厌氧氨氧化工艺脱氮及其污泥形态的研究

为研究厌氧氨氧化工艺对高浓度含氮废水的脱氮性能,在以聚乙烯海绵作为填料的上流式厌氧固定床反应器中利用人工配置高浓度含氮废水进行了实验研究.实验中通过添加充足无机碳源,实现了厌氧氨氧化反应器在总氮浓度900～1 210 mg/L长期稳定的运行,脱氮效率在80％以上,最高氮负荷为5.9 kg/m3·d.结果表明:充足的无机碳源在一定程度上可有效地降低高浓度亚硝氮对厌氧氨氧化菌的抑制作用.通过对污泥性状的研究,明确寻找出污泥上浮的原因所在.通过Stover-Kincannon模型确定系统动力学参数KB和Umax分别为30.2 g/L·d和2L2g/L·d,这将有助于对该厌氧氨氧化系统各控制条件的有效调节和准确设定,也为日后应用于实际工程中提供重要的理论依据.     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

模拟氮沉降和CO2浓度增加对三江平原小叶章群落土壤总有机碳和氮素含量的影响

利用开顶气室(Open-Top Chamber,OTC),设置当前大气CO2浓度(370μmol.mol-1)、中等CO2浓度(550μmol.mol-1)和高CO2浓度(700μmol.mol-1)3个CO2浓度水平和不施氮(N1,0g N.m-2.a-1)、常氮(N2,5g N.m-2.a-1)、高氮(N3,10g N.m-2.a-1)3个氮素水平。研究了不同N沉降水平下,大气CO2浓度升高对以三江平原小叶章群落土壤有机碳和氮素含量的影响。结果表明:CO2浓度升高结合氮沉降连续运行两个生长季后,湿地土壤总有机碳含量没有显著变化,说明较短时间内大气CO2浓度升高和氮沉降不会使三江平原土壤有机碳含量产生变化。氮沉降引起各个土层的土壤全氮、铵态氮和硝态氮的含量增加,施氮水平越高土壤氮增加越多,但是全氮增加量不明显,铵态氮随施氮量的增加呈现极显著差异水平(P<0.01)。0～10cm,10～20cm土层土壤全氮、铵态氮的含量随着CO2浓度升高呈现出先增大后减小的趋势。土壤硝态氮含量在10～20cm土层含量变化与土壤全氮、铵态氮的变化趋势相同。说明大气CO2浓度一定程度的增加可以增加土壤的氮素含量,但是过量的大气CO2浓度反而会使得土壤氮素含量减少。     

用AGMP-1M阴离子交换树脂直接分离Zn的实验方法改进

针对原有用于铜、铁、锌同位素分析的提纯步骤方法,我们专门对锌的提纯进行了改进,即在1mol/LHCl的介质条件下,采用200~400目AGMP-1M树脂提纯锌,大大简化了锌的提纯方法。在改进的实验条件下,地质样品的回收率接近100%;标准溶液在离子交换分离前后同位素组成一致,表明分离前后无Zn同位素分馏;全流程Zn的空白小于0.7ng/mL。此法可作为用于高精度Zn同位素分析的前处理方法。     

有机氮替代比例对冬小麦/夏玉米轮作体系作物产量及N2O排放的影响

控制农业温室气体排放(如N_2O)是减缓全球气候变暖的一个重要措施.本研究通过动态监测小麦-玉米轮作体系N_2O排放通量,探究不施任何肥料(对照,CK)、单施氮磷钾化肥(NPK)、75%NPK+25%(有机氮M)(25%M)、50%NPK+50%M(50%M)、25%NPK+75%M(75%M)以及100%M,即不同有机氮替代比例对陕西关中塿土冬小麦/夏玉米轮作体系N_2O排放及作物产量的影响.结果表明,各处理N_2O排放通量在施肥、降雨或灌水后出现排放峰值.在小麦季各处理变化幅度为-1.33~144.2μg·(m~2·h)~(-1),其中NPK处理峰值最高.玉米季各处理变化幅度为88.2~1 800.1μg·(m~2·h)~(-1),50%M处理峰值最高.小麦/玉米一个轮作年不同处理N_2O排放总量为429.8~2 632.1 g·hm~(-2),且50%M25%MNPK75%M100%MCK.无论小麦、玉米还是一个轮作年总产量,施肥处理产量均显著高于对照.小麦季,施用有机肥的处理小麦产量均显著高于单施化肥处理,增幅达26.1%~50.0%.玉米季,50%M和75%M处理产量与NPK相似,而25%M和100%M处理玉米产量显著低于NPK处理.小麦/玉米轮作总产量变幅为9 166~17 496 kg·hm~(-2),其中50%M和75%M处理显著高于NPK处理,25%M和100%M处理与NPK处理无显著差异.综合考虑塿土小麦/玉米轮作体系有机氮替代化肥氮75%最好,可以保证作物产量、实现N_2O减排.