Environmental and economic assessment of a greenhouse waste heat exchange

As the economic costs of energy and the negative externalities associated with the combustion of fossil fuels threaten the economic viability of greenhouses in northern climates there is a renewed interest in the use of waste heat. This paper presents a technical and economic methodology to determine the viability of establishing waste heat greenhouses using the waste heat from industrial processes in northern climates. A case study is presented of an exchange between a tomato greenhouse and a flat glass manufacturing plant, which found the waste heat system is significantly more economic to operate than a purely natural gas system.     

动力与热力抬升对烟气抬升高度的影响分析

通过模式选择和计算,得出烟气抬升高度的增加与动能和热能的关系,表明当烟囱出口处风速分别为3 m/s、2 m/s和1 m/s时欲增加同样大小的烟气抬升高度,需要的动能比热能要高,结论认为烟气的热力提升比动力提升的贡献大。     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

Improvement of welding heat source models for TIG-MIG hybrid welding process

Tungsten inert gas-metal inert gas (TIG-MIG) hybrid welding process is an effective way to improve welding productivity and quality due to advantages of the two processes. Mathematical analysis is crucial to fundamentally understand this synergetic welding process. In this study, based on experimental visualization of arc behaviors, some assumptions are proposed to deduce adaptive plane and volumetric heat source models separately for each involved welding method first. The influence of torch angles on distribution of temperature and geometry of weld bead are calculated and compared with experimental results. It shows that this developed algorithm of heat source can be employed to accurately predict welding process whether the electrode gun is slanted backward or forward to the direction of welding. Then TIG-MIG hybrid welding process is simulated and analyzed without considering the attractive or repulsive force of two arcs. The characteristic of TIG-MIG welding process is discussed compared to single MIG. It lays the foundation for the further research on the interaction of the two arcs during TIG-MIG hybrid welding.     

秸秆压块与燃煤供热系统生命周期环境排放对比研究

为证明采用秸秆压块燃料替代煤炭进行供热的可持续性,对秸秆压块和燃煤供热系统的生命周期环境排放进行了对比分析.基于我国2012年投入产出表,构建了投入产出生命周期评价(IO-LCA)和过程生命周期评价(PLCA)相结合的混合生命周期评价(Hybrid-LCA)模型,核算了玉米秸秆压块和燃煤供热系统供应1 GJ热的生命周期CO2、SO2、NOx和PM2.5排放.结果显示,秸秆压块供热系统的生命周期CO2排放量为7 kg·GJ-1热,比燃煤供热排放减少121 kg.此外,秸秆压块供热系统比燃煤供热系统可以分别减少SO2排放98%、NOx排放76%和PM2.5排放58%.控制原料水分,通过减少原料收集和能源转化过程中的耗损,减少能源转化过程的电力消耗以及控制原料收集半径等可以有效改进秸秆压块供热系统环境表现.     

城市热岛效应下浅层土中混凝土的酸腐蚀试验研究

针对城市热岛效应引起城区浅层土地温场升高这一观测结果,采用室内快速模拟试验方法,对城区酸性土壤腐蚀混凝土材料的温度效应开展了试验研究.试验研究了在温度为5℃、20℃和40℃条件下,混凝土试样在酸浓度分别为0%、5%和10%的沙土介质中放置30 d、90 d后的抗压强度变化规律,并对混凝土试样在腐蚀过程中的腐蚀系数变化规...     

Effect of pipes in heat pump system on electric vehicle energy saving

ABSTRACT

Refrigerant pressure drop and temperature change in pipes are normally ignored in the thermodynamic analysis of traditional vehicle air conditioning system, this will result in serious errors. In this Paper, pressure drop and temperature difference are simulated in different pipes of electric vehicle (EV) heat pump system to analysis the effects of pipes in the actual EV heat pump system. The results indicate that the greater the mass flow, the faster pressure drop increases, the temperature difference decreases. Pressure drop of saturated liquid refrigerant is smaller than that of saturated gas refrigerant at the same saturation pressure and mass flow rate. The higher the refrigerant pressure (no phase change), the slower pressure drop decreases, the faster the temperature difference decreases. Pressure drop decreases with the increment of bending angle of the pipe. For EV heat pump system, suitable valves and less branches are helpful for energy saving of the system. Shortening the pipe between compressor and condenser can reduce temperature change obviously. Pressure drop per unit length in the pipe between evaporator and compressor is large especially in heating mode because of lower refrigerant density. It even reaches to over 100 times of that in the pipe between condenser and throttle valve in heating mode and has negative effects on the performance of the system. If the evaporator is closer to the compressor and the number of branches is less, then pressure drop will decrease a lot, which will be advantageous for energy saving of the heat pump system.     

Characteristics of stable biodiesel emulsion fuel with the aid of lipophilic surfactant,polyglycerol polyricinoleate (PGPR)

ABSTRACT

Biodiesel emulsion fuel is reported as one of the most feasible options capable of generating lower NOx emission than that from fossil fuels. However, oil and water in the emulsion fuel are easily separated and unstable. The aim of the present study is to consider the production and stability of biodiesel emulsion fuel by using tetraglycerin ester (CR-310), i.e., one of lipophilic surfactant, polyglycerol polyricinoleate (PGPR) and biodiesel, i.e., Waste cooking Oil Methyl Ester (WOME) produced based on waste cooking oil. The corresponding heat rate, water content, and viscosity are measured. Emphasis is placed on the effects of water content and surfactant on biodiesel emulsions. It is found that: (i) stable emulsion fuel is obtained by adding at least 2.0% of CR-310 and is maintained over 1 month, (ii) there is no effect of water content on stable emulsion fuel if CR-310 is used over 2.0%, and (iii) the viscosity of emulsion fuels is higher than that of the biodiesel fuel and is gradually increased with an increase in the water content.     

太阳热反射涂料的研制

根据涂料反射太阳热的原理,以丙烯酸树脂为基料,以金红石型钛白粉、云母粉及空心玻璃微珠为原料,制备了隔热性能和耐候性能均良好的太阳热反射隔热涂料,并研究了颜料、填料种类、粒径、涂层厚度对涂料隔热性能的影响。     

多热源分散程度的数学模拟及对置换通风影响

通过建立多污染热源置换通风的三维数学模型,根据数值解分析三热源位置变化对多污染源置换通风效果的影响,结果表明:热源的位置变化对多污染热源置换通风效果的影响是很大的,房间内热源应紧凑布置以利于提高通风效果和节能。