Review of the progress in preparing nano Ti02： An important environmental engineering material

TiO2 nanomaterial is promising with its high potential and outstanding performance in photocatalytic environmental applications, such as CO2 conversion, water treatment, and air quality control. For many of these applications, the particle size, crystal structure and phase, porosity, and surface area influence the activity of TiO2 dramatically. TiO2 nanomaterials with special structures and morphologies, such as nanospheres, nanowires, nanotubes, nanorods, and nanoflowers are thus synthesized due to their desired characteristics. With an emphasis on the different morphologies of TiO2 and the influence factors in the synthesis, this review summarizes fourteen TiO2 preparation methods, such as the sol-gel method, solvothermal method, and reverse micelle method. The TiO2 formation mechanisms, the advantages and disadvantages of the preparation methods, and the photocatalytic environmental application examples are proposed as well.     

TiO2光催化降解垃圾焚烧炉飞灰中二噁英的实验研究

光催化降解有机污染物是目前环保研究的热点课题。本文以垃圾焚烧炉的飞灰为对象,研究TiO2作为催化剂在500w汞灯照射下,飞灰中二噁英的随光照时间的降解效率。实验结果表明:在一定的光照条件下,TiO2光催化氧化分解二噁英的效率与飞灰本身的特性有关,特别是与飞灰含碳量以及铁等金属含量有关。飞灰中铁、铜等金属元素可促进二噁英光解,而碳则抑制了二噁英的光解。     

Performance of photocatalytic lamps on reduction of culturable airborne microorganism concentration

Reduction of viable airborne Staphylococcus epidermidis and Aspergillus niger spore concentrations using two types of photocatalytic fluorescent lamps under controlled environmental conditions (25 vs. 35 °C and 55 vs. 75% relative humidity) were investigated. Visible white-light and UVA black light were in-house spray-coated with TiO₂ and then compared with a commercially coated visible white-light for microbial concentration reduction. The white-light photocatalytic lamps reduced the concentration of culturable S. epidermidis up to 92% independent of temperature or humidity change, while the black light photocatalytic lamps completely inactivated the culturable bacteria at 25 °C, 55% relative humidity. Humidity seemed to alleviate UVA damage since better bacteria survival was found. For A. niger spores, rising humidity or temperature could lower their concentration or drop their culturabilities so that a difference between the natural decay and photocatalytic disinfection could not be distinguished. Reductions of total bacteria and total fungi concentrations using these lamps were also examined under uncontrolled environmental conditions in an office and a waste-storage room. It was found that photocatalytic lamps could reduce total culturable bacteria concentration from 9 to 97% and total culturable fungi concentration from 3 to 95% within irradiation time of 30-480 min, respectively. Insignificant difference in concentration reduction among these photocatalytic lamps was pronounced.     

Photocatalytic degradation of five sulfonylurea herbicides in aqueous semiconductor suspensions under natural sunlight

In the present study, the photocatalytic degradation of five sulfonylurea herbicides (chlorsulfuron, flazasulfuron, nicosulfuron, sulfosulfuron and triasulfuron) has been investigated in aqueous suspensions of zinc oxide (ZnO), tungsten (VI) oxide (WO₃), tin (IV) oxide (SnO₂) and zinc sulfide (ZnS) at pilot plant scale under natural sunlight. Photocatalytic experiments, especially those involving ZnO photocatalysis, showed that the addition of semiconductors in tandem with the oxidant (Na₂S₂O₈) strongly enhances the degradation rate of the herbicides in comparisons carried out with photolytic tests. The degradation of the herbicides follows a first order kinetics according to the Langmuir-Hinshelwood model. In our conditions, the amount of time required for 50% of the initial pesticide concentration to dissipate (t_½) ranged from 8 to 27 min (t_30W = 0.3-1.2 min) for sulfosulfuron and chlorsulfuron, respectively in the ZnO/Na₂S₂O₈ system. None of the studied herbicides was found after 120 min of illumination (except chlorsulfuron, 0.2 μg L⁻¹).     

Photocatalytic bacterial inactivation by polyoxometalates

The photocatalytic inactivation (PCI) of Escherichia coli (Gram-negative) and Bacillus subtilis (Gram-positive) was performed using polyoxometalate (POM) as a homogeneous photocatalyst and compared with that of heterogeneous TiO₂ photocatalyst. Aqueous suspensions of the microorganisms (10⁷–10⁸ cfu ml⁻¹) and POM (or TiO₂) were irradiated with black light lamps. The POM-PCI was faster than (or comparable to) TiO₂-PCI under the experimental conditions employed in this study. The relative efficiency of POM-PCI was species-dependent. Among three POMs (H₃PW₁₂O₄₀, H₃PMo₁₂O₄₀, and H₄SiW₁₂O₄₀) tested in this study, the inactivation of E. coli was fastest with H₄SiW₁₂O₄₀ while that of B. subtilis was the most efficient with H₃PW₁₂O₄₀. Although the biocidal action of TiO₂ photocatalyst has been commonly ascribed to the role of photogenerated reactive oxygen species such as hydroxyl radicals and superoxides, the cell death mechanism with POM seems to be different from TiO₂-PCI. While TiO₂ caused the cell membrane disruption, POM did not induce the cell lysis. When methanol was added to the POM solution, not only the PCI of E. coli was enhanced (contrary to the case of TiO₂-PCI) but also the dark inactivation was observed. This was ascribed to the in situ production of formaldehyde from the oxidation of methanol. The interesting biocidal property of POM photocatalyst might be utilized as a potential disinfectant technology.     

Simultaneous photocatalytic treatment of Cr(VI), Ni(II) and SDBS in aqueous solutions: Evaluation of removal efficiency and energy consumption

Simultaneous photocatalytic reduction of poisonous Cr(VI) and Ni(II) ions, coupled with photocatalytic oxidation of sodium dodecyl benzene sulfonate (SDBS) were studied with a trace amount of commercial titania nanoparticles and by means of a direct-photo-irradiation reactor. The co-presence of metal ions and SDBS causes metal ions reduction as well as SDBS oxidation to enhance and energy efficiency to improve. XRD, XPS and FTIR analysis were used to characterize TiO₂ particles before and after usage with the aim of evaluating the mechanism of reactions. The effect of major operating parameters, pH and temperature, was investigated. Under conditions of [Cr(VI)]₀ = [Ni(II)]₀ = 5 mg/L, [SDBS]₀ = 10 mg/L, [TiO₂] = 40 mg/L, pH 6 and T = 35 °C; the removal efficiencies of 55.4%, 71.2% and 57.2% were obtained, respectively, for Cr(VI) and Ni(II) reduction, as well as for SDBS oxidation, after 110 min operation. The relevant kinetic model jointed with the Arrhenius equation was introduced. Pseudo-first-order reactions are relevant. Energy consumption (electrical and thermal) evaluations revealed that operations at higher temperatures provide significant cost reduction. Meantime, a criterion was proposed for a consistent assessment of this kind of processes.     

Acid-assisted hydrothermal synthesis of nanocrystalline TiO2 from titanate nanotubes: Influence of acids on the photodegradation of gaseous toluene

In order to efficiently remove volatile organic compounds (VOCs) from indoor air, onedimensional titanate nanotubes (TiNTs) were hydrothermally treated to prepare TiO₂ nanocrystals with different crystalline phases, shapes and sizes. The influences of various acids such as CH₃COOH, HNO₃, HCl, HF and H₂SO₄ used in the treatment were separately compared to optimize the performance of the TiO₂ nanocrystals. Comparedwith the strong and corrosive inorganic acids, CH₃COOH was not only safer andmore environmentally friendly, but also more efficient in promoting the photocatalytic activity of the obtained TiO₂. Itwasobserved that the anatase TiO₂ synthesized in 15 mol/L CH₃COOH solution exhibited the highest photodegradation rate of gaseous toluene (94%), exceeding that of P25 (44%) by a factor ofmore than two. The improved photocatalytic activity was attributed to the small crystallite size and surface modification by CH₃COOH. The influence of relative humidity (20%-80%) on the performance of TiO₂ nanocrystals was also studied. The anatase TiO₂ synthesized in 15 mol/L CH₃COOH solution was more tolerant tomoisture than the other TiO₂ nanocrystals and P25.     

Surface modification of polypropylene non-woven fibers with TiO2 nanoparticles via layer-by-layer self assembly method: Preparation and photocatalytic activity

Polypropylene (PP) meltblown fibers were coated with titanium dioxide (TiO₂) nanoparticles using layer-by-layer (LbL) deposition technique. The fibers were first modified with 3 layers of poly(4-styrenesulfonic acid) (PSS) and poly(diallyl-dimethylammonium chloride) (PDADMAC) to improve the anchoring of the TiO₂ nanoparticle clusters. PDADMAC, which is positively charged, was then used as counter polyelectrolyte in tandem with anionic TiO₂ nanoparticles to construct TiO₂/PDADMAC bilayer in the LbL fashion. The number of deposited TiO₂/PDADMAC layers was varied from 1 to 7 bilayer, and could be used to adjust TiO₂ loading. The LbL technique showed higher TiO₂ loading efficiency than the impregnation approach. The modified fibers were tested for their photocatalytic activity against a model dye, Methylene Blue (MB). Results showed that the TiO₂ modified fibers exhibited excellent photocatalytic activity efficiency similar to that of TiO₂ powder dispersed in solution. The deposition of TiO₂ 3 bilayer on the PP substrate was sufficient to produce nanocomposite fibers that could bleach the MB solution in less than 4 hr. TiO₂-LbL constructions also preserved TiO₂ adhesion on substrate surface after 1 cycle of photocatalytic test. Successive photocatalytic test showed decline in MB reduction rate with loss of TiO₂ particles from the substrate outer surface. However, even in the third cycle, the TiO₂ modified fibers are still moderately effective as it could remove more than 95% of MB after 8 hr of treatment.     

Photocatalytic removal of nitrogen oxides via titanium dioxide

We studied the removal of nitrogen oxides pollutants via TiO₂ Degussa P25 powder by photocatalysis. Parameters such as mass of catalyst, geometric irradiated surface, catalyst morphology, and thermal treatment were tested to explain the photocatalytic concentration decrease of nitrogen oxides. According to our working conditions, the conversion rates increased until an optimal value of the TiO₂ weight, 35% of NO concentration and around 20% of NOx, was decomposed by the photocatalysis. The NOx removal increased proportionally with the irradiated geometric surface. The structural transformation of anatase to rutile performed by thermal treatment involved the decrease of the photocatalytic activity.     

磺化酞菁钴光催化降解甲基橙染料的试验研究

针对难降解的偶氮染料废水,在以磺化酞菁钴CoPcS为催化剂的情况下,实验研究了催化剂浓度、光照强度、温度、甲基橙初始浓度对降解效果的影响。结果表明:当催化剂CoPcS浓度0.2 g/L,光照强度250 W,温度40℃,pH=1,甲基橙10 mg/L时,在30 min内,甲基橙的降解率高达98.06%。最佳试验条件:pH值为1,催化剂浓度0.2 g/L,甲基橙初始浓度15 mg/L,温度40℃。影响因素主次为:pH值〉甲基橙初始浓度〉温度〉催化剂浓度,该反应符合零级反应动力学方程。