Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.     

确定压力容器安全系数原则

压力容器安全系数与材料参数紧密相关,确定材料许用应力值时,需要同时考虑材料抗拉强度和屈服强度更为合理;奥氏体不锈钢材料具有非常好的应变强化能力和韧性,为充分发挥奥氏体不锈钢材料优良性能,选取奥氏体不锈钢材料许用应力值时,需要特殊考虑。压力容器安全系数的选取建立在经验基础上,在保障压力容器安全性前提条件下,为节省材料和降低成本,随着理论研究深入和科学实验的进步,压力容器安全系数有所降低,这是科学设计和实用成功经验结合的结果。     

炭催化剂吸附剂标准物质的研制

本文介绍了炭催化剂吸附剂标准物质的研制过程。对标准物质的制备技术、均匀性检验、稳定性考察及定值和不确定度进行了逐项分析。采用活性炭浸渍、煅烧技术制得炭催化剂吸附剂标准物质。试验结果表明,该标准物质定值结果准确,均匀性、稳定性良好。铜含量的标准值为11．06％,扩展不确定度为0．13％。     

广东省杨村华侨柑桔场土壤微量元素含量与分布的研究

采集并分析全场不同母质形成的有代表性的土壤样本142个.研究结果表明,各类土壤全B、Mo、Zn和Mn含量的平均值均低于全国平均值,全量Cu平均值高于全国平均值.有效B、Mo、Zn和Mn含量的平均值均低于临界值,有效Cu的平均值稍高于临界值;但66.7％的土样有效Cu含量低于临界值.硼、钼、锌和锰严重缺乏,铜多数缺乏.全场各类土壤的微量元素含量差异较大,各类土壤微量元素的垂直和水平分布特征不尽相同,尤其是垂直分布差异明显.从土壤微量元素的全量与母质的关系来看,以玄武岩、紫色砂页岩母质形成的土壤全量较高,砂砾岩母质形成的土壤全量中等,砂页岩和冲积物母质形成的土壤全量较低.     

不同母质发育的水稻土中铁、锰对甲烷排放的影响

盆栽结果表明,不同土壤类型铁、锰含量的差异是造成不同土壤类型间甲烷排放量差异甚大的重要因素之一。土壤中铁、锰通过对土壤氧化还原电位及根膜形成的影响而影响甲烷的排放。     

防洪物资储备决策方法初探

根据防洪抢险物资储备属于一种信息不全型决策问题的特点,本文提出了一种用于确定每年防灾物资准备量概率排序决策模型,并以孙不河流泥石流灾害预报火灾决策为例进行说明。     

环境监测用5种氯代烯烃混合气体标准样品研制

介绍了1μmol/mol氮气中5种氯代烯气体标准样品的研制方法。这5种氯代烯包括氯乙烯、1,1-二氯乙烯、顺1,2-二氯乙烯、三氯乙烯、四氯乙烯,其中氯乙烯常温下为气态,其他4种为液态,并且沸点低,将这几种氯代烯制备成气体标准样品存在制备精度低、气液转换不完全等困难。经研究,采用2步称量法制备5种氯代烯气体标准样品,重复制备的相对标准偏差小于1.6%。建立了5种氯代烯标准气体瓶内均匀性的实验方法,并通过考察样品量值伴随样品压力的变化来评价样品的均匀性。结果显示,5种氯代烯标准气体是均匀的,最低使用压力为1 MPa。依照ISO 15000.3来考察样品的时间稳定性,样品有效期为12个月。相对扩展不确定度为3%(置信度为95%)。     

Application of Defined Co-Immobilized Microbial Consortium as a Ready-to-Use Seed Inoculum in Bod Analysis

A number of microorganisms were isolated from sewage. Biochemical Oxygen Demand (BOD-5 day) analysis was carried out by individual pure cultures. The cultures giving higher or equal BOD values as compared to reference GGA solution were selected for the formulation of a defined mixed microbial consortium. This microbial consortium was co-immobilized on calcium-alginate beads. Four synthetic and six industrial samples were tested for BOD by using immobilized beads as well as sewage as source of seeding materials. BOD values obtained with beads for all the synthetic as well as industrial samples were fairly comparable with those obtained with sewage. Reusability of prepared microbial beads was also checked with different synthetic and industrial samples and was compared with reference GGA solution. The same microbial beads can be reused three times for different BOD-5 day estimations. It is recommended that immobilized microbial beads can be used as a ready-to-use seeding material for BOD analysis.     

Energy efficacy used to score organic refuse pretreatment processes for hydrogen anaerobic production

The production of hydrogen through Anaerobic Digestion (AD) has been investigated to verify the efficacy of several pretreatment processes. Three types of waste with different carbon structures have been tested to obtain an extensive representation of the behavior of the materials present in Organic Waste (OW). The following types of waste were selected: Sweet Product Residue (SPR), i.e., confectionary residue removed from the market after the expiration date, Organic Waste Market (OWM) refuse from a local fruit and vegetable market, and Coffee Seed Skin (CSS) waste from a coffee production plant. Several pretreatment processes have been applied, including physical, chemical, thermal, and ultrasonic processes and a combination of these processes. Two methods have been used for the SPR to remove the packaging, manual (SPR) and mechanical (SPRex). A pilot plant that is able to extrude the refuse to 200 atm was utilized. Two parameters have been used to score the different pretreatment processes: efficiency (ξ), which takes into account the amount of energy produced in the form of hydrogen compared with the available energy embedded in the refuse, and efficacy (η), which compares the efficiency obtained using the pretreated refuse with that obtained using the untreated refuse. The best result obtained for the SPR was the basic pretreatment, with η = 6.4, whereas the thermal basic pretreatment gave the highest value, η = 17.0 for SPRex. The best result for the OWM was obtained through a combination of basic/thermal pretreatments with η = 9.9; lastly, the CSS residue with ultrasonic pretreatment produced the highest quantity of hydrogen, η = 5.2.     

环境生物样品预处理中的微波溶样技术

微波溶样是近年产生的一种崭新的有前途的样品预处理技术，本文评述这一技术在环境、生物样品消解方面的近期应用。