人工片状钙基脱硫剂的试制及其性能研究

介绍了用于沸騰炉燃煤锅炉脱硫的人工片状钙基脱硫剂的生产工艺,并用固定床反应器、压汞仪,扫描电子显微镜、强度仪等研究了该脱硫剂的物理化学特性。实验表明,采用该工艺生产的脱硫剂具有良好的抗压抗磨强度和耐水性,由于具有合理的孔分布,其固硫能力是石灰石的2—3倍,钙利用率可达40％,适用于850℃—1000℃的较宽温度范围。在3台沸腾炉共7个工况下的工业实验证明了该脱硫剂的上述特性。     

垃圾渗滤液预处理工艺的研究

本文结合工程实例,对生活垃圾焚烧发电厂垃圾渗滤液进行预处理工艺的研究,结果表明,预处理单元在垃圾焚烧厂渗滤液的整个处理系统中具有重要的作用和地位,渗滤液中部分污染物和无机离子能在预处理单元中得到较好的去除,在一定程度上减轻后续处理工艺的负荷。     

废FCC催化剂对水中铅离子的连续吸附及脱附

通过测定吸附等温线，考察了Ｐｂ２＋在废ＦＣＣ（流化催化裂化）催化剂上的吸附性能及规律，结果表明，Ｐｂ２＋在废ＦＣＣ催化剂上的吸附规律可用Ｌａｎｇｍｕｉｒ和Ｆｒｕｎｄｌｉｃｈ模式描述，吸附呈单分子层形式且容易进行。又通过填充床吸附试验，对Ｐｂ２＋的连续吸附及脱附情形作了考察。结果表明，在温度为１５℃、ｐＨ为５．１３、过柱速率为３．０ｍＬ／ｍｉｎ、径高比为２．２５．０条件下，吸附柱具备适宜的生产周期，连续吸附操作可行，柱效率可达７５．９％；在温度为１５℃、采用２ｍｏｌ／Ｌ稀盐酸作脱附剂，过柱速率为５．０ｍＬ／ｍｉｎ的条件下，吸附剂易于脱附再生，脱附效率可达７８．１％     

Enhanced struvite recovery from wastewater using a novel cone-inserted fluidized bed reactor

The feasibility of struvite recovery at low （12.5 mg/L） and high （120 mg[L） phosphorus concentrations was studied by constructing a novel fluidized bed reactor with cones （FBRwc） and without cones （FBRwoc）. The crystallization process was continuously operated for 133 days under different hydraulic retention times （HRT = 1-10 hr）, pH （7.5-10）, and molar ratios of Mg/P （0.75-1.75）, N/P （1-10） and Ca/Mg （0-2）. The optimum operating conditions of HRT, pH, Mg/P and N/P molar ratios were found to be 2 hr, 9, 1.25, and 7.5, respectively. Under these optimum conditions, the phosphorus precipitation efficiencies of FBRwc were 93% for low and 98% for high phosphorus influent; however, the efficiencies were 78% and 81% for FBRwoc, respectively. Due to crystal losses at each junction （17%-31%）, the crystal recovery efficiency of FBRwoc was relatively low （47%-65%） for both influent concentrations. However, the losses were minimal in FBRwc, which showed 75% and 92% crystal recovery for low and high phosphorus concentrations, respectively. At low calcium concentration, crystal chemical analysis showed the product to be pure struvite （〉 99%）. The scanning electron microscope and X-ray diffraction results further confirmed that the crystal recovered from FBRwc contained pure struvite, which could be considered a high quality fertilizer. Except HRT, all parameters （pH, Mg/P, N/P and Ca/Mg） were found to be influencing factors for FBRwc performance. Overall, inserting cones in each part of the reactor played a significant role in enhancing struvite recovery from a wide range of phosphorus-containing wastewater.     

Turbosorp湍流吸收循环流化床烟气脱硫技术在改造工程中的应用

循环流化床半干法烟气脱硫技术是目前世界上主流脱硫工艺技术之一,主要适用于大中型燃煤电厂的烟气脱硫,在国内外拥有大量成功运行的工程案例。本文章基于本公司实践论述Turbosorp湍流吸收循环流化床脱硫技术的技术特点、关键工艺控制要点以及在机组改造工程中的技术优势,为同类型机组改造工程中的方案选择提供参考。     

Emissions of SO2, NO and N2O in a circulating fluidized bed combustor during co-firing coal and biomass

This paper presents the experimental investigations of the emissions of SO2, NO and N2O in a bench scale circulating fluidized bed combustor for coal combustion and co-firing coal and biomass. The thermal capacity of the combustor is 30 kW. The setup is electrically heated during startup. The influence of the excess air, the degree of the air staging, the biomass share and the feeding position of the fuels on the emissions of SO2, NO and N2O were studied. The results showed that an increase in the biomass shares resulted in an increase of the CO concentration in the flue gas, probably due to the high volatile content of the biomass. In co-firing, the emission of SO2 increased with increasing biomass share slightly, however, non-linear increase relationship between SO2 emission and fuel sulfur content was observed. Air staging significantly decreased the NO emission without raising the SO2 level. Although the change of the fuel feeding position from riser to downer resulted in a decrease in the NO emission level, no obvious change was observed for the SO2 level. Taking the coal feeding position R as a reference, the relative NO emission could significantly decrease during co-firing coal and biomass when feeding fuel at position D and keeping the first stage stoichiometry greater than 0.95. The possible mechanisms of the sulfur and nitrogen chemistry at these conditions were discussed and the ways of simultaneous reduction of SO2, NO and N2O were proposed.     

生物流化床短程硝化的快速启动及影响因素研究

采用内循环生物流化床反应器处理模拟高浓度氨氮废水,以确定其对处理高浓度氨氮废水的可行性,同时对试验条件进行了优化。结果研究表明:控制温度为(31±1)℃,利用反应器自身流化所携带溶解的空气,反应器内DO值可维持在1.5~2.5 mg/L,调节pH为8.0~8.5。经过42 d的污泥驯化适应时期,进水氨氮(NH4+-N)浓度由50 mg/L提高到300 mg/L。由于流化床采用填料载体微生物膜与活性污泥双重作用,同时载体呈流化状态,接触均匀,有巨大的比表面积,可以使床内保持高浓度的生物量,从而达到高效快速的传质效果。在HRT由开始的16 h缩短到8 h的条件下,氨氮(NH4+-N)的去除率达到90%以上,亚硝氮(NO2--N)的积累率达到75%。且在以后30 d的稳定运行阶段,氨氮(NH4+-N)去除率和亚硝氮(NO2--N)积累率均保持稳定。同时反应器最后出水水质澄清,无需二沉池及污泥处理。     

全程自养脱氨氮悬浮填料床反应器性能的研究

以NH+4-N溶液为基质建立和启运了全程自养脱氨氮悬浮填料床反应器,反应器连续运行的实验结果表明在pH为8.0～8.5、溶解氧为0.7～1.0mg/L和温度为28℃的条件下.当氨氮表面负荷为2～2.5g/(m2@d)时,其表面去除速率为1.1～1.3/(m2@d),全程自养脱氮率基本稳定在55%左右;全程自养脱氮的最适pH范围为7.5～8,5,其中最佳pH为8.0左右;最适溶解氧范围为0.5～1.5mg/L,其中尤以0.8～1.0ms/L左右为最佳.     

流化床污泥干燥器床料的颗粒度对流化情况的影响

以上海白龙港污水处理厂流化床污泥干燥系统为研究对象,针对流化床污泥干燥器流化情况的好坏分析,在确定其它变量（流化风量、给料分配器转速、料层压差、运行负荷等）不变的情况下,对床料颗粒度的工艺参数进行研究实验,总结颗粒度的工艺参数对流化情况的运行变化规律,从而提高了流化床污泥干燥系统的稳定性、连续性和高效性。     

硫酸铵和尿素对废物焚烧过程中多种途径生成氯苯类的抑制作用

氯苯类(CBz)是废弃物焚烧等过程中产生二英的前驱物,也被认为是实现二英在线检测的良好指示物,同时五氯苯(PeCBz)和六氯苯(HxCBz)也是持久性有机污染物(POPs).但氯苯在废物焚烧过程中的排放和控制尚没有受到足够重视,为此开展了模拟焚烧过程中硫酸铵和尿素对3种氯苯合成途径的抑制作用研究,包括飞灰合成,1,2-二氯代苯(1,2-DiCBz)转化高氯代苯等过程.结果表明,硫酸铵和尿素对氯苯的3种合成途径均有抑制作用,如1%尿素与废物混合焚烧对四氯苯、五氯苯和六氯苯的抑制效率分别达到了66.8%、57.4%和50.4%.比较硫酸铵和尿素对3种过程的抑制作用,认为尿素对氯苯具有更稳定的抑制能力.