基于ELPI的南京城区大气可吸入颗粒物现状分析

采用电称低压冲击器(ELPI)对南京城区可吸入颗粒物粒径分布和质量浓度进行连续在线测量,得到了南京城区大气可吸入颗粒物的日变化特征,表明其呈现双峰、双谷分布,夜间高,白天低,上午高,下午低;结合气象参数,研究了大气可吸入颗粒物浓度变化与气象因子的相关性;此外,对可吸入颗粒物粒径分布特征也进行了研究,可以看出,南京地区可吸入颗粒物的主要成分是细颗粒(PM2.5),粒径在0.028～2.31μm的颗粒物占可吸入颗粒物的98%～99%。     

一种计算粒子电迁移率的新模型

近几年来,粒子电迁移率引起了更多学者的注意。因为它是表征带电粒子在电场中运动的重要参数之一。在这方面,人们已作了大量的研究工作,提出了一些计算粒子电迁移率的理论和半经验模型。基于前人的研究,本文提出了一种计算粒子电迁移率的新模型,并用前人的实验结果和本研究的实验结果对此模型进行了检验。计算结果和实验数据很吻合。就某种意义上讲,此模型是对以前模型的扩展和改进,它可广泛应用于溶胶的研究和工业应用。     

Compression Molding of Phenolic Resin and Corn-based DDGS Blends

With the rapid growth in the ethanol fuel industry in recent years, considerable research is being devoted to optimizing the use of processing coproducts, such as distillers dried grains with solubles (DDGS), in livestock diets. Because these residues contain high fiber levels, they may be amendable to incorporation into bio-based composites. Thus, the goal of this study was to demonstrate the viability of using corn-based DDGS as a biofiller with phenolic resin, in order to produce a novel biomaterial. DDGS was blended with phenolic resin at 0, 10, 25, 50, 75, and 90%, by weight, and then compression molded at 51 MPa (3.7 tons/in²) and 174 °C (345°F). Molded specimens were then tested for tensile strength. Tensile yield strengths ranged from 32 MPa (4,700 psi) to 7.6 MPa (1,100 psi), while the engineering strain ranged from 0.6% to 1.25%. Results indicate that DDGS concentrations between 25% and 50% retained sufficient mechanical strength and thus represent reasonable inclusion values. Additionally, data were similar to those from other studies that have investigated biofillers. Follow-up studies should quantify the effects of altering molding parameters, including molding pressure, temperature, and time, as well as pretreatment of the DDGS. Additionally, strength of the DDGS composites should be optimized through the use of coupling agents or other additives. Mention of a trade name, proprietary product, or specific equipment does not constitute a guarantee or warranty by the United States Department of Agriculture and does not imply approval of a product to the exclusion of others that may be suitable.     

兆欧表的禁忌分析与防范措施

通过对电气领域的电气安全问题长期研究以及对测试工作中经验、教训的总结,针对兆欧表在电气领域应用中的十六种不正确、不妥当的使用方法,对其错误及危害性逐项进行分析探讨,并提出了相应的改进办法及防范措施。实践表明,这些改进办法及防范措施在电气技术工作和安全生产管理中具有一定的实用价值。     

Influence of workpiece materials on aerosol emission from die sinking electrical discharge machining process

Simultaneous investigation of environmental emissions and machining aspects of electrical discharge machining process is essential for achieving hygienic and efficient machining. The main objective of the present work is to experimentally investigate and analyze the aerosol emission rate and the material removal rate from a die sinking electrical discharge machining process for three commonly used work piece materials viz., tool steel, mild steel and aluminum using Taguchi methodology of Experimental Design in order to suggest suitable process conditions for green manufacturing. The aerosol emission profile of all workpiece materials was found to be closely related to the material removal profile. A significant variation in emission and material removal rate was observed for workpiece materials which may be accorded to the variation in melting and vaporization temperatures. It was also observed that majority of aerosol constituents evolved from workpiece materials and that the constituents with low melting points were having high relative concentration in the aerosol emitted. The study introduced a parameter, the relative emission rate for comparing the emission for various process parameters and workpiece–tool material combinations. The favorable machining parameters for each material were then identified by employing signal to noise ratio analysis of the relative emission rate.     

基于Bayes判别模型的火场中铜导线短路熔痕 定量金相鉴定方法研究

借助计算机图像处理技术,改进了定量金相分析方法,测量了20个一次短路熔痕和20个二次短路熔痕的金相组织,对数据进行了主成分分析,提炼出了晶粒特征因子、气孔特征因子和复合因子三个主成分,基于Bayes判别法建立了火场中短路熔痕定量金相分析判别模型,经自身检验和交互检验,准确率均高于80%,充分满足鉴定要求,为更加有效地应用定量金相法鉴别短路熔痕提供了理论依据。     

填埋场衬层渗漏的电学法检测研究进展

综述了几种常用的填埋场渗漏检测方法,指出电学法已成为填埋场不同运行阶段（施工期和运营期）渗漏检测的主流方法。分析了各阶段电学检测方法的适用条件和优缺点,在防渗膜铺设阶段,常利用双电极法或电极-偶极子法进行施工完整性检测;在填埋场运营期间,根据场地实际情况可以选择电极格栅法、基于物联网的监测预警云平台、阵列式偶极子法或高密度电法进行膜渗漏检测及长期监测。     

材料以及产品的环境试验方法

本文主要分析了各环境因素及其引起的失效模式,介绍了环境试验方法以及环境试验设计过程中应当注意的问题等基础知识,还给出了一些常用的环境试验标准.     

不同方法对南方几种土壤阳离子交换性质的测定比较

分別采用1mol L~(-1) NH_4OAC淋洗法,0.1mol L~(-1)BaCl_2捕掳交换法,6.667×10~(-3)mol L~(-1)Co(NH_3)_6Cl_3提取法以及电荷测定法测定了南方几种不同性质的土壤的阳离子交换性质。结果表明,酸性土壤的阳离子交换量具有不定性,NH_4OAC法的结果很高,而其它方法的结果显著偏低,但方法间仍存在显著差异。不过,各法对微酸性、中性土壤的测定结果无显著差异。与NH_4OAC法相比,BaCl_2法得到较多的Ca,而Co法则交换出较少的K。各法的浸提液pH间虽存在差异,但彼此间有良好的统计相关性。Co法测定的CEC值与交换性阳离子总和较为吻合,其浸提液pH与pH_(KCl)、pH_(CaCl_2)有良好的线性关系。看来,不同方法对酸性土壤阳离子交换量的测定差异主要来自測定过程中介质pH条件及离子强度不同所浸出的交换性酸的多寡。本文认为,Co(NH_2)_6Cl_3法可以作为这些土壤阳离子交换性质测定的例行方法。     

流动缩旋紫铜筒体的试验分析

此文论述了紫铜结晶简休流动缩旋成形的试验过程.采用流动旋压缩旋筒形件的试验研究,实现了以减径为主的缩谈成形,旋出了满足紫铜结晶器精加工要求的大直径厚壁筒体.通过利用三向投影接触面积和三向旋压分力的计算分析,并与变薄旋压变形相比较,对流动缩旋有了一定的了解,探讨了流动旋压方式进行普通旋压变形的工艺过程.