The evolution of flame length for the oil tank fire with different top cover widths and lip heights

This study presents a quantitative analysis and interpretation of the variation in oil tank fire flame lengths for different oil tank sizes, top cover widths, and horizontal air flow velocities. The experimental results show that, at first, the flame length rises slowly with an increase in air flow speed. Then, once over a critical speed (0.6 m/s), the flame length decreases significantly with a further increase in air flow speed. Based on the characteristic length, a new dimensionless heat release rate is obtained, allowing the correlation between flame length, air flow speed, and dimensionless heat release rate to be calculated, which can be used to predict the flame length of an oil tank fire under different air flow speeds, lip heights, and cover widths.     

燃烧假人测试系统及其应用前景

燃烧假人测试系统是国际公认的定量评估防护装备阻燃性能的专用设备，本文主要介绍了燃烧假人测试系统的研究现状、系统构成、技术体系及应用前景。     

气相色谱——火焰光度法测定废水中黄磷的方法研究

研究了以苯为萃取剂，用气相色谱－－火焰光度法测定废水中的微量黄磷。结果色谱分离良好，萃取率大于９４％，水样易于保存，溶剂和杂质不干扰测定，水样加标回收率大于８８．４８％，精密度重复测定的变异系数不大于３．２％，定性检出限为２μｇ／Ｌ，定性检出限为６μｇ／Ｌ。     

聚乙烯塑料类固体废弃物热裂化研究

在反应温度455-495℃,氢气压力0.1～4.0MPa和反应时间2～12h的范围内,就聚乙烯塑料类固体废弃物热裂化时温度、压力和反应时间的影响以及不同反应条件下产物的碳数分布、馏程变化进行了探讨,得出适合于生产柴油馏分的反应条件是温度475℃,常压或低压,反应时间4h等。     

地表水中痕量金属元素的原子吸收法测定

采用单缝石英管技术作为火焰原子化器的原子捕集阱,以火焰法测定地表水中Cu、Pb、Zn、Cd等痕量元素,进一步提高了石英管法的灵敏度。依上述元素的顺序,其方法的最低检出浓度分别为4.0、10.0、1.0、1.0μg·l~(-1);对不同浓度标准溶液的精密度实验,其变异系数分别为0.5％、0.6％、1.6％、0.4％;对地表水加标回收率试验结果分别为95％—106％、100％—105％、95％—109％、84％—99％。     

废旧塑料的处理工艺

介绍了当前国内外几种处理和利用废旧塑料的方法，特别对废旧塑料掩埋、再生、回收焚烧、热裂解制造燃料油和化学品的技术和存在的问题作了重点探讨。     

灰化-火焰原子吸收法测定人发中的金属元素

讨论了人发中元素测定的前处理条件，并采用灰化－火焰原子吸收法测定了人发中锌，铜，铁，钙和镁５种金属元素的含量。     

废弃塑料生产涂料的工艺研究

本文主要介绍以废弃塑料为原料生产涂料的工艺技术，使整个城市生活垃圾的处理跃上一个新台阶，达到生活垃圾无害化、资源化的环保目标。     

废塑料裂解生产原料油的研究

本文对聚乙烯和聚丙烯的混合物裂解成原料油进行了研究 ,在 44 0℃条件下 ,不同比例的聚乙烯和聚丙烯被裂解。结果发现 ,聚丙烯有最高的液体回收率。几种催化剂被应用到聚丙烯的裂解过程中。裂解产品组分的构成及催化剂的选择是本研究的主要内容。通过比较几种不同催化剂的催化结果发现 ,复合催化剂有更好的催化效果。本研究为将来的废塑料综合利用提供了一种新的有用方法     

PBDF and PBDD from the combustion of bromine containing flame retarded polymers: A survey

The formation of polybrominated dibenzofurans (PBDF) and dibenzodioxins (PBDD) during the pyrolysis of different polymers containing brominated organic flame retardants was investigated. The pyrolyses were conducted at two different temperatures (600°C and 800°C) using three different oven configurations. Both the pyrolysis gases and the solid residues were analysed for PBDF and PBDD.

PBDF were found in almost all samples, but both the concentration and the degree of bromination varied greatly. The largest yields of PBDF in the percent range were measured in the pyrolysis products of polymers containing brominated diphenyl ethers. The other flame retardants generally yielded only a few ppm of PBDF. PBDD are formed only in a few samples and related to the PBDF in very low concentrations.