原状黄土的反压饱和法试验研究

含水量是黄土液化特性研究中的一个至关重要的参数,对原状黄土进行充分饱和是饱和黄土动三轴试验中一个不可回避的课题。以WF公司生产的WF12440型空心圆柱扭剪仪为实验平台,运用反压饱和法,对室内原状黄土进行了饱和试验研究。该仪器提供3种不同加压方式增加围压和反压(孔压),即手动加压、自动加压和线性持续加压,通过检测孔隙压力系数B值是否达到0.95以上来判断黄土是否完全饱和。试验表明,即便是初始饱和度较低的原状黄土,也可以采用反压饱和法,在较短的时间内使孔压系数B值达到0.95以上,实现完全饱和,具体可以采用线性连续加压方式;初始压力差,即围压和反压之差一般可设为10 kPa,起始围压也设为10 kPa,太大或太小都会对试样造成破坏;如果孔压在1分钟内的变化值小于围压和反压之间压力差的5%,则认为孔压稳定,即可进行B值检测。     

实行年度目标考核是促进监测工作发展的有效方法

实行年度目标责任制考核 ,为监测站的改革和发展找到了一条有效途径。文章通过对年度目标考核责任制的方式、方法及实施后所取得成效的介绍 ,为监测站的改革与发展提供了借鉴     

Predicting bicycle helmet wearing intentions and behavior among adolescents

INTRODUCTION: Cycling accidents in Australia, especially those resulting in head injuries, are a substantive cause of death and disability; but despite legislation and evidence that helmets reduce the risk of head injury, few adolescents wear them. METHOD: This study employed a revised version of the Theory of Planned Behavior (TPB; [Ajzen, I. (1991). The theory of planned behavior. Organizational Behavior and Human Decision Processes, 50, 179-211]) to investigate the determinants of helmet use among a sample of adolescents. Participants in the initial data collection were 294 high school students in Year 8 and Year 11, with 266 completing a follow-up questionnaire measuring behavior over the previous two weeks. RESULTS: Social norms, perceptions of control, and past behavior significantly predicted intentions to use helmets and perceptions of control and past behavior predicted actual helmet use. CONCLUSIONS: Strengthening the routine of helmet use and building young people's confidence that they can overcome any perceived barriers to helmet use will improve adherence to helmet wearing behavior.     

Exploring the dark side of organizational citizenship behavior

In recent years, there has been increasing interest in positive organizational scholarship in general, including positive organizational behavior (POB) in particular. This work identifies organizational citizenship behavior (OCB) as a prototypical POB. Conceptualizing OCBs in this way is sensible in light of more than 30 years of research highlighting the desirable aspects of such behavior. At the same time, some researchers have raised questions about positive organizational scholarship and have called for a more balanced view of ostensibly positive behaviors. The purpose of this paper, then, is to take a more nuanced view of OCBs while highlighting the dark side of citizenship behavior. In doing so, we review conceptual and empirical work that has challenged the idea that OCBs are inherently positive. We also discuss research that seeks to develop a deeper understanding of the conditions under which OCB does more harm than good. Finally, important areas for future research and the practical realities facing scholars who seek to publish research investigating the dark side of citizenship are addressed as well. Copyright © 2012 John Wiley & Sons, Ltd.     

Force-Velocity Characteristics of Individual Human Skeletal Muscles: TBCIat and TBCIong. Outline of the Method

The aim of the work is to outline a procedure of finding force-velocity (F–V) characteristics (F = f(V)) of individual skeletal muscles of the human locomotor system. The presentation is based on an example concerning extensors of the elbow joint: the lateral and long heads of triceps brachii (TBCIat and TBCIong). The experimental part of the procedure involves a natural movement of using the upper extremity to push an external object of variable, adjustable load, engaging both the elbow and shoulder joint.

Five men aged 23 took part in the experiment. Their task was to push the handle of a physical pendulum whose moment of inertia could be adjusted within the range of 58 kg m²-450 kg m², so as to give it maximum angular velocity. During each trial the movement of the trunk, of the upper extremity and of the pendulum was video recorded and the force applied with the hand to the handle of the pendulum was measured.

In order to find the F–V characteristics a simulation model SHOULDER was used, which is capable of solving the synergy problem for muscles of the arm and the shoulder girdle.

It was found that despite considerable dispersion of experimental points the respective regression lines revealed a clear tendency of decreasing muscle force for increased shortening velocity of the monoarticular head (TBCIat) and of increasing muscle force for increased lengthening velocity of the biarticular head (TBCIong) of the triceps brachii muscle.     

Effect of Sweating on Insulation of Footwear

The study aimed to find out the influence of sweating on footwear insulation with a thermal foot model. Simultaneously, the influence of applied weight (35 kg), sock, and steel toe cap were studied. Water to 3 sweat glands was supplied with a pump at the rate of 10 g/hr in total. Four models of boots with steel toe caps were tested. The same models were manufactured also without steel toe. Sweating reduced footwear insulation 19–25% (30–37% in toes). During static conditions, only a minimal amount of sweat evaporated from boots. Weight affected sole insulation: Reduction depended on compressibility of sole material. The influence of steel toe varied with insulation. The method of thermal foot model appears to be a practical tool for footwear evaluation.     

Occupational Health and Social Resources

There is a relationship between the changes in work-related diseases and the following factors: the transformation of the organization of work, organizational development, as well as human and social changes in the work environment. These factors also influence the maintenance of industrial health and safety standards at work. Safety technology will continue to be important, but will be reduced in significance compared to the so-called soft factors, that is, all dimensions and parameters affecting people’s health and social environment at the work place.

It seems that in the future the relationship between the social resource development and work protection will become more relevant. Social resource development influences the quality of work performance and motivation, the quality of work and work protection, the likelihood of accidents and breakdowns, and the level of self-control and capacity of change.

The consequences of work protection research will be discussed in this article with a focus on the contribution of social sciences.     

Ergonomic Diagnosis of the Driver’s Workplace in an Electric Locomotive

This paper deals with research aimed at developing a method for ergonomic analysis of the driver’s workplace in an electric locomotive. It presents the structure of the diagnosis and its assumptions, and includes a re-evaluation of the questionnaire-expert method in ergonomic research. The article presents research data on weights and evaluations including their standard deviations for particular priority features. Ergonomic levels of the studied operator’s cabin in locomotives are compared.     

Synergy Between Visual and Auditory Signals and Its Influence on the Follow-Up Regulation Quality

The study aimed at verifying a hypothesis that supporting a visual signal of regulation deviation with an auditory one could improve the quality of regulation; the operator would have better information on machine operation. A special simulator was applied to follow-up tracking with a manual lever which controlled vertical movements of a cursor on a monitor screen. Simultaneously with visual information on screen, the operator was provided with an auditory deviation signal of pre-determined characteristics. 33 young males underwent the test. It was found that supporting a visual signal with an auditory one resulted in an improvement in the regulation quality by 5-6%, which proved synergy between those signals. The results may be used in designing tele- and servo-mechanisms, especially for remote control machinery, e.g., inspection robots or micromanipulators controlled by operators in a follow-up system.     

Simulation of Reflected and Scattered Laser Radiation for Designing Laser Shields

This paper presents a computer simulation of reflected and scattered laser radiation for calculating the angle of laser shields performed with the Laser Shield Solver computer program. The authors describe a method of calculating the shield angle for laser shields which protect workers against reflected and scattered laser radiation and which are made from different materials. The main assumptions of the program, which calculates and simulates reflected laser radiation from any material and which can be used for designing shield angles, are presented. Calculations are compared with measurements of reflected laser radiation. The results for one type of laser and different materials which interacted with a laser beam showed that the Laser Shield Solver was an appropriate tool for designing laser shields and its simulations of reflected laser radiation distribution have practical use.