废弃印刷线路板碘化法浸金研究

针对碘化法从废弃印刷线路板中提取金的工艺设计,分别考察了碘的质量分数、n(I₂)/n(I^-)比值、固液比、双氧水的质量分数、pH值、浸出时间和浸出温度对金浸出率的影响。结合正交设计优化实验方法,提出了从废弃印刷线路板中碘化法浸取金的最佳工艺条件：碘的质量分数为1.1％,n(I₂)∶n(I^-)=1∶10,双氧水的质量分数为1.5％,浸出时间4 h,固液比为1∶10,浸出温度为常温（25℃）,溶液pH值为中性,此时金浸出率可达97.5％。     

基于生态安全的DAT-IAT城市污水处理工艺改进研究

通过正交试验,得到了DAT-IAT工艺和A/DAT-IAT工艺处理城市污水的常规指标去除和生态毒理指标削减的最优运行条件。结果表明,在正交试验的同一工艺中,COD去除最优运行条件的出水COD值优于生态毒性削减最优运行条件的出水COD值,但前者出水的生态毒性较大。由于厌氧池的水解酸化作用,A/DAT-IAT工艺对COD和生态毒性的处理效果均优于DAT-IAT工艺,并且回流总能耗低于DAT-IAT工艺,但是出水COD仍不达标。为了降低进入工艺的COD的总量,以絮凝沉淀做为预处理工艺,并采用Al残留量最小的絮凝剂投药量以降低出水中残留Al带来的生态风险。结果表明,在COD去除最优运行条件下,具有絮凝预处理的工艺对COD的去除效果优于没有絮凝预处理的工艺。絮凝-A/DAT-IAT工艺在COD去除最优运行条件下出水COD为104.46 mg/L,满足排放标准。在毒性削减最优运行条件下,具有絮凝预处理的工艺的出水生态毒性有所上升,但是污染物的总量得到了大幅削减。絮凝-A/DAT-IAT工艺与DAT-IAT工艺相比,在污染物去除效率得到大幅增加的同时,生态毒性得到有效控制,生态安全得到了有效的保障。     

微曝气Fenton氧化法处理模拟双酚A废水的效果及其生物验证

研究了微曝气Fenton氧化法关键工艺参数对模拟双酚A（BPA）废水处理效果的影响,并从活性污泥性质和污染物去除率两方面,采用膜生物反应器(membrane bioreactor, MBR)对微曝气Fenton氧化法的处理效果进行了实验验证,为实现BPA废水的生物处理奠定基础。结果表明,初始pH值、反应时间、H₂O₂/COD(质量浓度比)、H₂O₂/Fe²⁺ (摩尔浓度比)、反应温度及曝气量均对预处理效果有较大影响,在最佳条件下,COD去除率可达70%,BOD/COD值则由原废水的0.02提高到0.50以上。MBR处理上述出水的结果表明,经微曝气Fenton氧化处理BPA的废水,可较好地适应后续的生化处理。     

高锰酸钾降解地下水中PCE的研究

以氯代有机污染物中常见的PCE为目标污染物,以自制高锰酸钾溶液为氧化剂,采用批实验方法,探讨了高锰酸钾降解PCE的反应动力学、影响因素以及反应机理。反应结果表明,高锰酸钾降解PCE的反应符合一级动力学方程,反应活化能E为57.119 kJ/mol,在30℃条件下,反应速率常数为0.0076 min^-1,半衰期为91.20 min。在pH在3～10,离子强度在0～0.1030 mol/L之间变化时,反应速率不受明显影响。     

超细粉煤灰基成型吸附剂的动态吸附实验

以粉煤灰为原料制备成型吸附剂,对水溶液中亚甲基蓝和Cr⁶⁺进行动态吸附研究,绘制穿透曲线,利用Origin软件对实验数据分析处理,得出穿透曲线的通式C_t=A₁－A₂〖〗1+(t/t₀)^p+A₁。结果表明,初始浓度C₀=25 mg/L,填料高度不同时,达到穿透点的时间随填料高度的增加而增加;填料高度h=200 mm,初始浓度不同时,达到穿透点的时间随初始浓度的增加而减小;该吸附剂对有机染料和重金属离子均有较好的吸附性能;穿透曲线通式的回归线性相关系数表明,该通式可很好地反映超细粉煤灰成型吸附剂的动态吸附过程。     

太阳光Fenton法处理垃圾渗滤液中有机污染物

研究利用太阳光Fenton法处理垃圾渗滤液。根据太阳光辐射强度随时间的变化规律,选择重庆7、8月份的晴天,在中午12：00到下午14：00时进行试验,研究太阳光辐射时间、pH值、Fenton试剂用量对垃圾渗滤液COD去除率的影响。研究结果表明：太阳光Fenton法对垃圾渗滤液的COD有较好的去除效果,COD去除率达86.2%。太阳光Fenton法处理垃圾渗滤液的优化条件是：日光辐射时间为120 min,pH值为2.5,Fe²⁺浓度为5 mmol/L,H₂O₂浓度为570 mmol/L。同时,论文还对太阳光Fenton法处理垃圾渗滤液的动力学进行分析。研究结果显示：太阳光Fenton法处理垃圾渗滤液,其表观动力学方程为-dC/dt=2.6×10^-8×P^1.92×F^1.79×E^1.67。     

基于超临界水氧化过程的能源环境系统设计

阐述了超临界水氧化过程的工艺路线,介绍了超临界水氧化过程的特点,提出了基于超临界水氧化过程的能源环境系统,设计了几种热量与能量回收系统程的耦合工艺,为提高超临界水氧化过程的经济性奠定了基础。     

厌氧序批式反应器内挥发性脂肪酸积累特性研究

小试规模的厌氧序批式反应器（ASBR）,通过人工配水,研究了启动3个月时间以及一个运行周期内反应器内挥发性脂肪酸（VFA）的积累情况,并通过分析期间产甲烷活性的变化说明了控制VFA积累的重要性。经过近120 d的运行,乙酸和丙酸的最大比产甲烷活性分别提高了1.8和2.2倍,说明反应器的启动过程即是微生物群落的优化和选择的过程,ASBR的抗冲击的能力较强说明随启动的进行和种群的优化,活性污泥凝聚性能增强,对VFA的降解能力增强。     

Modeling potential herbicide loss to surface waters on the Swiss plateau

Lack of sufficiently detailed data often limits the applicability of complex transport-reaction models for estimating potential herbicide loss to surface waters. Therefore, there is also a need for simple models that are easy to apply but still capture the main features of the underlying processes.In this study, a simple regression model was developed to assess the vulnerability of catchments in the Swiss Plateau to diffuse herbicide loss to surface waters. The model is designed as a screening tool to rank the catchments in a relative sense and not to calculate Predicted Environmental Concentrations (PEC) of pesticides. The main goal is to capture two dominating factors controlling diffuse herbicide transport into streams and rivers. These factors are herbicide application and fast flow processes that are mainly responsible for herbicide transport. In a first step vulnerability of sites to herbicide loss is estimated based on site-specific conditions irrespective of actual herbicide application. In the second step, this vulnerability assessment is combined with actual herbicide application data to estimate the potential herbicide loss.The fast flow index (FFI), derived from discharge data using a base flow separation method, was applied as a proxy for the amount of fast flow occurring. The influence of catchment attributes (including topographic, climatic and soil data) on the FFI was analyzed using a multiple regression approach based on data from 57 catchments of the Swiss Plateau. By combining regression analysis with mechanistic knowledge, a two factor non-linear model based on river density and soil permeability as dominant input factors was selected as the best model for FFI prediction given the available data. Higher dimensional models had to be excluded because the strong correlation between the potential input factors led to unrealistic dependences while only minimally improving the quality of the fit.The spatial pattern of the predicted FFI as a measure for the vulnerability to diffuse herbicide losses shows a clearly increasing trend from the western to the eastern part of the Swiss Plateau and towards the pre-alpine/alpine regions in the south.In general the pattern of herbicide use corresponds to site conditions typical of a low FFI. However, the spatial analysis revealed exceptions, namely areas in which high actual herbicide use coincides with a high FFI.Despite the uncertainties in the model, this simple approach seems to be useful for supporting site-adapted agricultural practice whenever the higher accuracy of more detailed models is not required or too expensive to achieve. In addition, in combination with data on actual herbicide application, it can support the design of monitoring strategies by identifying critical areas of actual herbicide loss.     

Batch sorption dynamics and equilibrium for the removal of lead ions from aqueous phase using activated carbon developed from coffee residue activated with zinc chloride

Lignocellulosic materials are good precursors for the production of activated carbon. In this work, coffee residue has been used as raw material in the preparation of powder activated carbon by the method of chemical activation with zinc chloride for the sorption of Pb(II) from dilute aqueous solutions.The influence of impregnation ratio (ZnCl₂/coffee residue) on the physical and chemical properties of the prepared carbons was studied in order to optimize this parameter. The optimum experimental condition for preparing predominantly microporous activated carbons with high pore surface area (890 m²/g) and micropore volume (0.772 cm³/g) is an impregnation ratio of 100%. The developed activated carbon shows substantial capability to sorb lead(II) ions from aqueous solutions and for relative impregnation ratios of 75 and 100%, the maximum uptake is practically the same. Thus, 75% represents the optimal impregnation ratio.Batch experiments were conducted to study the effects of the main parameters such as contact time, initial concentration of Pb(II), solution pH, ionic strength and temperature. The maximum uptake of lead(II) at 25 °C was about 63 mg/g of adsorbent at pH 5.8, initial Pb(II) concentration of 10 mg/L, agitation speed of 200 rpm and ionic strength of 0.005 M. The kinetic data were fitted to the models of pseudo-first order and pseudo-second order, and follow closely the pseudo-second order model. Equilibrium sorption isotherms of Pb(II) were analyzed by the Langmuir, Freundlich and Temkin isotherm models. The Freundlich model gives a better fit than the others.Results from this study suggest that activated carbon produced from coffee residue is an effective adsorbent for the removal of lead from aqueous solutions and that ZnCl₂ is a suitable activating agent for the preparation of high-porosity carbons.