105万吨焦炉烟气脱硫脱硝除尘治理技术及应用

针对某企业焦炉烟气,新建一套脱硫脱硝除尘装置,焦炉烟气经过处理后,烟气中颗粒物、二氧化硫、氮氧化物以排放浓度满足《炼焦化学工业污染物排放标准》(GB16171-2012)大气污染物排放限值的要求。即:SO2排放浓度小于50mg/Nm^3,NOx排放浓度小于500mg/Nm^3,同时要求处理后烟气中颗粒物排放浓度小于30mg/Nm^3,氨含量排放浓度小于8ppm。     

Tertiary treatment of municipal wastewater using isolated algal strains: treatment efficiency and value-added products recovery

ABSTRACT

Two microalgal strains (Chlorella sorokiniana, A&B,) grown optimally at pH 9 (A) and 7 (B) were isolated from a municipal wastewater treatment plant. These strains were used to check their efficacy for nutrients and organic carbon removal capacities from the tertiary wastewater. The strains were characterised using 18S rDNA sequencing method and both the strains closely related to Chlorella sorokiniana. Different inoculum doses (IDs) of both the strains were tried to check their efficacy on wastewater treatment. Due to the increase in the IDs, hydraulic retention time decreased from 6 d to 1?d. On an average, 12–100% of total kjeldahl nitrogen, 53–96% NO₃–N, and 59–92% PO₄–P, were removed. Despite the same growth environment, strain A with the highest ID (700?mg/L) showed the best performance in terms of overall organic carbon removal, nutrient removal, and value-added products recovery. Strain A showed an increase in carbohydrate and protein content by 42% and 13%, respectively. Both the strains showed luxury phosphorus uptake and found suitable for advanced wastewater treatment.     

Removal and recovery of toxic nanosized Cerium Oxide using eco-friendly Iron Oxide Nanoparticles

• Eco-friendly IONPs were synthesized through solvothermal method. • IONPs show very high removal efficiency for CeO₂ NPs i.e. 688 mg/g. • Removal was >90% in all synthetic and real water samples. • >80% recovery of CeO₂ NPs through sonication confirms reusability of IONPs. Increasing applications of metal oxide nanoparticles and their release in the natural environment is a serious concern due to their toxic nature. Therefore, it is essential to have eco-friendly solutions for the remediation of toxic metal oxides in an aqueous environment. In the present study, eco-friendly Iron Oxide Nanoparticles (IONPs) are synthesized using solvothermal technique and successfully characterized using scanning and transmission electron microscopy (SEM and TEM respectively) and powder X-Ray diffraction (PXRD). These IONPs were further utilized for the remediation of toxic metal oxide nanoparticle, i.e., CeO₂. Sorption experiments were also performed in complex aqueous solutions and real water samples to check its applicability in the natural environment. Reusability study was performed to show cost-effectiveness. Results show that these 200 nm-sized spherical IONPs, as revealed by SEM and TEM analysis, were magnetite (Fe₃O₄) and contained short-range crystallinity as confirmed from XRD spectra. Sorption experiments show that the composite follows the pseudo-second-order kinetic model. Further R²>0.99 for Langmuir sorption isotherm suggests chemisorption as probable removal mechanism with monolayer sorption of CeO₂ NPs on IONP. More than 80% recovery of adsorbed CeO₂ NPs through ultrasonication and magnetic separation of reaction precipitate confirms reusability of IONPs. Obtained removal % of CeO₂ in various synthetic and real water samples was>90% signifying that IONPs are candidate adsorbent for the removal and recovery of toxic metal oxide nanoparticles from contaminated environmental water samples.     

Crosslinking acrylamide with EDTA-intercalated layered double hydroxide for enhanced recovery of Cr(VI) and Congo red: Adsorptive and mechanistic study

• Functional groups of AM and EDTA in composite increased removal of Cr(VI) and CR. • Removal process reached equilibrium within 30 min and was minimally affected by pH. • Elimination of Cr(VI) was promoted by coexisting CR. • Adsorption process of CR was less influenced by the presence of Cr(VI). • Mechanisms were electrostatic attraction, surface complexation and anion exchange. We prepared ethylenediaminetetraacetic acid (EDTA)-intercalated MgAl-layered double hydroxide (LDH-EDTA), then grafted acrylamide (AM) to the LDH-EDTA by a cross-linking method to yield a LDH-EDTA-AM composite; we then evaluated its adsorptive ability for Congo red (CR) and hexavalent chromium (Cr(VI)) in single and binary adsorption systems. The adsorption process on LDH-EDTA-AM for CR and Cr(VI) achieved equilibrium quickly, and the removal efficiencies were minimally affected by initial pH. The maximum uptake quantities of CR and Cr(VI) on LDH-EDTA-AM were 632.9 and 48.47 mg/g, respectively. In mixed systems, chromate removal was stimulated by the presence of CR, while the adsorption efficiency of CR was almost not influenced by coexisting Cr(VI). The mechanisms involved electrostatic attraction, surface complexation, and anion exchange for the adsorption of both hazardous pollutants. In the Cr(VI) adsorption process, reduction also took place. The removal efficiencies in real contaminated water were all higher than those in the laboratory solutions.     

Ammonia and phosphorus removal from agricultural runoff using cash crop waste-derived biochars

• Orange tree residuals biochar had a better ability to adsorb ammonia. • Modified tea tree residuals biochar had a stronger ability to remove phosphorus. • Partially-modified biochar could remove ammonia and phosphorus at the same time. • The real runoff experiment showed an ammonia nitrogen removal rate of about 80%. • The removal rate of total phosphorus in real runoff experiment was about 95%. Adsorption of biochars (BC) produced from cash crop residuals is an economical and practical technology for removing nutrients from agricultural runoff. In this study, BC made of orange tree trunks and tea tree twigs from the Laoguanhe Basin were produced and modified by aluminum chloride (Al-modified) and ferric sulfate solutions (Fe-modified) under various pyrolysis temperatures (200°C–600°C) and residence times (2–5 h). All produced and modified BC were further analyzed for their abilities to adsorb ammonia and phosphorus with initial concentrations of 10–40 mg/L and 4–12 mg/L, respectively. Fe-modified Tea Tree BC 2h/400°C showed the highest phosphorus adsorption capacity of 0.56 mg/g. Al-modified Orange Tree BC 3h/500°C showed the best performance for ammonia removal with an adsorption capacity of 1.72 mg/g. FTIR characterization showed that P = O bonds were formed after the adsorption of phosphorus by modified BC, N-H bonds were formed after ammonia adsorption. XPS analysis revealed that the key process of ammonia adsorption was the ion exchange between K⁺ and NH₄⁺. Phosphorus adsorption was related to oxidation and interaction between PO₄^3– and Fe³⁺. According to XRD results, ammonia was found in the form of potassium amide, while phosphorus was found in the form of iron hydrogen phosphates. The sorption isotherms showed that the Freundlich equation fits better for phosphorus adsorption, while the Langmuir equation fits better for ammonia adsorption. The simulated runoff infiltration experiment showed that 97.3% of ammonia was removed by Al-modified Orange tree BC 3h/500°C, and 92.9% of phosphorus was removed by Fe-modified Tea tree BC 2h/400°C.     

Using soybean isoflavone to prevent hydrogen production reaction of aluminium dust and water in wet dust removal systems

Using a dry dust removal system used for aluminium dust collection presents a dust explosion risk, whereas a wet dust removal system presents a risk of hydrogen fire and explosion. Neither system can attain a sufficient level of safety for use at aluminium processing sites. In this paper, soybean isoflavone, a non-toxic and environmentally sustainable flavonoid, was investigated to inhibit hydrogen production from aluminium dust and water. Scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and Fourier transform infrared spectroscopy (FTIR) were used to characterize aluminium particles before and after the reaction. Soybean isoflavone was found to inhibit hydrogen production from aluminium dust and water. At a soybean isoflavone solution concentration of 2.1 g L⁻¹, a dense protective film resulting from chemical adsorption on the surfaces of the aluminium particles isolated the aluminium particles from water molecules. This film blocked the reaction pathway between the aluminium particles and water to suppress hydrogen generation. This fundamental study addresses the problems of hydrogen fires and explosions in wet dust removal systems for aluminium dust collection and provides a novel, safe and effective method for aluminium dust removal.     

转炉二次除尘系统问题诊断及运行优化

针对某企业150 t转炉二次除尘系统烟气捕集效果不佳、布袋除尘器压差大、运行能耗高等问题进行了系统诊断,利用排查系统管网、实测压力和流量、分析风机特性等手段,找出了问题原因并提出改进措施。通过实施改进措施,优化了150 t转炉二次除尘系统的运行方式,确保二次除尘效果并实现节能、经济运行。     

湿法烟气脱硫对工业粉尘的协同脱除

通过对燃煤锅炉、烧结机和催化裂化炉排放工业烟气的湿法脱硫装置进出口粉尘特性的测试分析,从粉尘的粒径分布、疏水性以及吸收塔的内部结构研究湿法脱硫对3种工业烟气粉尘的协同脱除效果。结果表明,湿法脱硫具有粉尘的协同脱除作用,燃煤锅炉可以通过高效的湿法脱硫协同达到超低排放;而烧结烟气的粉尘疏水性高于燃煤粉尘,脱除效率一般,需要采用更复杂的吸收塔结构;催化裂化的粉尘由于细颗粒物占比更大,颗粒物的脱除效果比燃煤粉尘效果略差。     

MAP法沉淀回收装置的运行条件优化研究

采用一种简易的MAP回收装置,研究了间歇运行条件下反应时间和曝气量对MAP法除磷效果的影响,确定出最佳反应时间为90 min,最佳曝气量为1.2 L/min,相应的除磷率可达98.26%,沉淀回收率为74.54%。当增加一个漏斗形隔板分离反应区和沉淀区并连续运行时,除磷率和沉淀回收率分别为92.11%和63.66%。当不投加镁盐和铵盐而仅调控实际污泥脱水滤液的pH值为9.8时,其连续运行的平均除磷率和MAP回收率分别可达95.16%和70%,运行性能比较稳定。     

高效聚磷菌的选育及其特性研究

从鱼塘底部污泥中分离驯化得到一株高效聚磷菌株P5,采用厌氧/好氧(A/O)方式培养,在厌氧阶段3 h的最大释磷量为17 mg/L;在好氧条件下培养16 h后,P5对总磷(PO43--P)浓度为10~30 mg/L的模拟废水的除磷率均可保持在90%,COD的去除率达到82.1%。染色实验表明,P5是革兰氏阴性球杆菌,菌体内含有异染颗粒。