上海市电子废弃物产生量预测与回收网络建立

以上海市为例,利用无容量限制的设施选址模型(UFCLP模型)建立了上海市电子废弃物(WEEE)回收网络,同时,为获得模型求解所需数据,根据1991～2012年的销售量对上海市2010～2017年彩电、冰箱、洗衣机、空调和电脑的废弃量进行了预测.结果表明,5种电子产品的总废弃量会从2010年的269.49×104台增至2017年的635.75×104台.最后,依据区域GDP、人口密度和区域面积等多因素对电子废弃物空间分布量进行了预测,并以此为基础选取了214个回收站候选点,使用SITATION软件对UFCLP模型进行求解,最终确定10个点作为拟建回收点,可实现未来上海市约76%的电子废弃物回收.该网络的建立对长三角地区和全国大中型城市电子废弃物回收都具有良好的示范作用.     

The effect of heating temperature of thin film transistor-liquid crystal display (TFT-LCD) optical waste glass as a partial substitute partial for clay in eco-brick

In order to fulfill the current WEEE directives, the traditional approach to manage thin film transistor-liquid crystal display (TFT-LCD) waste glass is inadequate. It is a serious opportunity to achieve resource conservation, reduction, stabilization and safety of management of TFT-LCD in the near future. To assist in achieving these goals, this study investigated the sintering characteristics and material properties of TFT-LCD waste glass, which can be pulverized and ground and subsequently blended with clay, at various substitution levels (0–40%) and finally fired from 800 °C to 1000 °C to make eco-brick. The brick thus produced was analyzed to determine variations in weight losses on ignition, 24-h absorption, bulk density, shrinkage, compressive strength and microstructure changes. The results for specific gravity, water adsorption, and compressive strength revealed that bricks made from mixtures containing TFT-LCD waste glass met the general requirements for bricks. The advantages of less water absorption, less weight loss on ignition, and a gain in compressive strength in the clay-TFT-LCD waste glass bricks should encourage the use of TFT-LCD waste glass as a brick additive.     

废旧电子材料回收利用现状及发展展望

随着科学技术的进步，各类电子产品已经成为人们生活中不可缺少的组成部分，而其发展和普及的背后，我们将面临越来越多淘汰的废旧电子产品对环境带来的压力。与此同时，各类资源的短缺也需要从这些富含众多金属元素的废旧电子材料中找出解决办法。从废旧电子材料回收的紧迫性和必要性出发，分别介绍了目前国内外回收技术的现状及发展方向，并介绍了模型在回收技术发展和实际应用中可以起到的辅助作用。     

Implementation of Waste Electrical and Electronic Equipment Directive in Finland: Evaluation of the collection network and challenges of the effective WEEE management

Further to the European Waste Electrical and Electronic Equipment (WEEE) Directive, setting up efficient collection schemes is necessary to ensure the recovery targets set. Following the subsidiary principle, the WEEE Directive defines only the general requirements for mandatory collection and recycling objectives. The modalities of the logistics and the organisation of the take-back schemes are left to the choice of Member States. In this paper, the implementation of the WEEE Directive and the development of the WEEE recovery infrastructure in Finland are described and the challenges to the effective management of the WEEE recovery system in Finland are expressed. It can be said that the implementation of the WEEE Directive has succeeded in Finland and, at the same time, the legislative basis has been enacted. In addition, a functional WEEE recovery infrastructure has been built and, the collection requirements of the WEEE Directive have been exceeded in a relatively short time. However, the paper outlines that some inefficient practices still exist, particularly in the registration and WEEE collection stages. It is concluded that raising awareness would lead to a more environmentally sound behaviour and would, ultimately, improve WEEE recovery efficiency.     

Recycling-oriented characterization of plastic frames and printed circuit boards from mobile phones by electronic and chemical imaging

This study characterizes the composition of plastic frames and printed circuit boards from end-of-life mobile phones. This knowledge may help define an optimal processing strategy for using these items as potential raw materials. Correct handling of such a waste is essential for its further “sustainable” recovery, especially to maximize the extraction of base, rare and precious metals, minimizing the environmental impact of the entire process chain. A combination of electronic and chemical imaging techniques was thus examined, applied and critically evaluated in order to optimize the processing, through the identification and the topological assessment of the materials of interest and their quantitative distribution. To reach this goal, end-of-life mobile phone derived wastes have been systematically characterized adopting both “traditional” (e.g. scanning electronic microscopy combined with microanalysis and Raman spectroscopy) and innovative (e.g. hyperspectral imaging in short wave infrared field) techniques, with reference to frames and printed circuit boards. Results showed as the combination of both the approaches (i.e. traditional and classical) could dramatically improve recycling strategies set up, as well as final products recovery.     

Impact of closed-loop network configurations on carbon footprints: A case study in copiers

Growing concerns about the environment make a supply chains’ eco-footprint increasingly important, presuming that footprints are a more effective (policy) instrument than those currently in use. The eco-footprint comprises all kinds of environmental impact, but often is narrowed down to one aspect; e.g. the carbon footprint, material footprint, the water footprint, and so on. Although returns give rise to an additional goods flow from customers back to producers, it usually improves the eco-footprint due to the substitution effect. The reverse channel supplies high quality (recovered) products, components and materials to the forward channel thereby reducing the need for virgin sourcing and production. We refer to this as closed-loop recovery, as opposed to recovery for cascade markets which lacks substitution. To maximize substitution, the recovered items must re-enter the original supply chain. The feasibility of closed-loop recovery depends partly on the geographical proximity of forward and reverse facilities. We develop a decision framework for optimizing closed loop network configurations, i.e. the combined disposition and location–transport decision. We apply the framework to a single case study concerning one type of footprint (namely the carbon footprint) of a copier (closed-loop) supply chain. The main implication is that a regional network, with combined forward and reverse facilities per continent, proves most efficient and most robust in view of uncertain exogenous variables, but only when a full set of closed-loop options is available (including closed-loop recycling). As an embedded case, main contribution value of it lies in the discovery of a new phenomenon with generic implications; namely that not only the closed-loop supply chains footprint strongly depends on the substitution effect, but that in turn the feasibility of closed-loop recovery options depends heavily on the network design. From delineations of the study we derive issues for further research.     

Optimization of the recovery of plastics for recycling by density media separation cyclones

Material recovery processes are presented as the optimum option for recycling plastic wastes as a means of recovering hydrocarbon resources. There exist a large variety of automated material recovery processes for recycling of such wastes but each with significant limitations. Of these, the separation based on differences in densities is advocated as the optimum process either for producing recycled products or preparing wastes for subsequent recovery processing.Density separation processes based on cyclone type density media separation (DMS) is presented as an important, potential method for increasing plastics recycling process capacities. It is demonstrated to have the capacity to separate a significantly larger range of particle sizes than those presently processed industrially. The mathematical relationship for the prediction of quality of typical LARCODEMS type density media separations by particle size and density as expressed by the Ecart Probable is presented.A proposed device configuration is presented for density media separation to optimize the recovery and purity of both density fractions produced. It is also suggested that to be economically viable, a large scale of operation is required for industrial plastics recycling operations recovering and producing a number of different plastics with a purity to be used as a substitute for virgin material.     

An evaluation of legislative measures on electrical and electronic waste in the People's Republic of China

With the increasing number of recycling mishaps in connection with waste electronic and electrical equipment (WEEE) in the People's Republic of China, it is imperative that the handling and recycling of WEEE be sufficiently regulated in China. Regulations covering three major issues, namely, take-back issues, controls on hazardous substances in WEEE and the assurance of good environmental management in WEEE plants, were promulgated between 2006 and 2008. The evaluation in this country report shows that few of these regulatory measures have performed satisfactorily in terms of enforcement, of public acceptance and of environmental concerns. In brief, the take-back requirements and the associated financial responsibilities are only vaguely defined; the control on hazardous substances and the so-called "environmental expiry date" requirements cannot be properly enforced, and the resources needed to ensure the satisfactory enforcement of the environmental abatement and pollution control requirements in WEEE plants are overwhelming. In addition, the use of a "multiple enforcement body" approach to the control of hazardous substances in WEEE is an indication that the Chinese government lacks the determination to properly enforce the relevant legal requirements.     

A model for estimation of potential generation of waste electrical and electronic equipment in Brazil

Sales of electrical and electronic equipment are increasing dramatically in developing countries. Usually, there are no reliable data about quantities of the waste generated. A new law for solid waste management was enacted in Brazil in 2010, and the infrastructure to treat this waste must be planned, considering the volumes of the different types of electrical and electronic equipment generated.This paper reviews the literature regarding estimation of waste electrical and electronic equipment (WEEE), focusing on developing countries, particularly in Latin America. It briefly describes the current WEEE system in Brazil and presents an updated estimate of generation of WEEE. Considering the limited available data in Brazil, a model for WEEE generation estimation is proposed in which different methods are used for mature and non-mature market products.The results showed that the most important variable is the equipment lifetime, which requires a thorough understanding of consumer behavior to estimate. Since Brazil is a rapidly expanding market, the “boom” in waste generation is still to come. In the near future, better data will provide more reliable estimation of waste generation and a clearer interpretation of the lifetime variable throughout the years.     

我国电子废弃物资源化研究

文章分析了我国电子废弃物在回收、管理和利用方面的特性,预测了未来电子废弃物的产生量。研究表明,电子废弃物是具有双重性质的宝贵资源,且未来几年我国将进入电子电器产品淘汰的高峰期,2006年,我国将产生远远超过5.8亿台(部)的电子废弃物,到2010年,电子废弃物产生量将翻一番,达到12.98亿台(部)。鉴于此,建议我国未来的研究中,应重点关注以下几个领域:首先是建立合理的法律监管体系;其次,是建立有效的回收处理体系;最后,应积极鼓励新技术新工艺,特别是清洁生产工艺的研究与开发。