BiFeO3可见光催化降解甲基紫

采用柠檬酸-硝酸盐燃烧法制备了光催化剂BiFeO₃。采用SEM,XRD,FTIR等技术对光催化剂BiFeO₃进行表征。表征结果显示,光催化剂BiFeO₃晶相纯、粒径小、比表面积大,存在Fe#x02014;O的弯曲振动和伸缩振动。实验结果表明：通过鼓气及加入H₂O₂可有效提高BiFeO₃对甲基紫可见光催化降解的效率;在300mL质量分数为1.5#x000d7;10^-5的甲基紫溶液中加入0.9g光催化剂BiFeO₃和0.1mL质量分数为30%的H₂O₂溶液,当反应时间为240min时,甲基紫去除率可达99%。     

Wood-Specific Polycyclic Aromatic Hydrocarbon (PAH) Patterns in Soot Using Gas Chromatography-Atmospheric Pressure Laser Ionization-Mass Spectrometry (GC-APLI-MS)

If organic matter is burnt, the combustion of wood produces the highest amounts of polycyclic aromatic hydrocarbons (PAHs) compared with other fossil energy sources such as oil, coal, or gas. Emissions from wood combustion are increasingly of special interest due to the rising use of wood as a renewable energy source in residential heating in Europe. To the authors' knowledge, reproducible wood-specific PAH patterns in soot were identified for the first time by use of a sampling interval of only 5 min in this study. The short sampling interval was enabled by the very sensitive analytical method of gas chromatography–atmospheric pressure laser ionization–mass spectrometry (GC-APLI-MS) applied. The analysis of 40 PAH of soot from wood logs of spruce, pine, larch (softwood) and beech, birch, oak (hardwood), and wood pellets, as well as wood briquettes, showed 13.46–250.62 mg/kg for ∑40 PAH and 10.75–177.94 mg/kg for the U.S. Environmental Protection Agency PAH standard (without acenaphthylene and anthracene). Highest concentrations occurred in the samples from birch with bark, beech, and wood briquettes. Indeno[1,2,3-cd]pyrene, naphthalene, and alkylated naphthalenes were also detected. Significant concentrations of the very toxic dibenzopyrenes (up to 11.30 mg/kg) are reported. Softwood soot contained highest amounts of 2–4-ring PAH, followed by hardwood which is in accordance with the presence of highest amounts of abietic acid in softwood, a known precursor of retene and phenanthrene. PAH in soot from five spruce samples from different locations show a mean ∑40 PAH concentration of 13.46 mg/kg (n = 5, minimum 8.03, maximum 23.32 mg/kg, SD = 5.65) and exhibited a typical pattern that differed from all other wood soot samples. The distributions of alkylated naphthalenes of the spruce samples show a bell-shape distribution in contrast to the alkylated phenanthrenes/anthracenes of all samples (except the wood pellets), showing a slope distribution. The data indicate that wood-specific PAH patterns exist and under the applied conditions, spruce logs produced the least toxic soot.     

某“W”型锅炉炉效低的综合治理

针对某锅炉经济性差的问题,从设备、运行及自动控制等方面分析,并进行了相应整改。影响炉效的主要因素有煤质恶化、灰渣含碳量高、排烟温度高和CO浓度高等,同时炉膛燃烧不稳定也是影响燃烧效率的重要因素。通过漏风整改、制粉系统优化、燃烧优化调整和控制系统优化等方法有效提高了锅炉经济性。研究表明：分析锅炉经济性降低的影响因素时应抓住主要因素,兼顾其他,科学的生产管理是保证锅炉运行经济性的重要基础;入炉煤质恶化是最主要的外在因素;良好的自动控制系统能有效稳定燃烧参数,提高燃烧效率;降低飞灰含碳量的主要工作应集中在制粉系统优化调整;完整而系统的燃烧调整试验能够保证锅炉运行控制参数的科学合理,并需要正确调整氮氧化物排放和锅炉效率之间的关系。     

Accurate sampling of PCDD/F in high temperature flue-gas using cooled sampling probes

In a laboratory-scale combustion reactor, flue-gas samples were collected at two temperatures in the post-combustion zone, 700 °C and 400 °C, using two different water-cooled sampling probes. The probes were the cooled probe described in the European Standard method EN-1948:1, referred to as the original probe, and a modified probe that contained a salt/ice mixture to assist the cooling, referred to as the sub-zero probe. To determine the efficiency of the cooling probes, internal temperature measurements were recorded at 5 cm intervals inside the probes. Flue-gas samples were analyzed for polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs). Samples collected at 700 °C using the original cooling probe showed higher concentrations of PCDD/Fs compared to samples collected using the sub-zero probe. No significant differences were observed between samples collected at 400 °C. The results indicated that artifact formation of PCDD/Fs readily occurs during flue-gas sampling at high temperatures if the cooling within the probe is insufficient, as found for the original probe at 700 °C. It was also shown that this problem could be alleviated by using probes with an enhanced cooling capacity, such as the sub-zero probe.Although this may not affect samples collected for regulatory purposes in exit gases, it is of great importance for research conducted in the high-temperature region of the post-combustion zone.     

铁及铁铜氧化物对臭氧氧化酸性红B的催化效能

采用自蔓延溶胶凝胶法分别制备了铁氧化物和铁铜复合氧化物催化剂,以酸性红B为降解对象,对比了单独臭氧氧化、铁氧化物和铁铜复合氧化物催化臭氧氧化对酸性红B的降解效果,考察了磁力搅拌速度(500～1 640 r/min)、溶液pH(3～11)、臭氧投加速率(3.55～28.4 mg/min)对铁铜复合氧化物催化性能的影响。结果表明,与单独臭氧氧化比较,铁氧化物和铁铜复合氧化物均能加速酸性红B的降解,促进色度和COD的去除,结合催化剂的表征结果,推断催化剂表面羟基促进臭氧分解产生.OH是其氧化性能较好的主要原因,另外,催化剂的吸附能力对催化性能也有一定影响。随着磁力搅拌速度、溶液pH、臭氧投加速率的增大,铁铜复合氧化物催化臭氧氧化酸性红B的效果越好。     

板材类生物质燃烧及动力学特性热重研究

采用非等温升温法研究了4种板材类生物质在空气气氛下的燃烧特性和动力学特性。通过对TG、DTG等曲线的分析,发现4种板材燃烧过程均可分成3个阶段,即水分蒸发阶段、挥发份析出(或燃烧)阶段和固定碳燃烧阶段。综合燃烧特性:松木集成材>纤维密度板>夹芯胶合板>刨花板。4种板材均具有良好的燃烧特性。4种生物质燃烧均存在1个吸热峰和2个放热峰,分别与挥发分析出峰、挥发分燃烧、固定碳燃烧对应。采用Fridman法和Fridman-Carroll法分别对4种板材的动力学参数进行了计算,2种方法得出的结果符合较好。分析得出:由于生物质燃烧与环境换热、挥发分析出吸热、固定碳燃烧放热等因素作用,4种生物质的表观活化能高温区均低于低温区。动力学计算结果表明:松木集成材平均表观活化能最低,燃烧反应能较容易进行。     

MnxCe1-xO2／γ-Al2O3催化剂的制备及其催化甲苯的燃烧性能

以γ-Al2O3为载体,以MnxCe1-xO2为催化活性组分,采用浸渍法制备了一系列负载型MnxCe1-xO2／γ-Al2O3催化剂（x=0、0．2、0．4、0．6、0．8、0．9、1）,在固定床反应器中评价了催化剂对甲苯的催化燃烧性能。结果表明,MnxCe1-xO2／γ-Al2O3催化剂的催化活性与催化剂的焙烧温度、活性组分MnxCe1-xO2的负载量以及Mn、Ce摩尔比有显著关系,其中焙烧温度550℃、负载量为20％、Mn、Ce摩尔比为4：1时,即MnxCe1-xO2／γ-Al2O3催化剂对甲苯的催化性能最佳,反应温度为180℃时,甲苯的转化率达到95％。并在连续100h的稳定性操作后,催化剂的活性基本无变化。采用XRD、BET以及SEM等分析测试手段对催化剂的结构以及表面进行了表征。     

层燃螺旋炉排焚烧技术处理含油污泥研究

通过对几种含油污泥无害化处理技术的比选,分析不同处理技术物耗、能耗情况,优选出经济有效的含油污泥焚烧技术,结合新疆油田含油污泥的特点,采用层燃螺旋炉排焚烧技术,利用其燃烧热能生产蒸汽用于原油生产,采用余热吸收急冷与碱液半干法除酸技术,有效控制了二次污染;采用布袋除尘与烟尘固化技术确保了烟气达标排放。年节省成本支出3095.88万元。     

垃圾炉一次风量对炉床燃烧影响的仿真研究

针对垃圾焚烧炉床层内垃圾燃烧过程复杂性及影响垃圾燃烧效率因素多的问题,运用数值仿真方法对某垃圾焚烧炉床层垃圾燃烧进行了模拟,获得了垃圾质量流失速率、水分蒸发速率、挥发分释放速率、焦炭燃烧速率和烟气的温度;并在50~1 000 Nm3/min范围内改变一次风流量,获得了床层质量流失比值、过剩空气系数和烟气中各组分的质量百分比含量。仿真结果显示,一次风流量取值517.47~6`32.09 Nm3/min时燃烧效率较高;炉排两端区域的一次风流量在50~75 Nm3/min时,可以使垃圾床表面平均温度明显提高,而且还可以提高燃烧效率,同时减少供风总量,节约能源与动力资源。本研究对优化设计垃圾焚烧炉,提高床层内垃圾的燃烧效率有一定参考价值。     

固硫灰渣深度处理焦化废水的实验研究

选用同硫灰渣深度处理经生化处理后焦化废水,采用分光光度计法评价焦化废水的处理效果,采用XRD、XRF、SEM和IR等分析材料的成分、结构和微观形貌等.结果表明,固硫灰渣用量60 g/L、吸附时间15 min,焦化废水的脱色率可达94.22%,COD从原水的76.01 mg/L降低到处理后的5.76 mg/L,NH+4-...