高,皇竹草对未灭菌和灭菌土壤阿特拉津的降解率分别提高52.84和42.38百分点;与未种植皇竹草处理相比,灭菌和未灭菌条件下种植皇竹草处理阿特拉津在土壤中的半衰期可分别缩短64.35和53.21 d;土壤中阿特拉津被皇竹草吸收后逐步由地下部分向地上部分转移,随着培养时间的延长,转移系数变大;土壤中阿特拉津残留浓度与土壤过氧化氢酶、过氧化物酶、转化酶和多酚氧化酶活性呈显著负相关(P0.05或P0.01)。认为种植皇竹草有助于阿特拉津的降解。     

Comparison of growth and lipid accumulation properties of two oleaginous microalgae under different nutrient conditions

This study compared the growth and lipid accumulation properties of two oleaginous microalgae, namely, Scenedesmus sp. LX1 and Chlorella sp. HQ, under different nutrient conditions. Both algal species obtained the highest biomass, lipid content and lipid yield under low-nutrient conditions （mBGll medium）. The biomass, lipid content and lipid yield of Scenedesmus sp. LX1 were 0.42g·L^-1, 22.5% and 93.8mg·L^-1, respectively. These values were relatively higher than those of Chlorella sp. HQ （0.30g·L^-1, 17.1% and 51.3mg·L^-1, respectively）. These algae were then cultivated in an SE medium that contained more nutrients; as a result, the biomass and lipid yield of Scenedesmus sp. LX1 reduced more significantly than those of Chlorella sp. HQ. Opposite results were observed in lipid and triacylglycerols （TAGs） contents. The cell sizes of both algal species under low-nutrient conditions were larger than those under high-nutrient conditions. Chlorella sp. HQ cells did not aggregate, but Scenedesmus sp. LX1 cells flocculated easily, particularly under low-nutrient conditions. In summary, low-nutrient conditions favour the growth and lipid production of both algae, but Scenedesmus sp. LX1 outperforms Chlorella sp. HQ.     

Validation of the UN test method N.5

Many substances react with water in such a way that flammable gases are formed. For transport issues this reaction may possess a considerable hazard especially if the cargo is wetted by rain or by water from other sources. In the UN Recommendations on the Transport of Dangerous Goods these kinds of problems are addressed. The UN test N.5 “Test method for substances which in contact with water emit flammable gases” corresponds to this hazard. Classification according to the test method is done by measurement of the gas evolution rate of the flammable gas by any suitable procedure. At BAM a gravimetric approach is used to measure the gas evolution rate. In this paper we present the evaluation of the apparatus by means of an absolute calibration routine utilizing a reaction where a known amount of gas is produced as well as the evaluation of important parameters influencing the gas evolution rate using different substances. It can be shown that the apparatus is capable of measuring absolute gas volumes as low as 6 mL with an acceptable error of about 17% as determined from the reaction of Mg with demineralized water.     

工伤保险行业差别费率确定方法探讨

制定合理的行业差别费率对于工伤保险基金的稳定、促进企业改善安全生产状况具有积极作用.我国工伤保险制度处于起步阶段,有些地区对行业差别费率厘定进行了探索,但费率与风险的关联性不强,影响了低风险企业参加工伤保险统筹的积极性.本文针对工伤统计数据缺乏的现状,分析了现阶段工伤保险行业差别费率确定方法的研究现状,重点讨论了确定行业风险等级的3种方法,即聚类分析法、风险系数测评和模糊风险评估法的应用过程以及优缺点;另外,强调了在确定行业风险指数时,应注意根据不同事故类别的严重度来确定各风险因素指标的权重大小.最后,应用风险评估理论分析工伤保险行业差别费率的运作机理,提出应用工伤赔付支出费用计算行业差别费率的数学公式,此公式原理清晰、操作方便,且有利于各统筹地区根据实际情况划分行业差别费率.     

Continuous biohydrogen production from diluted molasses in an anaerobic contact reactor

An anaerobic contact reactor (ACR) system comprising a continuous flow stirred tank reactor (CSTR) with settler to decouple the hydraulic retention time (HRT) from solids retention time (SRT) was developed for fermentative hydrogen production from diluted molasses by mixed microbial cultures. The ACR was operated at various volumetric loading rates (VLRs) of 20–44 kgCOD·m^-3·d^-1 with constant HRT of 6 h under mesophilic conditions of 35°C. The SRT was maintained at about 46–50 h in the system. At the initial VLR of 20 kgCOD·m^-3·d^-1, the hydrogen production rate dropped from 22.6 to 1.58 L·d^-1 as the hydrogen was consumed by the hydrogentrophic methanogen. After increasing the VLR to 28 kgCOD·m^-3·d^-1 and discharging the sludge for 6 consecutive times, the hydrogentrophic methanogens were eliminated, and the hydrogen content reached 36.4%. As the VLR was increased to 44 kgCOD·m^-3·d^-1, the hydrogen production rate and hydrogen yield increased to 42.1 L·d^-1 and 1.40 mol H₂·molglucose-consumed^-1, respectively. The results showed that a stable ethanol-type fermentation that favored hydrogen production in the reactor was thus established with the sludge loading rate (SLR) of 2.0–2.5 kgCOD·kgMLVSS^-1·d^-1. It was found that the ethanol increased more than other liquid fermentation products, and the ethanol/acetic acid (mol/mol) ratio increased from 1.27 to 2.45 when the VLR increased from 28 to 44 kgCOD·m^-3·d^-1, whereas the hydrogen composition decreased from 40.4% to 36.4%. The results suggested that the anaerobic contact reactor was a promising bioprocess for fermentative hydrogen production.