Optimal Absorbent Evaluation for the CO2 Separating Process by Absorption Loading,Desorption Efficiency,Cost, and Environmental Tolerance

The CO₂ absorption capacities of potassium glycinate, potassium sarcosinate (choline, proline), mono-ethanolamine (MEA), and tri-ethanolamine were evaluated to find the optimal absorbent for separating CO₂ from gaseous products by a CO₂ purification process. The absorption loading, desorption efficiency, cost, and environmental tolerance were assessed to select the optimal absorbent. MEA was found to be the optimum absorbent for separating the CO₂ and H₂ mixture in gaseous product. The maximum absorption loading rate was 0.77 mol CO₂ per mol MEA at temperature of 20°C and absorbent concentration of 2.5 mol/L, whereas desorption efficiency was 90% by heating for 3 h at 130°C. MEA was found to be an optimal absorbent for the purification process of CO₂ during gaseous production.     

Feasibility of honeycomb monolith supported sugar catalyst to produce biodiesel from palm fatty acid distillate (PFAD)

Carbon coated monolith was prepared by sucrose solution 65 wt.% via dip-coating method. Sulfonation of incomplete carbonized carbon coated monolith was carried out in order to synthesize solid acid catalyst. The textural structure characteristics of the solid acid catalyst demonstrated a low surface area and pore volume. Palm fatty acid distillate (PFAD), a by-product of palm oil refineries, was utilized as oil source in biodiesel production. The esterification reaction subjected to different reaction conditions was performed by using the sulfonated carbon coated monolith as heterogeneous catalyst. The sulfonation process had been performed by using vapour of concentrated H₂SO₄ that was much easier and efficient than liquid phase sulfonation. Total acidity value of carbon coated monolith was measured for unsulfonated sample (0.5 mmol/g) and sulfonated sample (4.2 mmol/g). The effect of methanol/oil ratio, catalyst amount and reaction time were examined. The maximum methyl ester content was 89% at the optimum condition, i.e. methanol/oil molar ratio (15:1), catalyst amount (2.5 wt.% with respect to PFAD), reaction time (240 min) and temperature 80 °C. The sugar catalyst supported on the honeycomb monolith showed comparable reactivity compared with the sugar catalyst powder. However, the catalyst reusability studies showed decrease in FFA% conversion from 95.3% to 68.8% after four cycles as well as the total acidity of catalyst dropped from the value 4.2 to 3.1 mmol/g during these cycles. This might be likely due to the leaching out of SO₃H group from the sulfonated carbon coated monolith surface. The leaching of active species reached a plateau state after fourth cycle.     

自动电位滴定法测定水中氯离子

以银电极为响应电极，用硝酸银溶液滴定水中氯离子，等当点时，产生电位突跃，以此确定终点电位，在仪器上锁定的此终点电位值，从而完成样品的自动分析。     

乌鲁木齐市主要街道空气中一氧化碳污染规律的研究

本文通过对影响街道空气中一氧化碳污染的因素进行了大量的监测及综合分析,找出乌鲁木齐市主要街道空气中一氧化碳的污染规律,为控制我市汽车污染提供科学依据.     

过氧化聚吡咯/聚乙烯吡咯烷酮修饰碳糊电极测定废水中苯酚

建立了过氧化聚吡咯(OPPy)和聚乙烯吡咯烷酮(PVP)修饰碳糊电极测定废水中苯酚的方法.优化了试验条件,苯酚的氧化峰电流在1.0×10-5 mol/L～1.0×10-3 mol/L之间线性关系良好,检出限为1.0×10-6 mol/L.该电极制作简单,选择性好,测定灵敏度高,精密度与准确度均符合要求.     

库仑滴定法测定一氧化碳

本文就一氧化碳的测定条件和CO氧化过程中氧化剂的选择进行了研究。试验表明:ReAO_4-Ⅱ为氧化CO的活性催化剂,转化率可达100％(在300℃以上),本法简便,可用于空气中一氧化碳的测定和催化剂对CO活性测试。     

城市高架道路建设对机动车尾气污染的影响分析

通过现场观测和对比，分析了城市一般道路上和城市高架道路下机动车排放污染物浓度差异的原因，分析结果表明，扩散条件对城市机动车尾气污染有着重要影响，例举日本对城市高架道路建设的有关规定，提出应重视城市高架道路建设的环境预评估等。     

BOD5测定方法的研究

通过对比实验，对BOD5的测定方法进行研究，探索用氧电极法测定BOD5的可能性和可行性，对其不足之处提出相应的解决措施，使之能更适用于科研、监测教学等方面的需要。     

煤烟型大气污染解决方法

重点介绍了新型燃煤工艺——水平火焰无烟工业炉及其特点，并提出排烟尾气处理的资源化方案。     

油团聚法处理炭黑废水的研究

根据炭黑疏水性的特点 ,本试验采用油团聚工艺成功地处理了炭黑废水。经处理后 ,出水中炭黑含量小于 5.0 mg/ L,出水可回用 ,回收的炭黑用四氯化碳处理后 ,经过滤干燥可得到含水率小于 1 .0 %的炭黑 ,油相可回用。