基于MGWR模型的中国城市PM2.5影响因素空间异质性

基于全国297个地级市2018年PM_2.5浓度数据、自然与社会经济数据,采用多尺度地理加权回归（MGWR）模型分析了各影响因素对PM_2.5浓度的作用尺度与影响效果的空间异质性.结果表明,MGWR模型适用于中国地级市PM_2.5浓度影响因素研究.在作用尺度上,人均GDP、技术支持水平作用尺度最大,其次是相对湿度、居民地比重、人口密度与风速,降水量、第二产业比重、植被覆盖状况、温度与能源消费强度作用尺度最为局限.在影响效果上,相对湿度、人口密度与居民地比重全部为正向作用;第二产业比重和能源消费强度主要为正向作用,分别占总样本的70.71%与64.98%;风速、温度既存在正向作用也存在负向作用,空间上呈两极分化,其中正向作用分别占总样本的49.83%与57.91%;降水量、植被覆盖状况主要为负向作用,分别占总样本的91.58%与69.70%;人均GDP、技术支持水平全部为负向作用.研究结果表明各因素对于中国城市PM_2.5浓度的影响均存在着不同程度的空间异质性.     

石墨烯量子点辅助合成Cu-MOFs及CO2吸附行为

选用一种成本低、可大规模合成的Cu基MOFs（Cu-MOFs）材料作为CO₂吸附剂,在原位合成过程中添加石墨烯量子点以调控其晶体结构.结果表明：适量石墨烯量子点的添加有利于提高Cu-MOFs的比表面积和孔体积,相比未改性MOFs材料,改性后的CO₂吸附性能有所提高,25℃,100kPa时提高了4.5%.随着温度升高,吸附容量提升越明显.改性后的MOFs对于N₂的吸附量则比未改性时更低,因此计算得到的CO₂/N₂吸附选择性也更高,增加了近一倍.综合等量吸附热的考察结果发现,尤其添加适量含N石墨烯量子点的Cu-MOFs吸附剂不仅具备了较高的吸附容量、吸附选择性,还展现了较理想的吸附热,因此兼具了较优CO₂吸附性能和较低脱附能耗的特点,为MOFs吸附剂的改性提供了一点参考价值.     

零价铁PRB技术在地下水原位修复中的研究进展

PRB(可渗透反应墙)是地下水治理中新型的原位修复技术,具有成本低、处理效果好、对环境干扰小等优点,已逐渐应用到实际. 原位修复技术中PRB根据结构的不同可分为单处理系统PRB和多单元处理系统PRB,单处理系统PRB适用于单一污染物、污染浓度较低、污染羽规模较小的场地,多单元系统用于污染场地较复杂、污染种类较多的场地. 零价铁PRB去除地下水中无机污染物及有机组分的反应机理主要是氧化还原反应和还原性脱卤反应. 实际场地PRB的运行中存在的主要问题是零价铁钝化及PRB堵塞,现阶段的解决方法主要包括超声、电化学等,但为了提高PRB技术的实用性,铁材料的解钝化技术、实际场地PRB的设计与安装、PRB体系的长期运行及服务期满后的处置均需进一步的研究探索.      

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets

A modified method of severe plastic deformation (SPD) entitled constrained groove pressing-cross route (CGP-CR) was introduced for imposing a high magnitude of equivalent strain of about 2.32 per pass on the sheet form samples. The major benefit of this improved route compared to previous common route was the more homogeneity of strain in the rolling (RD) and transverse (TD) directions of sheets. In this study, low carbon steel samples were used for examination of evolutions in microstructure and mechanical properties during SPD via CGP-CR process. Mechanical properties improvement were measured by tensile and macro hardness tests. The results indicate that CGP-CR process can effectively improve tensile strength; and also, yield stress and hardness of as-received low carbon steel samples were improved up to about 100% after two deformation passes. Also, high magnitude of inhomogeneity can be observed in hardness distribution through first pass of the process which diminishes in the subsequent passes. Microstructural evolutions during process were monitored by optical microscopy observations and X-ray diffraction analysis. The results demonstrate that initial ferritic microstructure with grain size of about 30 μm was refined to a 225 nm cell structure after two passes of CGP-CR process.     

Policy integration for adaptive water governance: Learning from Scotland's experience

This paper contributes to on-going attempts at bringing together two influential ideas in water governance: Integrated Water Resource Management (IWRM) and adaptive governance. In particular, a tension remains between the call in IWRM for the use of formal institutions, such as river basin organisations, to secure public policy integration, and the assumptions in adaptive governance in favour of informal collaboration between essentially independent policy actors. To clarify this relationship, this article draws on theoretical research on public policy integration, and uses these insights in an empirical setting to identify mechanisms that can facilitate effective policy integration for adaptive water governance. The research is based on recent attempts in Scotland to implement IWRM ideas to improve flood management. Several governance mechanisms were adopted to facilitate the integration of flood, water and rural land use policies. Six Scottish policy regimes are analysed using documentary sources and interviews. Results challenge the idea that collaboration should primarily be built on either river basin organisations or informal mechanisms. We identify a mix of informal and statutory-based mechanisms which may secure political and technocratic commitment to policy integration.     

2006~2019年珠三角地区臭氧污染趋势

研究基于2006~2019年粤港澳珠江三角洲区域空气监测网络数据,利用Mann-Kendall检验法和Sen斜率法等统计方法计算了珠三角不同区域臭氧年际变化情况,并分析了变化的原因.结果表明：①2006~2019年珠三角平均臭氧浓度上升趋势显著（P<0.05）,平均增长速率为0.80 μg·（m³·a）^-1.2016年之后,臭氧平均增长速率为2.08 μg·（m³·a）^-1,臭氧浓度增速加快.②珠三角臭氧浓度变化趋势有明显的空间差异和季节差异.中部地区臭氧年均浓度增加趋势显著,外围区域臭氧增加趋势不显著;臭氧增加趋势主要集中在夏季,其他季节变化趋势不显著.③珠三角臭氧变化趋势是由前体物和气象条件共同造成的,特别与NO_x的浓度变化密切相关.2006~2019年珠三角中部区域NO₂浓度明显下降,滴定效应减弱导致臭氧浓度增加;边缘地区NO₂浓度变化较小,臭氧浓度未发生明显的改变.④随着前体物浓度的变化,珠三角臭氧生成敏感区的特征正在发生改变,VOCs控制区面积不断减少,协同控制区和NO_x控制区面积逐渐增加,区域臭氧污染防治需要加强对前体物的协同控制.     

原位形成生物铁锰氧化物对砷(Ⅲ/V)的去除效果与机制

通过改变砷的初始浓度、砷价态、细菌接种比、铁锰浓度等因素来研究不同条件下Pseudomonas putida strain MnB1原位诱导形成生物铁锰氧化物（Biogenic Fe-Mn oxides,BFMO）对As（Ⅲ）和As（V）的去除效果与机制.结果表明：①当As（Ⅲ）和As（V）初始浓度为0.5~5 mg·L^-1时,原位形成的BFMO对As（Ⅲ）和As（V）有良好的去除效率,均在62%以上;②当细菌接种比为0.1%~0.5%时,As（Ⅲ）和As（V）的去除效率与细菌接种比成正比,当细菌接种比大于0.5%时,As（Ⅲ）和As（V）的去除效率基本维持在85%以上,未发生明显变化;③当MnCO₃浓度为0.2~0.8 g·L^-1或Fe（Ⅱ）浓度为2.5~25 mg·L^-1时,原位诱导产生的BFMO对As（Ⅲ）和As（V）的去除率随MnCO₃浓度或Fe（Ⅱ）浓度的增加而增大;当MnCO₃或Fe（Ⅱ）浓度再升高时,As（Ⅲ）和As（V）的去除效率基本保持不变.微观特征分析结果表明,原位形成的BFMO与As（Ⅲ）和As（V）反应后主要产物为As（V）,其去除主要以吸附为主,还存在共沉淀作用.总体而言,原位形成的BFMO适用于砷污染水环境的修复.     

南京北郊PM2.5中有机组分的吸光性质及来源

对南京北郊2018年9月~2019年9月PM_2.5中有机组分的吸光性质进行了研究,并利用PM_2.5化学组成及主成分分析法分析该地区吸光性有机碳（棕碳,brown carbon,BrC）的主要来源.结果表明,水溶性有机碳（water-soluble organic carbon,WSOC）和甲醇可提取有机碳（methanol extractable organic carbon,MEOC）在365 nm处光吸收系数（Abs_365,w和Abs_365,m）的平均值分别为（3.22±2.18）Mm^-1和（7.69±4.93）Mm^-1.Abs_365,w和Abs_365,m分别与WSOC（r=0.72,P<0.01）和MEOC（r=0.62,P=0.04）的质量浓度显著相关,均表现为冬高夏低,夜高昼低的时间变化特征.这可归结于冬季和夜间的气象特征（例如边界层高度降低和大气稳定度升高）、冬季一次源排放的增加以及夏季和白天更强的"光漂白作用".Abs_365,m/Abs_365,w的年均值（2.60±0.92）远高于MEOC/WSOC（质量浓度比值,1.37±0.30）,表明MEOC中非水溶性组分的吸光作用更强,在BrC的吸光作用中占主导地位.WSOC、MEOC、Abs_365,m和K⁺均未表现出强相关性（r<0.60）,因此生物质燃烧不是该地区BrC的主要一次来源.WSOC和MEOC质量吸收效率（MAE_365,w和MAE_365,m）及其比值（MAE_365,m/MAE_365,w）的季节变化和Abs₃₆₅相同.MEOC中非水溶性组分的MAE₃₆₅［（4.10±5.15）m²·g^-1］分别是MAE_365,w和MAE_365,m的6.0和2.9倍,支持BrC的吸光作用受非水溶性有机组分主导这一推断.和WSOC的埃氏吸收指数（Å_WSOC）相比,MEOC的埃氏吸收指数（Å_MEOC）随时间变化更显著,这可能与非水溶性吸光组分排放的季节变化有关.主成分分析结果显示,本研究PM_2.5中有机组分的吸光作用主要来源于二次形成过程和人为活动相关的一次排放,而不是生物质燃烧.     

西安市大气棕碳污染特性及发色团种类

为探究西安市大气棕碳(BrC)的光学特性及化学组成,利用大气颗粒物采样器和吸附剂同时采集了颗粒相和气相大气样品,并运用紫外-可见分光光度计和三维荧光光度计测定了样品中BrC的吸光和荧光特性,基于平行因子分析(PARAFAC)法解析三维荧光光谱得到BrC的种类和组成信息.结果表明,在波长为365 nm时,颗粒相和气相Br...