常温处理生活污水微氧高效颗粒污泥反应器内颗粒污泥性能研究

为了分析微氧高效颗粒污泥反应器(EGSB反应器)在环境温度下处理实际生活污水时高效稳定运行的可行性,对15~26℃常温处理实际生活污水微氧EGSB反应器内颗粒污泥活性、沉淀性能、粒径分配、形态等进行研究.结果表明,15~26℃常温处理实际生活污水微氧EGSB反应器稳定运行时颗粒污泥沉速在11~79m·h-1之间,低沉速污泥有少量上浮至三相分离器底部甚至三相分离器上部,但没有出现污泥的流失,污泥浓度达到28g·L-1（以MLSS计）,可获得93.4%、83.8%、74.7%和44.0%的高COD、NH+4-N、TN和TP去除率;污泥产甲烷活性并没有降低,甚至比单纯厌氧时还有所偏高;颗粒污泥的平均粒径增大,主要集中0.63~2.00mm之间,质量分数达到了89%,既能保证反应器内的高污泥浓度,又能保证污染物质向颗粒表面和颗粒内部的高效传质,提高污染物质的转化率.颗粒污泥不同层面上微生物菌群发生了很大变化,外层丝状菌占优势,内层杆菌、丝状菌、球菌混生.微生物菌群排列紧密,细胞间紧密结合,集群协同作用使代谢物质能够以最短距离高效传递,保证了微氧EGSB反应器在常温、低浓度下的高效稳定运行.     

制革废水的厌氧氨氧化ABR脱氮工艺研究

采用小试规模的厌氧折流板反应器(ABR)研究制革废水的厌氧氨氧化脱氮.结果表明,ABR可作为实现厌氧氨氧化的良好反应器,厌氧氨氧化ABR反应器能有效和稳定地处理制革废水.当进水NH+4-N为25.0~76.2 mg·L-1、COD为131~237 mg·L-1,NH+4-N容积负荷为0.05~0.15 kg·(m3·d)-1时,出水NH+4-N为0.20~7.12 mg·L-1、COD为35.1~69.2mg·L-1,去除率分别达到90.8%~99.6%和66.9%~74.7%.此外,厌氧氨氧化ABR反应器污泥在驯化和运行过程中形成了棕红色、棕黄色和红色的颗粒污泥.电镜扫描观察证实在厌氧氨氧化ABR反应器的4个隔室的颗粒污泥中均存在厌氧氨氧化菌.荧光原位杂交(FISH)检测结果显示厌氧氨氧化菌在驯化和运行过程中出现不同程度的增殖,厌氧氨氧化ABR反应器4个隔室的污泥中厌氧氨氧化菌所占比率分别由4%增加到9%、8%、12%和30%,呈现出前段隔室少、后段隔室多的分布规律.     

气浮-水解酸化-UBF—SBR工艺处理硫酸卷曲霉素生产废水的试验研究

抗生素工业废水具有成分复杂、污染物浓度高、色度大、生物毒性等特点,比较难于治理,硫酸卷曲霉素是常用的抗生素之一,除具备抗生素污水上述特点外,还存在pH值波动范围大,水质、水量不均,SO4^2-浓度高等问题,研究采用气浮-水解酸化-UBF—SBR工艺处理含有硫酸卷曲霉素的污水,在进水COD浓度6000mg／L-20000mg,／L、SS浓度3000mg／L-8000mg／L的条件下,通过优化气浮药剂用量、水解酸化池废水停留时间、UBF池的客积负荷、SBR池的污泥负荷等处理工艺,使出水水质能够达到COD〈150mg／L、BOD5〈50mg／L、NH3-N〈20mg／L。     

新型厌氧氨氧化反应器脱氮性能及过程动力学特性的研究

对新型厌氧氨氧化折流板反应器的启动和运行性能进行了研究,并对其过程动力学特性进行了分析.试验中采用了两种启动策略：一是固定水力停留时间（HRT）（24h）并逐步提高进水基质浓度,二是固定进水浓度并逐步缩短HRT.结果显示后者（低基质浓度高水力负荷）更利于厌氧氨氧化反应器的启动.当厌氧氨氧化反应成功启动后,消耗的氨氮亚硝...     

厌氧UASB－好氧工艺处理染料废水的研究

报道厌氧,好氧工艺处理染料废水的试验结果,厌氧段采用ＵＡＳＢ反应器,好氧段采用普通活性污泥法。试验结果表明,进水ＣＯＤ１１５０－１３００ｍｇ／Ｌ色度５００倍的染料废水,在厌氧段停留６－１０ｈ,可获得６０％以上的ＣＯＤ去除率,色度降到５０－１００倍,后续曝气６ｈ,总ＣＯＤ去除率可达８５％－９０％,色度降至２０倍左右,进出水的光谱分析揭示,染料废水的脱色主要发生在厌氧段,并且通过生物降解作用来实现。从     

磺胺甲唑对海水养殖废水处理过程中抗性细菌及抗性基因的富集作用

抗生素在海水养殖过程中大量使用,但仅有少部分被生物体利用,含有抗生素的废水进入水处理系统后,抗生素、抗性菌和抗性基因的响应过程尚不完全清楚.应用缺氧/好氧移动床生物膜反应器（A/O-MBBR）处理含磺胺甲唑（SMX）的海水养殖废水,探究在SMX选择压力下,反应器内抗生素和抗性基因丰度的变化规律,以及微生物群落和可培养的抗性细菌种群的响应.结果表明,在进水SMX浓度为500 μg·L^-1,水力停留时间为8 h,SMX加入初期会对NH₄⁺-N和NO₂^--N的去除率有轻微影响,随后逐步恢复;同时去除约32%的SMX,且78%以上SMX在缺氧区完成;抗性基因在缺氧区富集明显高于好氧区,在缺氧区磺胺类抗性基因（sul1）绝对丰度上升2.43 log,磺胺类抗性基因（sul2）上升1.71 log;而在好氧区,sul1 绝对丰度上升1.17 log,sul2 上升0.91 log.抗性平板培养结合高通量测序表明,假交替单胞菌属（Pseudoalteromonas）在反应器可培养抗性细菌中占最优势.高通量测序分析发现可培养的抗性细菌假单胞菌属（Pseudomonas）在反应器内占比最高.表明含SMX的海水养殖废水可促进水中抗性基因的富集,部分抗性细菌的数量显著增加.     

Hydrodynamic characteristics of a four-compartment periodic anaerobic ba ed reactor

Periodic anaerobic baffled reactor (PABR) is a novel reactor based on the design concept of anaerobic baffled reactor (ABR). Residence time distribution (RTD) studies on both clean and working reactors at the same hydraulic residence time (HRT) of 2 d were carried out to investigate the dead spaces and mixing patterns in PABRs at different organic loading rates (OLRs) in various switching manners and frequencies.The results showed that the fraction of dead space in PABR was similar to that in ABR,which was low in comparison with other reactor designs.Dead space may be divided into two categories,hydraulic and biological.In RTD studies without biomass,the hydraulic dead space in the PABR run in an"every second"switching manner with T=2 d was the lowest whereas that in the PABR run in a T=∞(ABR) switching manner was the highest.The same trend was obtained with the total dead space in RTD studies with biomass no matter what the OLR was.Biological dead space was the major contributor to dead space but affected decreasingly at higher OLR whichever switching manner the PABR run in.The flow patterns within the PABRs were intermediate between plug-flow and perfectly mixed under all the conditions tested.     

厌氧折流板反应器对有毒有机物冲击负荷的适应性

在厌氧折流板反应器中,以氯酚配水进行毒物冲击负荷试验,进水ＣＯＤ为１１００～１２００ｍ ｇ／Ｌ,ＨＲＴ为１ｄ 时,连续２ｄ 投加五氯酚钠１６．８３～１７．７２ｍ ｇ／Ｌ．结果表明,厌氧污泥依次经历活性抑制阶段及活性恢复阶段．毒物冲击对反应器前段影响较大,对后段危害甚小．产酸菌比产甲烷菌先恢复,污泥活性恢复期为１８～２６ｄ,污泥驯化越好,其活性恢复越快．出水挥发酸和碱度变化也可表征系统恢复的进程     

Degradation of micropolluants in flow-through VUV/UV/H2O2 reactors: Effects of H2O2 dosage and reactor internal diameter

The degradation of atrazine (ATZ), sulfamethoxazole (SMX) and metoprolol (MET) in flow-through VUV/UV/H₂O₂ reactors was investigated with a focus on the effects of H₂O₂ dosage and reactor internal diameter (ID). Results showed that the micropollutants were degraded efficiently in the flow-through VUV/UV/H₂O₂ reactors following the pseudo first-order kinetics (R² > 0.92). However, the steady-state assumption (SSA) kinetic model being vital in batch reactors was found invalid in flow-through reactors where fluid mixing was less sufficient. With the increase of H₂O₂ dosage, the ATZ removal efficiency remained almost constant while the SMX and MET removal was enhanced to different extents, which could be explained by the different reactivities of the pollutants towards HO^?. A larger reactor ID resulted in lower degradation rate constants for all the three pollutants on account of the lower average fluence rate, but the change in energy efficiency was much more complicated. In reality, the electrical energy per order (E_EO) of the investigated VUV/UV/H₂O₂ treatments ranged between 0.14–0.20, 0.07–0.14 and 0.09–0.26 kWh/m³/order for ATZ, SMX and MET, respectively, with the lowest E_EO for each pollutant obtained under varied H₂O₂ dosages and reactor IDs. This study has demonstrated the efficiency of VUV/UV/H₂O₂ process for micropollutant removal and the inadequacy of the SSA model in flow-through reactors, and elaborated the influential mechanisms of H₂O₂ dosage and reactor ID on the reactor performances.     

启动三级PN/A颗粒污泥反应器处理高浓度氨氮废水

为将部分亚硝化-厌氧氨氧化技术(PN/A)应用于高浓度氨氮废水的处理,本研究以经破碎后的全自养脱氮颗粒污泥为种污泥,通过协同控制进水氨氮负荷(NLR)、各格室溶解氧(DO)水平和游离氨(FA)浓度等参数,在106 d内成功启动了三级连续流反应器.结果表明,颗粒污泥在启动初期呈现明显的亚硝化功能.反应器采用高NLR和限制曝气的控制策略,能够有效控制亚硝酸氧化菌增殖,并避免DO对厌氧氨氧化菌的抑制作用,有利于颗粒密实度和脱氮活性的提升.当进水氨氮浓度升至350 mg·L-1时,通过调节进水p H和碱度投加量,可以消除前端格室内高FA浓度对功能菌活性的不利影响.反应器最终实现了7. 2 kg·(m~3·d)-1的总氮去除负荷,较传统活性污泥法高出50～100倍.模拟不同曝气强度的序批次实验也证明,各格室污泥的脱氮活性持续增强,且格室1中颗粒污泥的成熟度最高.期间,胞外聚合物含量与比总氮去除速率呈现良好的线性相关(R2 0. 97),这意味着颗粒密实度的改善对提升反应器性能具有积极意义.