Nanoencapsulation of hexavalent chromium with nanoscale zero-valent iron: High resolution chemical mapping of the passivation layer

Solid phase reactions of Cr(Ⅵ) with Fe(0) were investigated with spherical-aberration-corrected scanning transmission electron microscopy(Cs-STEM) integrated with X-ray energy-dispersive spectroscopy(XEDS). Near-atomic resolution elemental mappings of Cr(Ⅵ)–Fe(0) reactions were acquired. Experimental results show that rate and extent of Cr(Ⅵ) encapsulation are strongly dependent on the initial concentration of Cr(Ⅵ) in solution. Low Cr loading in nZⅥ(1.0 wt%) promotes the electrochemical oxidation and continuous corrosion of n ZⅥ while high Cr loading(1.0 wt%) can quickly shut down the Cr uptake. With the progress of iron oxidation and dissolution, elements of Cr and O counter-diffuse into the nanoparticles and accumulate in the core region at low levels of Cr(Ⅵ)(e.g., 10 mg/L). Whereas the reacted n ZⅥ is quickly coated with a newly-formed layer of 2–4 nm in the presence of concentrated Cr(Ⅵ)(e.g., 100 mg/L). The passivation structure is stable over a wide range of pH unless pH is low enough to dissolve the passivation layer. X-ray photoelectron spectroscopy(XPS) depth profiling reconfirms that the composition of the newly-formed surface layer consists of Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxides with Cr(Ⅵ) adsorbed on the outside surface. The insoluble and insulating Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxide layer can completely cover the n ZⅥ surface above the critical Cr loading and shield the electron transfer. Thus, the fast passivation of nZⅥ in high Cr(Ⅵ) solution is detrimental to the performance of nZⅥ for Cr(Ⅵ) treatment and remediation.     

Relationship between physicochemical properties and dewaterability of hydrothermal sludge derived from different source

Sewage sludge (SS) and deinking sludge (DS) were used to comparatively study the hydrothermal dewatering of sludge with different components. For a better overview, an insight into the relationship between physicochemical properties and dewaterability of hydrothermal sludge was provided. Results found that not all kinds of sludge were suitably conditioned by hydrothermal treatment (HT) in term of the elevation of dewaterability. Higher hydrothermal temperature tended to enhance the dewaterability of SS rather than DS, which was supported by the variation of their physicochemical properties (including water distribution, bonding energy, extracellular polymeric substance (EPS), particles size, acid functional groups and zeta potential in this study). In addition, the changes in surface morphology suggested that the reverse effect of HT on sludge dewaterability was mainly due to their dewatering behavior. For SS, the destruction of EPS structure leaded to the release of bound water, thereby strengthening sludge dewatering. Conversely, “Bridging effect” generated by lignocellulose in DS was beneficial for sludge dewatering; however, the increasing hydrothermal temperature degraded part of lignocellulose and weakened “bridging effect”, finally resulting in worse dewaterability of DS.     

可靠性强化试验技术在某型伺服作动器研制中的适用性探索

目的探索可靠性强化试验技术在典型机电液一体化产品伺服作动器研制过程中的适用性。方法以某型伺服作动器为研究对象,从故障激发的角度对可靠性强化试验技术的应用进行可行性分析,在响应调查和应力分析的基础上,结合产品的工作特点设计适用于该类伺服作动器的可靠性强化试验方案,包含低温步进应力试验、高温步进应力试验、快速温度循环试验10个循环、振动步进应力试验(包含气锤式三轴向六自由度超高斯随机振动方式及电磁振动台随机振动方式)及综合环境应力试验5个循环,并依此进行试验。结果在快速温度循环试验及综合环境应力试验过程中,均有效地激发出了产品的漏油故障,与相似产品外场暴露的漏油故障模式相吻合。结论可靠性强化试验技术可有效地应用于典型机电液一体化产品伺服作动器的研制过程,设计的可靠性强化试验方案可有效地激发外场出现频率较高的故障,可作为该类产品研制的试验手段之一。     

密封组合形式对结构密封性能影响研究

目的研究密封组合形式对结构密封性能的影响。方法开展密封性能试验,从密封形式、装配形式和涂覆形式的3种组合形式开展试验研究,找出结构密封性能影响因素,筛选密封最优组合形式。结果结构密封3种组成形式分别为有无贴合面的密封形式,干涉装配、湿装配形式,部分涂覆、全涂覆形式。开展2种应力水平下8种密封组合形式的密封性能试验,在保证密封工艺质量条件下,按照飞机结构和受载特点选取合理密封组合形式能有效提高结构密封性能。结论在飞机应力较高、不常拆的密封部位应选择贴合面密封、干涉装配、部分涂覆的密封组合形式,在飞机结构设计要求间隙装配、常拆卸的密封部位选择贴合面密封、湿装配、部分涂覆的密封组合形式。     

Desert Water Harvesting to Benefit Wildlife: A Simple, Cheap, And Durable Sub-Surface Water Harvester for Remote Locations

A sub-surface desert water harvester was constructed in the sagebrush steppe habitat of south-central Idaho, U.S.A. The desert water harvester utilizes a buried micro-catchment and three buried storage tanks to augment water for wildlife during the dry season. In this region, mean annual precipitation (MAP) ranges between about 150–250 mm (6″–10″), 70% of which falls during the cold season, November to May. Mid-summer through early autumn, June through October, is the dry portion of the year. During this period, the sub-surface water harvester provides supplemental water for wildlife for 30–90 days, depending upon the precipitation that year. The desert water harvester is constructed with commonly available, “over the counter” materials. The micro-catchment is made of a square-shaped, 20 mL. “PERMALON” polyethylene pond liner (approximately 22.9 m × 22.9 m = 523 m²) buried at a depth of about 60 cm. A PVC pipe connects the harvester with two storage tanks and a drinking trough. The total capacity of the water harvester is about 4777 L (1262 U.S. gallons) which includes three underground storage tanks, a trough and pipes. The drinking trough is refined with an access ramp for birds and small animals. The technology is simple, cheap, and durable and can be adapted to other uses, e.g. drip irrigation, short-term water for small livestock, poultry farming etc. The desert water harvester can be used to concentrate and collect water from precipitation and run-off in semi-arid and arid regions. Water harvested in such a relatively small area will not impact the ground water table but it should help to grow small areas of crops or vegetables to aid villagers in self-sufficiency.     

CTL-12型化学需氧量速测仪与标准法测定CODCr之比较

使用CTL—12型化学需氧量速测仪分析废水化学需氧量，简便、快速，且方法可行，完全能满足环境监测技术要求。     

Trace Metal Concentration in Roadside Surface Soil and Tree Back: A Measurement of Local Atmospheric Pollution in Abuja, Nigeria

Cadmium, copper, lead, nickel and zinc concentrations were analysed by atomic absorption spectrophotometry in surface soil and tree bark from different districts of Abuja, Nigeria, in order to determine the atmospheric trace metal input in the area.Elevated concentrations of some of the studied metals were observed in the soil and tree bark samples from the commercial/high traffic areas of the city compared to backgroundvalues. In soil samples, the average concentration of the metals were 0.6±0.4, 18.0±4.0, 281±39, 16±4 and66±23 g g^-1 dry weight for Cd, Cu, Pb, Ni and Zn, respectively, whilst the average concentrations in tree bark were 0.3±0.2, 12±4, 133±32, 13±3 and 61±10 g g^-1 dry weight for Cd, Cu, Pb, Ni and Zn, respectively. The trend in trace metal levels suggested that automobile emissions are a major source of these metals as the highest concentrations of Pb and Zn were recorded in the commercial areas of the city known for their high traffic densities. The levels of metal in the study area were relativelylow compared to levels found in some larger and older cities in various countries worldwide.     

Monitoring of Butter and Ghee (Clarified Butter Fat) for Pesticidal Contamination from Cotton Belt of Haryana, India

Butter (45) and ghee (55) samples were collected from rural and urban areas of cotton growing belt of Haryana and analysed for detecting the residues of organochlorine, synthetic pyrethroid and organophosphate insecticides. The estimation was carried out by using multi residue analytical technique employing GC-ECD and GC-NPD systems equipped with capillary columns. Butter samples were comparatively more contaminated (97%) than ghee (94%), showing more contamination with organochlorine insecticides from urban samples. About 11% samples of butter showed endosulfan residues above MRL value and 2% samples had residues of synthetic pyrethroids and organophosphates each above their respective MRL values. In ghee, residues of HCH & DDT both and of endosulfan exceeded the MRL values in 5 and 20% samples, respectively. Among organophosphates, only chlorpyriphos was detected with 9% samples showing its residue above MRL value. Irrespective of contamination levels, residues above the MRL values were more in ghee. More extensive study covering other agricultural regions/zones of Haryana has been suggested to know the overall scenario of contamination of milk products.     

Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.     

Prediction of Leachate Level in Kimpo Metropolitan Landfill Site by Total Water Balance

Kimpo metropolitan landfill has received various kinds of wastessince January 1992. The leachate level was measured to be 10.3 m in May 1995 and the level increased to 12.2 m in August 1996. Therefore, to prove the reason for the increasing leachate level, we calibrated hydraulic conductivity of each waste andintermediate layer using the HELP (Hydrologic Evaluation ofLandfill Performance) model. The leachate generation data measured from February 1993 to October 1995 was used in the model calibration. As a result of a model calibration, we obtained anaverage infiltration ratio and used this in analysis of the total water balance to predict elevation of leachate level. Main causes of the elevation of the leachate level were the high water content of the waste and the degradation of the leachate-drainage system caused by the subsidence of a naturalbarrier layer.