Hazard property classification of waste according to the recent propositions of the EC using different methods

Hazard classification of waste is a necessity, but the hazard properties (named “H” and soon “HP”) are still not all defined in a practical and operational manner at EU level. Following discussion of subsequent draft proposals from the Commission there is still no final decision. Methods to implement the proposals have recently been proposed: tests methods for physical risks, test batteries for aquatic and terrestrial ecotoxicity, an analytical package for exhaustive determination of organic substances and mineral elements, surrogate methods for the speciation of mineral elements in mineral substances in waste, and calculation methods for human toxicity and ecotoxicity with M factors.In this paper the different proposed methods have been applied to a large assortment of solid and liquid wastes (>1 0 0).Data for 45 wastes – documented with extensive chemical analysis and flammability test – were assessed in terms of the different HP criteria and results were compared to LoW for lack of an independent classification. For most waste streams the classification matches with the designation provided in the LoW. This indicates that the criteria used by LoW are similar to the HP limit values.This data set showed HP 14 ‘Ecotoxic chronic’ is the most discriminating HP. All wastes classified as acute ecotoxic are also chronic ecotoxic and the assessment of acute ecotoxicity separately is therefore not needed. The high number of HP 14 classified wastes is due to the very low limit values when stringent M factors are applied to total concentrations (worst case method). With M factor set to 1 the classification method is not sufficiently discriminating between hazardous and non-hazardous materials. The second most frequent hazard is HP 7 ‘Carcinogenic’. The third most frequent hazard is HP 10 ‘Toxic for reproduction’ and the fourth most frequent hazard is HP 4 “Irritant – skin irritation and eye damage”. In a stepwise approach, it seems relevant to assess HP 14 first, then, if the waste is not classified as hazardous, to assess subsequently HP 7, HP 10 and HP 4, and then if still not classified as hazardous, to assess the remaining properties.The elements triggering the HP 14 classification in order of importance are Zn, Cu, Pb, Cr, Cd and Hg. Progress in the speciation of Zn and Cu is essential for HP 14. Organics were quantified by the proposed method (AFNOR XP X30-489) and need no speciation. Organics can contribute significantly to intrinsic toxicity in many waste materials, but they are only of minor importance for the assessment of HP 14 as the metal concentrations are the main HP 14 classifiers. Organic compounds are however responsible for other toxicological characteristics (hormone disturbance, genotoxicity, reprotoxicity…) and shall be taken into account when the waste is not HP 14 classified.     

Recycling-oriented characterization of plastic frames and printed circuit boards from mobile phones by electronic and chemical imaging

This study characterizes the composition of plastic frames and printed circuit boards from end-of-life mobile phones. This knowledge may help define an optimal processing strategy for using these items as potential raw materials. Correct handling of such a waste is essential for its further “sustainable” recovery, especially to maximize the extraction of base, rare and precious metals, minimizing the environmental impact of the entire process chain. A combination of electronic and chemical imaging techniques was thus examined, applied and critically evaluated in order to optimize the processing, through the identification and the topological assessment of the materials of interest and their quantitative distribution. To reach this goal, end-of-life mobile phone derived wastes have been systematically characterized adopting both “traditional” (e.g. scanning electronic microscopy combined with microanalysis and Raman spectroscopy) and innovative (e.g. hyperspectral imaging in short wave infrared field) techniques, with reference to frames and printed circuit boards. Results showed as the combination of both the approaches (i.e. traditional and classical) could dramatically improve recycling strategies set up, as well as final products recovery.     

An investigation on the fuel savings potential of hybrid hydraulic refuse collection vehicles

Refuse trucks play an important role in the waste collection process. Due to their typical driving cycle, these vehicles are characterized by large fuel consumption, which strongly affects the overall waste disposal costs. Hybrid hydraulic refuse vehicles offer an interesting alternative to conventional diesel trucks, because they are able to recuperate, store and reuse braking energy. However, the expected fuel savings can vary strongly depending on the driving cycle and the operational mode. Therefore, in order to assess the possible fuel savings, a typical driving cycle was measured in a conventional vehicle run by the waste authority of the City of Stuttgart, and a dynamical model of the considered vehicle was built up. Based on the measured driving cycle and the vehicle model including the hybrid powertrain components, simulations for both the conventional and the hybrid vehicle were performed. Fuel consumption results that indicate savings of about 20% are presented and analyzed in order to evaluate the benefit of hybrid hydraulic vehicles used for refuse collection.     

Structure and activity of thermophilic methanogenic microbial communities exposed to quaternary ammonium sanitizer

Food processing facilities often use antimicrobial quaternary ammonium compound (QAC) sanitizers to maintain cleanliness. These QACs can end up in wastewaters used as feedstock for anaerobic digestion. The aim of this study was to measure the effect of QAC contamination on biogas production and structure of microbial communities in thermophilic digester sludge. Methane production and biogas quality data were analyzed in batch anaerobic digesters containing QAC at 0, 15, 50, 100 and 150 mg/L. Increasing sanitizer concentration in the bioreactors negatively impacted methane production rate and biogas quality. Microbial community composition data was obtained through 16S rRNA gene sequencing from the QAC-contaminated sludges. Sequencing data showed no significant restructuring of the bacterial communities. However, significant restructuring was observed within the archaeal communities as QAC concentration increased. Further studies to confirm these effects on a larger scale and with a longer retention time are necessary.     

Contribution of precursor compounds to the release of per- and polyfluoroalkyl substances (PFASs) from waste water treatment plants (WWTPs)

Per-and polyfluoroalkyl substances(PFASs) are ubiquitous in sludge and water from waste water treatment plants, as a result of their incorporation in everyday products and industrial processes. In this study, we measured several classes of persistent PFASs,precursors, transformation intermediates, and newly identified PFASs in influent and effluent sewage water and sludge from three municipal waste water treatment plants in Sweden, sampled in 2015. For sludge, samples from 2012 and 2014 were analyzed as well.Levels of precursors in sludge exceeded those of perfluoroalkyl acids and sulfonic acids(PFCAs and PFSAs), in 2015 the sum of polyfluoroalkyl phosphoric acid esters(PAPs) were 15–20 ng/g dry weight, the sum of fluorotelomer sulfonic acids(FTSAs) was 0.8–1.3 ng/g,and the sum of perfluorooctane sulfonamides and ethanols ranged from non-detected to 3.2 ng/g. Persistent PFSAs and PFCAs were detected at 1.9–3.9 ng/g and 2.4–7.3 ng/g dry weight, respectively. The influence of precursor compounds was further demonstrated by an observed substantial increase for a majority of the persistent PFCAs and PFSAs in water after waste water treatment. Perfluorohexanoic acid(PFHxA), perfluorooctanoic acid(PFOA), perfluorohexane sulfonic acid(PFHxS), and perfluorooctane sulfonic acid(PFOS)had a net mass increase in all WWTPs, with mean values of 83%, 28%, 37% and 58%,respectively. The load of precursors and intermediates in influent water and sludge combined with net mass increase support the hypothesis that degradation of precursor compounds is a significant contributor to PFAS contamination in the environment.     

烟草废弃物快速堆肥过程中重金属Cd形态变化特征

以烟草废弃物为原料,活性土壤为载体建立堆体,研究重金属镉的形态变化,及堆肥过程中的动态变化规律。结果表明,烟草废弃物与活性土壤混合能快速腐熟。堆肥总质量下降,重金属镉含量相对增加。重金属镉的铁锰氧化态比例增加19%,有机结合态比例在堆肥升温阶段增加,腐熟后有所下降。残渣态比例大幅度上升,增加达到5倍,且在腐熟阶段增幅最大。说明堆肥处理有利于降低重金属镉的活性。     

华南某金矿下游河道砷镉分布特征

对华南某金矿下游河道砷、镉分布特征进行了初步研究,在金矿下游河道沿程布设7个沉积物采样点及两个河道断面,分析了沉积物及断面土壤的砷、镉、铬、铜、镍、铅、锌含量。采用Tessier连续提取法分析沉积物中砷、镉等重金属的形态。砷含量高达10 208⁷0 621 mg/kg,镉含量达2.870 621 mg/kg,镉含量达2.8¹0.2 mg/kg。沉积物中砷、铅元素含量沿水流方向总体呈现减少趋势,铬、铜元素含量沿水流方向呈现增加趋势,镉元素含量沿水流方向先增加后减少。上游断面沉积物砷、镉等重金属浓度由河流中泓线向河岸方向增加,砷含量由16 617 mg/kg增加至53 197 mg/kg;下游断面则反之,砷含量由16 860 mg/kg减少至384mg/kg。沉积物中砷、镉等重金属元素主要以铁锰氧化态、有机结合态和残渣态的形式存在。     

微波消解/ICP-AES法分析冶炼厂固废中重金属

分析固体废物中金属元素全量分析的微波消解条件,通过实验确定样品的粉碎粒度、消解功率、消解温度、消解时间等因素对样品消解效果的影响,以等离子发射光谱测定冶炼厂固体废物中24种痕量金属元素,通过测定的检出限、精密度、准确度,确立冶炼厂固体废物痕量金属全量分析检测方法准确高效。     

生活垃圾中废塑料分选回收技术概述

近年来,废塑料在城市生活垃圾中占有相当大的比例,其含量正呈逐年上涨的趋势,因此对塑料进行分选和资源化利用势在必行。塑料分选技术是摆在我们中间的一项难题,目前生活垃圾废塑料的分选技术五花八门．由于在全国各地废塑料在垃圾中的还水量等因素的影响,现实中能实现废塑料的分选还不成熟。因此,研究一套适合废塑料的分选技术迫在眉睫。     

废弃电池能否进入废弃电器电子产品处理目录（第二批）管理的筛选评估分析

2009年2月,国务院发布《废弃电器电子产品回收处理管理条例》,成为我国废弃电器电子产品回收处理的纲领性文件。在《废弃电器电子产品处理目录（第一批）》中,明确将电视机、电冰箱、洗衣机、房间空调器、微型计算机等5种产品纳入第一批目录。同时,为了为了能够及时、客观地与经济发展、技术进步以及电器电子产品行业的发展变化等相适应,《目录》管理委员会起草了《制订和调整废弃电器电子产品处理目录的若干规定》,明确随着经济发展变化及电子产品废弃形势调整电器电子产品处理目录的原则。废弃电池在近几年来在我国增长速度很大,将来的管理形势十分紧迫。本文在此分析我国几种废弃电池（铅酸电池、镍氢电池及锂电池）的产生量、再生处理处置情况及管理政策导向。并在目录一批筛选原则的基础上利用权重分析法,筛选评估废弃电池能否进入废弃电器电子产品处理目录（第二批）管理的可能,研究显示铅酸电池已具备进入管理目录的资质。