液/固相单一离子吸附体系的动力学预测模型

对四种液/固相单一离子吸附体系的动力学研究结果表明:吸附速率不仅随时间变化,也与起始离子浓度(C0)和吸附剂浓度(W0)有关;Lagergren准二级方程在给定的起始离子浓度及吸附剂浓度下具有很高的模拟精确度,但其参数随起始离子浓度和吸附剂浓度的变化而变化,且无法确定其间的函数关系;结合四组分离子吸附模型,提出了新的动力学方程,实验结果表明,新方程具有较高的模拟精确度,其参数与C0和W0具有相对稳定的函数关系,可作为液/同相单一离子吸附体系中给定C0,W0条件下吸附动力学过程的预测模型.     

高浓度钻井废泥浆处理工艺的试验研究

为实现钻井泥浆无害化处理,提出了"酸化破胶-固液分离-催化氧化-微生物降解"的处理方法,并采用钻井现场废泥浆进行了系列试验研究。结果表明:泥浆密度调节为1.15 kg/dm3,酸化pH≤3,固液分离效果最佳;过滤分离后固相浸毒液达到国家排放标准;液相经Fenton氧化、微生物降解后,COD将降低到110 mg/L以下。该方法运行成本低,处理彻底无隐患,为进一步工业化试验奠定了基础。     

电子垃圾拆解废渣-土壤-蔬菜中多氯联苯污染特征与健康风险评估

为研究某电子垃圾拆解区废渣-土壤-蔬菜中多氯联苯(PCBs)污染特征及对人体的潜在健康风险.对电子垃圾废渣样品采样3个、废渣旁的农田土壤和蔬菜分别采样10个和18个(油麦菜6个、四季豆6个和圆白菜6个).废渣、土壤和蔬菜中PCBs含量测定采用高分辨气相色谱-质谱法.结果表明,总PCBs水平:废渣(11 938ng·g-...     

Use of thermal analysis techniques (TG-DSC) for the characterization of diverse organic municipal waste streams to predict biological stability prior to land application

The use of organic municipal wastes as soil amendments is an increasing practice that can divert significant amounts of waste from landfill, and provides a potential source of nutrients and organic matter to ameliorate degraded soils. Due to the high heterogeneity of organic municipal waste streams, it is difficult to rapidly and cost-effectively establish their suitability as soil amendments using a single method. Thermal analysis has been proposed as an evolving technique to assess the stability and composition of the organic matter present in these wastes. In this study, three different organic municipal waste streams (i.e., a municipal waste compost (MC), a composted sewage sludge (CS) and a thermally dried sewage sludge (TS)) were characterized using conventional and thermal methods. The conventional methods used to test organic matter stability included laboratory incubation with measurement of respired C, and spectroscopic methods to characterize chemical composition. Carbon mineralization was measured during a 90-day incubation, and samples before and after incubation were analyzed by chemical (elemental analysis) and spectroscopic (infrared and nuclear magnetic resonance) methods. Results were compared with those obtained by thermogravimetry (TG) and differential scanning calorimetry (DSC) techniques. Total amounts of CO₂ respired indicated that the organic matter in the TS was the least stable, while that in the CS was the most stable. This was confirmed by changes detected with the spectroscopic methods in the composition of the organic wastes due to C mineralization. Differences were especially pronounced for TS, which showed a remarkable loss of aliphatic and proteinaceous compounds during the incubation process. TG, and especially DSC analysis, clearly reflected these differences between the three organic wastes before and after the incubation. Furthermore, the calculated energy density, which represents the energy available per unit of organic matter, showed a strong correlation with cumulative respiration. Results obtained support the hypothesis of a potential link between the thermal and biological stability of the studied organic materials, and consequently the ability of thermal analysis to characterize the maturity of municipal organic wastes and composts.     

Recovery of solid fuel from municipal solid waste by hydrothermal treatment using subcritical water

Hydrothermal treatments using subcritical water (HTSW) such as that at 234 °C and 3 MPa (LT condition) and 295 °C and 8 MPa (HT condition) were investigated to recover solid fuel from municipal solid waste (MSW). Printing paper, dog food (DF), wooden chopsticks, and mixed plastic film and sheets of polyethylene, polypropylene, and polystyrene were prepared as model MSW components, in which polyvinylchloride (PVC) powder and sodium chloride were used to simulate Cl sources.While more than 75% of carbon in paper, DF, and wood was recovered as char under both LT and HT conditions, plastics did not degrade under either LT or HT conditions. The heating value (HV) of obtained char was 13,886-27,544 kJ/kg and was comparable to that of brown coal and lignite. Higher formation of fixed carbon and greater oxygen dissociation during HTSW were thought to improve the HV of char.Cl atoms added as PVC powder and sodium chloride to raw material remained in char after HTSW. However, most Cl originating from PVC was found to converse into soluble Cl compounds during HTSW under the HT condition and could be removed by washing.From these results, the merit of HTSW as a method of recovering solid fuel from MSW is considered to produce char with minimal carbon loss without a drying process prior to HTSW. In addition, Cl originating from PVC decomposes into soluble Cl compound under the HT condition. The combination of HTSW under the HT condition and char washing might improve the quality of char as alternative fuel.     

Comparing the greenhouse gas emissions from three alternative waste combustion concepts

Three alternative condensing mode power and combined heat and power (CHP) waste-to-energy concepts were compared in terms of their impacts on the greenhouse gas (GHG) emissions from a heat and power generation system. The concepts included (i) grate, (ii) bubbling fluidised bed (BFB) and (iii) circulating fluidised bed (CFB) combustion of waste. The BFB and CFB take advantage of advanced combustion technology which enabled them to reach electric efficiency up to 35% and 41% in condensing mode, respectively, whereas 28% (based on the lower heating value) was applied for the grate fired unit. A simple energy system model was applied in calculating the GHG emissions in different scenarios where coal or natural gas was substituted in power generation and mix of fuel oil and natural gas in heat generation by waste combustion. Landfilling and waste transportation were not considered in the model. GHG emissions were reduced significantly in all of the considered scenarios where the waste combustion concepts substituted coal based power generation. With the exception of condensing mode grate incinerator the different waste combustion scenarios resulted approximately in 1 Mton of fossil CO₂-eq. emission reduction per 1 Mton of municipal solid waste (MSW) incinerated. When natural gas based power generation was substituted by electricity from the waste combustion significant GHG emission reductions were not achieved.     

甘氨酸母液脱色废活性炭的微波-Fenton试剂氧化法再生

采用微波-Fenton试剂氧化法对甘氨酸母液脱色过程中产生的废活性炭进行再生,考察了废活性炭再生率的影响因素,并用SEM对再生活性炭进行了表征.实验结果表明,在Fenton试剂中n(H2O2)∶n(Fe2+)为24∶1、H2O2的浓度为25 mmol/L、溶液pH为3、反应温度为55℃、反应时间为18 min、微波功率为600 W时,废活性炭的再生率可达到75.80％.     

响应面法优化阴阳极同时作用电化学法处理染料废水

在自制电化学反应器中,以甲基橙模拟染料废水为处理对象,采用Box-Behnken Design响应面法研究了影响阴阳极同时作用电化学法处理染料废水的因素及其交互作用。实验得出各因素对废水脱色率影响的大小顺序为：电流密度> Fe³⁺浓度>Cl^-浓度。各因素之间的交互作用对废水脱色率影响的大小顺序为：电流密度和Fe³⁺浓度>电流密度和Cl^-浓度>Fe³⁺浓度和Cl^-浓度。优化结果表明：Fe³⁺浓度为1.02 mmol/L、Cl^-浓度为10.96 mmol/L、电流密度为11.52 mA/cm²时,最佳脱色率为94.67%。阴阳极同时作用电化学法对甲基橙去除效果显著。     

MnOx/TiO2催化剂催化燃烧去除废气中的正己烷

采用溶胶-凝胶法制备了MnOx/TiO2催化剂,考察了n(Mn):n(Ti)、催化剂载体、气体流量对催化燃烧去除废气中正己烷效果的影响.实验结果表明:随着n(Mn):n(Ti)的增加,正己烷去除率先增加后减小,气体流量减小正己烷去除率增大;当n (Mn):n(Ti)为7.85％、气体流量为100 mL/min时,在240℃时正己烷的去除率为90％,MnOx/TiO2催化活性最大;MnOx/TiO2的催化活性优于MnOx/SiO2;SEM和XRD表征结果表明,所制备的MnOx/TiO2是一种活性物种MnOx高度分散的纳米结构催化剂.     

罐底油泥特性分析及其除油处理工艺

通过研究罐底油泥的理化性质,开发了适于处理罐底油泥的系列工艺:先采用调质技术提高罐底油泥流动性;再采用超声破乳降低油泥稳定性,改善油泥分离性能;最后采用卧式离心机对油泥进行离心分离处理.在复合型清洗剂加入量为800 mg/L、超声温度为60℃、超声功率为12 kW、超声时间为25 min、离心温度为60℃、絮凝剂加入量为600 mg/L、离心机转速为2200 r/min的条件下,系统稳定运行9d,离心机出口泥中含油率低于2.00％,水中悬浮固体质量浓度低于170 mg/L,达到了对罐底油泥进行除油的目的.