印铁涂装烘房有机废气的直接燃烧法处理实践

本文通过采用催化法和直燃法两种工艺处理印铁涂装生产的有机废气的工业实践,对设计和运行中的一些要点进行分析和探讨。     

Investigation the effect of adding graphene oxide into diesel/higher alcohols blends on a diesel engine performance

ABSTRACT

This article aims to study the influence of the addition of graphene oxide nanoparticles (GO) to diesel/higher alcohols blends on the combustion, emission, and exergy parameters of a CI engine under various engine loads. The higher alcohols mainly n-butanol, n-heptanol, and n-octanol are blended with diesel at a volume fraction of 50%. Then, the 25 and 50 mg/L concentrations of GO are dispersed into diesel/higher alcohols blends using an ultrasonicator. The GO structures are examined using TEM, TGA, XRD and FTIR. The findings show that there is a reduction in p_max. and HRR when adding higher alcohols with diesel fuel. Regarding engine emission, there is a significant improvement in emissions formation with adding higher alcohols. The addition of GO into diesel/higher alcohols blends improves the brake thermal efficiency by 15%. Moreover, the p_max. and HRR are both enhanced by 4%. The CO, UHC and smoke formation are reduced considerably by 40%, 50 and 20%, respectively, while NO_x level is increased by 30% with adding GO. Finally, adding high percentages of n-butanol, n-heptanol, and n-octanol with diesel fuel with the presence of GO has the potential to achieve ultra-low CO, UHC, and smoke formation meanwhile keeping high thermal efficiency level.     

Natural gas engine driven heat pump system – a case study of an office building

ABSTRACT

An eQUEST model was developed to conduct a simulation study of a natural gas engine-driven heat pump (GEHP) for an office building in Woodstock, Ontario, Canada. Prior to the installation of the GEHP, the heating and cooling demands of the office building were provided by rooftop units (RTUs), comprising of natural gas heater and electric air conditioner. Energy consumption for both GEHP and RTUs were monitored for operation in alternating months. These recorded energy consumptions along with weather data were used in the regression analysis. The developed eQUEST models were validated and calibrated with the regression analysis results with respect to the ASHRAE Guideline 14–2014. The eventual models were then applied to investigate the potential annual energy consumption, greenhouse gas (GHG) emission and energy cost savings achieved by using the GEHP in Woodstock, and other cities in Canada, particularly in Ontario.     

Radiation Effects on Blends of Poly(ε-Caprolactone) and Diatomites

Poly(-caprolactone) (PCL) was blended with diatomaceous earth (diatomite) and irradiated with -rays to introduce cross-linking between PCL molecules or both components. The unwashed diatomite containing a little of a volatile component showed high efficiency of introduction of cross-linking, whereas that with no volatile component showed low efficiency of introduction of cross-linking. Elongational viscosity, melt viscosity, and modulus of PCL/diatomite blend irradiated at various doses were significantly improved. Enzymatic degradation of the PCL/diatomite blend became faster than that of the PCL, though that of the blend irradiated became slower.     

热电联产发展中存在的环保问题及对策

结合我国热电联产项目发展现状,对其存在的主要问题进行了系统分析,从优化布局、清洁生产、节能降耗、推广热电冷联供、强化运行和管理等方面,提出了促进热电联产项目健康发展的对策建议.     

潮湿巷道风流温度与湿度变化规律分析

通过对矿井风流与围岩热湿交换理论的研究,提出理论上更可靠的风流温、湿度计算方法,编制了模拟解算矿井风流与围岩热湿交换的计算机程序,解算出潮湿巷道风流温度及湿度的变化规律,并分析通风时间、湿度系数等参数对风流温度及湿度变化规律的影响;沿风流流动方向,风流温度及湿度不断增加;巷道风流温度及湿度随着通风时间的增加而不断减小,通风时间越长减小的幅度越小;围岩壁面湿度系数对风流温度及湿度的影响较大,其他参数不变时,壁面湿度系数越大,风流温度越小,风流湿度越大。     

泵串联水灭火系统在森林防火方面的应用

现阶段为了适应国际及国内防火形势,出现了以水灭火为主要形式的灭火方式,并且在实际灭火中体现出巨大的优势.其中泵串联水灭火就是一种很好的形式.林海集团设计了一套远距离接力水泵串联供水灭火系统,尝试以手抬水泵(消防泵)接力供水的方式,从有水源的地方经过消防泵的增压,通过消防水带输送到火场,为水灭火工作提供条件,以实现水灭火.     

卷烟膨胀烟丝生产线冷端CO_2泵装置的优化改进

为解决干冰膨胀烟丝生产线冷端液体工艺泵因机械密封长期超压和气缚现象造成损坏发生CO2泄漏而导致紧急停机抢修的问题,对干冰膨胀线冷端工艺罐系统进行了优化改进。在工艺泵吸口前管路引一根气相平衡管至工艺罐顶部,当泵吸口前管路有CO2液体时,输送管路内气化的CO2气体通过气相平衡管线释放回工艺罐内,不会进入工艺泵体内。应用结果表明,工艺泵内的憋压和气缚现象消失了,机械密封受到保护。改造前机械密封平均一个季度更换一次,改造后机械密封使用5年未损毁,达到保护干冰膨胀线冷端工艺泵机械密封的目的。     

江苏省印染污泥现状分析

对江苏省四大纺织基地进行调研,掌握了17家典型的印染企业污水处理量、污泥脱水及处置方式.同时,取样分析了印染污泥中重金属镉(Cd)、铅(Pb)、总铬(Cr)、铜(Cu)、锌(Zn)和镍(Ni)及含水率、低位热值、灰分和氯离子含量的变化情况.研究表明:采用板框压滤脱水的印染污泥平均含水率可达66.42%,便于焚烧处置;将近1/2的污泥低位热值低于污泥助燃焚烧的限值,需对污泥处理工艺和脱水方式加以改进;污泥处理过程中含氯药剂的加入使得Cl-含量波动较大,焚烧时需加强对二英的监测;17家印染企业污泥中重金属平均含量均低于江苏省城市污泥重金属平均含量,但Zn的含量却远高于评价标准.本文可为江苏省印染污泥焚烧及污染防治工作提供技术支持.     

管道中烟道气流动传热及酸凝结规律

针对注烟道气稠油热采中管道输送烟道气酸凝结问题,以连续性方程、能量方程和动量方程为基础建立了烟道气沿管道流动与传热计算模型,计算了烟道气沿管道的压力分布、温度分布和酸凝结点距离,分析了不同入口参数和烟道气成分对管道中烟道气的压力、温度、酸凝结点的影响。结果表明:SO3或水蒸汽含量增加时,烟道气酸凝结点温度提高,凝结点距离减小;入口烟道气压力提高,烟道气压降变小,温降不变,酸凝结点距离减小;入口烟温升高,压降和温降都增大,酸凝结点距离增大;保温层厚度增加,温降减小,酸凝结点距离增大。计算和分析结果表明:减少烟道气中SO3或水蒸汽含量可以有效地增大酸凝结点距离,减轻管道腐蚀问题。