官地水电站竹子坝料场高边坡的稳定性分析及其影响因数研究

竹子坝料场是官地水电站混凝土浇筑骨料的重要来源之一。结合竹子坝料场的地形地质情况,以及料场开挖后形成的东、南、西三段人工边坡,运用刚体极限平衡的方法进行稳定性分析及其影响因数的研究。     

美国AERMOD模型与中国大气导则推荐模型点源比较

介绍了美国AERMOD模型和中国大气导则推荐模型一般浓度公式,通过大气稳定度和扩散参数的确定、复杂地形处理和对流条件下污染物扩散等原理方面的比较认为,AERMOD模型优于大气导则推荐模型.以美国环境保护局(USEPA)2个试验场Clifty Creek(平坦地形)和Lovett(复杂地形)的数据资料为比较数据,分别用AERMOD模型和大气导则推荐模型计算SO₂小时质量浓度,在Pasquill 6类稳定度下用相对偏差(FB)、预测值与观测值的比率(RHC_R)及图形法(Q-Q图)等进行模型比较,结果表明:在RHC_R和FB中,AERMOD模型除个别值外,其他均好于大气导则推荐模型;而大气导则推荐模型存在接近或大于模型可靠性界限0.67(0.66和0.74),说明其可靠性比AERMOD模型差;图形法比较中,强不稳定和不稳定下AERMOD模型明显好于大气导则推荐模型,而大气导则推荐模型预测值明显偏低,其他稳定度下结果相差不大.研究认为:在平坦地形和复杂地形条件下,AERMOD模型点源预测值均优于大气导则推荐模型,并从原理上进行了解释.      

Thermal decomposition mechanism of 65% lysine sulfate powder and its thermal stability based on thermal analysis

Lysine is widely used in the fields of food, medicine and feed, which generally appears in the form of lysine sulfate or lysine hydrochloride dust because of the high instability of the free L-lysine. The L-lysine Sulfate is in high risk of decomposition, spontaneous ignition and even the dust explosion, because the control temperature in its production process is high up to 90 °C. Thus, the thermal behaviors and its thermal stability of 65% lysine sulfate are experimentally explored in Air and Nitrogen using the simultaneous TG-DSC measurements. Results show: (1) the decomposition of 65% lysine sulfate can be divided into three stages both in the atmospheres of air and nitrogen, and most of the weight loss occurred in the first two stages, which are related with the decarboxylation and deamination process. (2) The effects of atmosphere on the decomposition of 65% lysine sulfate mainly occur at the third stage. In this stage, the weight loss in nitrogen is only 14.2%, which is much lower than that in air (34.3%), which is related to the oxidative degradation at high temperature. Besides, the active energy is slightly increased in nitrogen compared to that in air. (3) The initial temperatures of the decomposition of the 65% lysine sulfate are 145 °C and 155 °C, for the air and nitrogen atmosphere, respectively, which are much lower than that (260 °C) of the pure lysine.     

Composting of waste algae: A review

Although composting has been successfully used at pilot scale to manage waste algae removed from eutrophied water environments and the compost product applied as a fertiliser, clear guidelines are not available for full scale algae composting. The review reports on the application of composting to stabilize waste algae, which to date has mainly been macro-algae, and identifies the peculiarities of algae as a composting feedstock, these being: relatively low carbon to nitrogen (C/N) ratio, which can result in nitrogen loss as NH₃ and even N₂O; high moisture content and low porosity, which together make aeration challenging; potentially high salinity, which can have adverse consequence for composting; and potentially have high metals and toxin content, which can affect application of the product as a fertiliser. To overcome the challenges that these peculiarities impose co-compost materials can be employed.     

Developing Mechanism of Rubber-tea-chicken Agro-forestry Model in Tropical Area of China

As a typical tropical agro-forestry ecosystem in Wenchang,Hainan Province,China,rational mechanisms of the rubber-tea-chicken eco-agricultural model were studied with the Solow technological level index,stability indicator,harmonizing coefficient,grey correlation coefficient and production dominance.This study focused on rational hierarchical structure,the limiting factors and optimal strategies of the model development based on model structure,resource conditions and external market demands.Results showed that rational mechanism of the rubber-tea-chicken ecosystem model mainly included technological contributions,leverage function of dominance component(livestock husbandry),stability of the model structure and harmony of its components,the model dominant product’s market demand and government’s supporting policies.The contributions of fund,technology,information and talent resources played an important role in improving sustainability and productivity of the agro-forestry model.     

A hybrid method for quasi-three-dimensional slope stability analysis in a municipal solid waste landfill

Limited space for accommodating the ever increasing mounds of municipal solid waste (MSW) demands the capacity of MSW landfill be maximized by building landfills to greater heights with steeper slopes. This situation has raised concerns regarding the stability of high MSW landfills. A hybrid method for quasi-three-dimensional slope stability analysis based on the finite element stress analysis was applied in a case study at a MSW landfill in north-east Spain. Potential slides can be assumed to be located within the waste mass due to the lack of weak foundation soils and geosynthetic membranes at the landfill base. The only triggering factor of deep-seated slope failure is the higher leachate level and the relatively high and steep slope in the front. The valley-shaped geometry and layered construction procedure at the site make three-dimensional slope stability analyses necessary for this landfill. In the finite element stress analysis, variations of leachate level during construction and continuous settlement of the landfill were taken into account. The "equivalent" three-dimensional factor of safety (FoS) was computed from the individual result of the two-dimensional analysis for a series of evenly spaced cross sections within the potential sliding body. Results indicate that the hybrid method for quasi-three-dimensional slope stability analysis adopted in this paper is capable of locating roughly the spatial position of the potential sliding mass. This easy to manipulate method can serve as an engineering tool in the preliminary estimate of the FoS as well as the approximate position and extent of the potential sliding mass. The result that FoS obtained from three-dimensional analysis increases as much as 50% compared to that from two-dimensional analysis implies the significance of the three-dimensional effect for this study-case. Influences of shear parameters, time elapse after landfill closure, leachate level as well as unit weight of waste on FoS were also investigated in this paper. These sensitivity analyses serve as the guidelines of construction practices and operating procedures for the MSW landfill under study.     

Structure and thermal stability of toxic chromium(VI) species doped onto TiO2 powders through heat treatment

Chromium(VI)-containing sorbents in the form of sludge or solid residue from treatment processes are often landfilled or used as fill materials, therefore the long-term stability of metal binding is important. The reduction of Cr(VI)–Cr(III) through heat treatment may be a useful detoxification method. After heating at 500, 900, 1000, and 1100 °C for 4 h, the transformation of chemical states of chromium on 105 °C-dried, 7.9% Cr(VI)-doped TiO₂ powders was studied on the basis of surface area measurements, scanning electron microscopy (SEM) images, X-ray diffraction (XRD), and extended X-ray absorption fine structure (EXAFS) spectra. It was shown that Cr(VI) was reduced to Cr(III) in the Cr(VI)-doped samples after heating within 500–900 °C. The present results also suggested that the chromium octahedral was bridged to the titanium tetrahedral and was incorporated in TiO₂ minerals formed after 1000 °C treatment.     

Secondary arsenic minerals in the environment: A review

Information on arsenic (As) speciation in solid materials is critical for many environmental studies concerned with As stability and/or mobility in natural As-impacted soils and mining or industrial sites contaminated by As. The investigation of these systems has provided evidence for a number of secondary As minerals that have often played a significant role in As mobility in the solid phase–water system. This paper presents a list of environmentally important secondary As minerals in contaminated soil and waste systems, summarizes the information about their origin, occurrence, environmental stability and thermodynamics, and proposes several important avenues for further investigation.     

老垃圾填埋场渗滤液回灌工艺参数研究

根据理论分析,通过回灌能够实现对老垃圾填埋场所产生渗滤液的场内处理,改善渗滤液水质,同时能加速老填埋场的稳定化进程.以深圳市10座老垃圾填埋场为研究对象,提出渗滤液回灌工艺及其参数.回灌方式以水平渗沟为主,设置聚乙烯罐调节水量.渗滤液回灌加速了填埋气体产生速率,降低了有效应力,可能引起垃圾体边坡失稳.较大的渗滤液回灌量(1.6%)导致较低的垃圾边坡安全系数(1.96).确定满足加速垃圾稳定化和填埋场稳定性的最佳回灌量是填埋场渗滤液回灌大规模应用需要解决的重要问题.     

首钢孟家冲尾矿坝渗流稳定分析

针对孟家冲尾矿库坝面出现的渗水现象,对坝体的渗流以及稳定进行计算分析。计算结果表明,由于堆积坝的不断升高,导致坝体浸润线抬高,安全稳定系数降低,从而将造成坝体失稳,出现溃坝事故。为消除隐患,提出采用辐射井排渗的设计方案,并对该方案的可行性进行计算分析。