A study on emission of phthalate esters from plastic materials using a passive flux sampler

Phthalate esters are used as plasticizer in many plastics, and several studies have shown their toxicity. Phthalate esters are gradually emitted over time, and so it is conceivable that they pose a significant health risk. This study aims to investigate the temperature dependence of the emissions of various phthalate esters and to estimate the health risks of these emissions at various temperatures. A passive-type sampler was developed to measure the flux of phthalate esters from the surface of plastic materials. With this sampler, we examined three widely used plastic materials: synthetic leather, wallpaper and vinyl flooring. The observed maximum emissions of diethyl phthalate, dibutyl phthalate, and diethylhexyl phthalate (DEHP) from these materials at 20°C were 0.89, 0.77, and 14 μg m⁻² h⁻¹, respectively. Emissions at 80°C were 2.8, 4.5×10², and 1.5×10³ μg m⁻² h⁻¹, respectively. The results showed this temperature dependence is determined primarily by the type of phthalate ester and less so by the type of material. The estimation from the results of temperature dependence indicated the concentration of DEHP in a vehicle left out in the sunshine during the day can exceed the recommended levels of Japan Ministry of Health, Labour and Welfare.     

高气泡表面积通量浮选柱气浮除藻的研究

湖泊、水库等水源的富营养化，使藻类去除成为饮用水生产的重要任务。本研究采用高气泡表面积通量浮选柱气浮除藻，考察了混凝剂、气泡表面积通量和浮选柱高度等因素的影响。试验表明，高气泡表面积通量浮选柱气浮可高效地去除绿藻、硅藻和蓝藻，叶绿素a和藻类去除率达95％以上，比传统浮选柱气浮和沉降作业有较大幅度提高。与普通气浮柱比较，高气泡表面积通量浮选柱增加了气泡与藻的碰撞几率，防止因大表观充气速率造成的紊流和扰动，使气泡／藻结合体有相对静态的浮升环境，避免了气泡／藻结合体在浮升过程中的脱落，实现对藻类的迅速捕集和转移。     

Identification and characterization of extracted microplastics from agricultural soil near industrial area: FTIR and X-ray diffraction method

Microplastics have been found in large quantities in agricultural soil and now become a major global issue. Different types of microplastic have adverse effects on agricultural soil. The most widely used method for the extraction of microplastics in agricultural soil is the density floatation method by using saturated NaCl solution. This method includes the pre-digestion of soil samples with H₂O₂ to remove all the organic matter present in the soil. Different types of microplastic particles were extracted and identified by using ATR-FTIR viz polypropylene, polybutylene tetrapthalate, polyethylene, polystyrene, and polyethylene tetrapthalate. The crystalline nature of extracted microplastic was checked by employing XRD analytical technique. Floatation with higher density saturated sodium chloride (NaCl) solution recovered approximately 80% MPs from soil. Floatation methods were found to be effective for extracting microplastics from soils.     

旋流气浮除油装置预处理含油污水

在河南油田开展旋流气浮除油装置的现场试验,考察进水流量和曝气量对旋流气浮除油装置除油效果的影响。试验结果表明:在进水流量为1.8 m³/h、曝气量为0.5 L/min时,除油率最高达到96.03%;在不添加任何药剂的条件下,装置处理效果稳定;连续运行6 d内,进水含油量为174.57~1 193.15 mg/L时,出水含油量可以保持在137.38 mg/L以下,除油率为58.58%~94.53%。     

气浮净水高压射流溶气的可行性分析

利用CFD方法和Fluent软件模拟和分析了射流器在高、低压下内部和出口总体气体体积分数的大小和稳定性特点。通过比较高、低压射流溶气的相同点和差异,可得出结论:射流器高压(6～10 MPa)射流溶气是可行的,射流器出口的总体气体体积分数要大于低压(0.3～0.6 MPa)射流溶气,射流器在高压射流溶气下扩散管中总体气体体积分数的稳定性与低压射流溶气较接近。     

气浮/UASB/水解酸化/接触氧化处理增塑剂废水工程实例

以宁波爱敬化工有限公司增塑剂生产废水处理工程为例,基于其水质特征,构建气浮/UASB/水解酸化/接触氧化处理工艺,介绍该废水处理工程的工艺参数和调试及运行效果。运行结果表明:气浮/UASB/水解酸化/接触氧化处理工艺对增塑剂废水处理效果显著,在日平均进水量180 t/d,ρ(COD)=7 000 mg/L的情况下,出水可稳定达GB 8978—1996《污水综合排放标准》一级排放标准。     

Optimization of the recovery of plastics for recycling by density media separation cyclones

Material recovery processes are presented as the optimum option for recycling plastic wastes as a means of recovering hydrocarbon resources. There exist a large variety of automated material recovery processes for recycling of such wastes but each with significant limitations. Of these, the separation based on differences in densities is advocated as the optimum process either for producing recycled products or preparing wastes for subsequent recovery processing.Density separation processes based on cyclone type density media separation (DMS) is presented as an important, potential method for increasing plastics recycling process capacities. It is demonstrated to have the capacity to separate a significantly larger range of particle sizes than those presently processed industrially. The mathematical relationship for the prediction of quality of typical LARCODEMS type density media separations by particle size and density as expressed by the Ecart Probable is presented.A proposed device configuration is presented for density media separation to optimize the recovery and purity of both density fractions produced. It is also suggested that to be economically viable, a large scale of operation is required for industrial plastics recycling operations recovering and producing a number of different plastics with a purity to be used as a substitute for virgin material.     

混凝沉淀—气浮—生化处理洗毛废水

采用混凝沉淀－气浮－生化处理洗毛废水。混凝沉淀－气浮在进水ＣＯＤ１４５００ｍｇ／Ｌ,处理水量２０００ｍ＾３／ｄ,ＣＯＤ去除率９０％;ＨＲＴ ３２ｈ生化处理时,出水ＣＯＤ为１８７ｍｇ／ｌ,可达到污水综合排放二级标准（洗毛行业）。     

Fenton试剂处理选矿废水的实验研究

研究了用Fenton试剂处理某选矿废水中残余的黄药,分别考查了氧化时间、反应初始pH值、Fe2+浓度及H2O2用量对黄药降解效果的影响,用正交试验确定了四个因素的最好条件。结果表明:初始pH值和H2O2用量是影响去除效果的主要因素;氧化时间为60min,反应初始pH=4,[Fe2+]=20mg/L,[H2O2]=20mg/L,黄药的浓度为125mg/L时,黄药的去除率达到99.5%。     

溶气气浮过程动力学模型的分形观

凝聚/絮凝过程中形成的絮体通常具有分形几何结构,导致絮体的密度、渗透性发生了变化,从而对于固液分离过程(沉淀、气浮和过滤)带来很大的影响。本文基于前人对于絮体分形的研究成果,建立了絮体与微气泡之间接触碰撞的动力学方程、絮体/微气泡聚集体在水中上升的分形速率方程。絮体与微气泡间的相对尺度和流态的不同会有不同的碰撞机制,相应的动力学方程式与絮体的分形维数也有不同的关系。