薄壁厚外螺纹的冷滚压

分析了薄壁厚外螺纹滚压成形的特点,介绍了薄壁厚外螺纹滚压加工方法.     

板料成形过程系统分析

此文从系统的角度就板料性能、板料毛坯的展开计算、模具设计与制造、摩擦与润滑、应力应变分析等诸多方面对板料成形过程作了一般分析.可知板料成形过程是一复杂的,需要考虑系统中各个因素之间的相互关系和影响才能得到合理的板料成形件.并从有限元法的角度,建立了板料成形过程模型.     

AZ31变形镁合金挤压成形工艺的研究

选择AZ31变形镁合金,设计了实心棒材、矩形和圆形截面薄壁空心型材试样,对坯料加热、模具预热、润滑剂、挤压比、挤压速度及挤压力等工艺问题与工艺参数,进行了系统的试验研究,总结了成形规律和确定工艺参数的方法,对生产应用将起到重要的参考作用。     

SiC颗粒尺寸对喷射共沉积7075 Al/SiCp挤压及轧制的组织和性能的影响

研究了喷射共沉积方法制备的7075 Al / SiCp复合材料挤压及轧制过程中SiC颗粒的分布.通过拉伸实验、微观组织的金相及拉伸断口SEM观察分析了SiCp颗粒尺寸对材料组织和性能的影响.实验表明,SiCp在挤压过程中沿厚度方向形成分层分布,SiCp的尺寸及粒度分布对于聚集有较大的影响;轧制过程对挤压时形成的SiCp分层分布有一定的减弱作用,但改善程度和SiCp的尺寸有关;SiCp颗粒尺寸对复合材料的力学性能及断裂机制有很大的影响.     

AZ31B镁合金挤压工艺研究

在油炉中熔炼AZ31B镁合金 ,用熔剂保护 ,石墨模铸造圆锭。铸锭经 40 0℃× 1 2h的均匀化处理后 ,进行热挤压 ,其挤压温度为 40 0℃ ,挤压速度为 1～ 2 .5m/min ,挤压比为 1 0～ 45。共挤出了 1 1种规格的棒材、管材、型材 (工字型、槽型、角形、方形、T形等 ) ,挤压过程中均发生了动态再结晶 ,其抗拉强度σb 在 2 75～ 2 85MPa之间 ,屈服强度σ0 .2　在 2 2 0～ 2 2 5MPa之间 ,延伸率δ在 1 5 %～ 1 7%之间。所制订的工艺合理 ,挤压出的棒材、管材、型材有较好的力学性能     

PHB/V in Extrusion Coating of Paper and Paperboard: Part I: Study of Functional Properties

Extrusion-coating experiments were carried out in the pilot line at Tampere Univesity of Technology (Institute of Paper Converting). Typical paper and paperboard substrates were coated with commercially produced 3-hydroxybutyrate/3-hydroxyvalerate. The resulting physical properties of extrusion-coated composite structures were studied. Adhesion between PHB/V and a fiber-based substrate was rather poor, regardless of typically used pretreatments (corona and flame). On the other hand, adhesion was sufficient (mode of failure was fiber tear as the materials were separated) when the substrate was primed with an acrylic-based primer. The surface energy and polarity of PHB/V were much higher than the respective ones of LDPE. Curling of PHB/V was reduced by the addition of wax or tall oil rosin into the base polymer.     

熏蒸废水一体化处理工艺分析研究——以四川某生物防治公司为例

四川某生物防治公司在利用磷化氢与二氧化碳混合气体熏蒸处理烟草和粮食杀菌生产过程中产生少量废水。废水主要含氢氧化铝等固体废物,具有产生量小、SS浓度大、颗粒物粒径极小、色度大、溢出气含腐蚀性等特点,对客户感官产生不适。结合该公司实例介绍了以"沉淀+一体化负压两级过滤"为主体的处理工艺的熏蒸废水处理过程。经过处理,该公司生产废水中SS和色度去除率可达到99.3%与98.1%,出水可满足相关标准与相应感官要求。     

A review of the biodegradability and utility of poly(caprolactone)

Since the early 1970s, it has been known that exposure of poly(caprolactone) (PCL) to a variety of microorganisms results in biodegradation of this polymer. Besides the ability of PCL to be utilized as a carbon source for microorganisms, it has been demonstrated that, during degradation, carbon dioxide is generated. Soil burial and compost experiments have shown that chain scission of the PCL backbone occurs, mechanical properties of articles prepared from PCL are reduced rapidly, and significant weight loss occurs in a short time period. This inherent biodegradability of PCL, in combination with its ability to be converted by conventional extrusion equipment, allows for the preparation of biodegradable articles that have utility.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

煤泥对水溶液中Ca^2＋的吸附性能研究

在静态条件下,研究了Ca^2＋在煤泥表面的吸附动力学。考察了不同Ca^2＋初始浓度的吸附实验,并对实验结果进行了动力学方程的拟合,结果表明,煤泥对Ca^2＋的吸附过程较好地符合准二级动力学方程。研究了初始Ca^2＋浓度、溶液pH值、振荡速度和煤泥质量对Ca^2＋吸附量的影响,实验结果表明：（1）煤泥对Ca^2＋吸附量随着Ca^2＋溶液浓度的增加而增大Ca^2＋浓度大于3．828mmol／L时,吸附量基本保持不变;（2）溶液pH〈9时煤泥颗粒对Ca^2＋的吸附主要是静电吸附,pH〉9时Ca^2＋在煤泥表面主要是沉淀吸附和一羟基吸附;（3）Ca^2＋在煤泥表面吸附的最佳振荡强度为150r／min。     

天然和巯基改性沸石吸附水溶液中重金属Hg^2＋的特征研究

为了提高沸石对汞的吸附性,利用半胱胺盐酸盐对天然斜发沸石进行改性,制得巯基改性沸石。研究了吸附剂用量、pH值、温度、Hg^2＋浓度和吸附时间对沸石和巯基改性沸石吸附Hg^2＋的影响,并进一步研究了吸附机理。结果表明,巯基改性沸石吸附Hg^2＋受pH值、温度的影响较小,吸附机制主要是沸石表面的硫与Hg^2＋的化学反应。而天然沸石对Hg^2＋的吸附主要是离子交换作用,受温度、pH值等的影响较大,随温度的升高吸附量下降。整个吸附过程以较快的速度进行。天然沸石在吸附时间为1h、巯基改性沸石在0．5h时基本达到吸附平衡。吸附条件试验和Langmuir等温吸附模型都表明,巯基改性沸石对Hg^2＋的吸附能力得到了很大的提高,吸附容量由8．06mg／g提高到19．88mg／g,提高了146．65％。