Accurate sampling of PCDD/F in high temperature flue-gas using cooled sampling probes

In a laboratory-scale combustion reactor, flue-gas samples were collected at two temperatures in the post-combustion zone, 700 °C and 400 °C, using two different water-cooled sampling probes. The probes were the cooled probe described in the European Standard method EN-1948:1, referred to as the original probe, and a modified probe that contained a salt/ice mixture to assist the cooling, referred to as the sub-zero probe. To determine the efficiency of the cooling probes, internal temperature measurements were recorded at 5 cm intervals inside the probes. Flue-gas samples were analyzed for polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs). Samples collected at 700 °C using the original cooling probe showed higher concentrations of PCDD/Fs compared to samples collected using the sub-zero probe. No significant differences were observed between samples collected at 400 °C. The results indicated that artifact formation of PCDD/Fs readily occurs during flue-gas sampling at high temperatures if the cooling within the probe is insufficient, as found for the original probe at 700 °C. It was also shown that this problem could be alleviated by using probes with an enhanced cooling capacity, such as the sub-zero probe.Although this may not affect samples collected for regulatory purposes in exit gases, it is of great importance for research conducted in the high-temperature region of the post-combustion zone.     

DNA damage in caged Gammarus fossarum amphipods: a tool for freshwater genotoxicity assessment

The aim of this study was to propose a tool for freshwater environmental genotoxicity assessment using Gammarus fossarum, a high ecologically relevant species. In a first part, gammarids were caged upstream and downstream wastewater treatment plant effluent output. The sensitivity of genotoxic responses of haemocytes, oocytes and spermatozoa was compared using the Comet assay. Spermatozoa appeared to be the most sensitive, suitable and relevant cell type for genotoxicity risk assessment. In a second part, a watershed-scale study was conducted over 2 years to evaluate the applicability of our caging procedure. The genotoxic impact of a contamination was followed, taking into account seasonal variability. DNA damage in spermatozoa exhibited low basal level and low variability in control upstream sites, providing a reliable discrimination of polluted sites. Finally, DNA damage in caged G. fossarum has been proved to be a sensitive and reproducible tool for freshwater genotoxicity assessment.     

The role of intergenerational influence in waste education programmes: the THAW project

Whilst the education of young people is often seen as a part of the solution to current environmental problems seeking urgent attention, it is often forgotten that their parents and other household members can also be educated/influenced via home-based educational activities. This paper explores the theory of intergenerational influence in relation to school based waste education. Waste Watch, a UK-based environmental charity (www.wastewatch.org.uk), has pioneered a model that uses practical activities and whole school involvement to promote school based action on waste. This methodology has been adopted nationally. This paper outlines and evaluates how effective school based waste education is in promoting action at a household level. The paper outlines Waste Watch's 'Taking Home Action on Waste (THAW)' project carried out for two and half years in Rotherham, a town in South Yorkshire, England. The project worked with 6705 primary age children in 39 schools (44% of primary schools in the project area) to enable them to take the "reduce, reuse and recycle message" home to their families and to engage these (i.e. families) in sustainable waste management practices. As well as substantial increases in students' knowledge and understanding of waste reduction, measurement of the impact of the project in areas around 12 carefully chosen sample schools showed evidence of increased participation in recycling and recycling tonnages as well as declining levels of residual waste. Following delivery of the project in these areas, an average increase of 8.6% was recorded in recycling set out rates which led to a 4.3% increase in paper recycling tonnages and an 8.7% increase in tonnages of cans, glass and textiles collected for recycling. Correspondingly, there was a 4.5% fall in tonnages of residual waste. Waste Watch's THAW project was the first serious attempt to measure the intergenerational influence of an education programme on behaviour at home (i.e. other than schools' own waste). It clearly shows that household recycling behaviour can be positively impacted by intergenerational influence via a practical school-based waste education model. However, although the model could potentially have a big impact if rolled out nationally, it will require seed funding and the long-term durability of the model has not yet been fully quantified.     

Recycling of organic materials and solder from waste printed circuit boards by vacuum pyrolysis-centrifugation coupling technology

Here, we focused on the recycling of waste printed circuit boards (WPCBs) using vacuum pyrolysis-centrifugation coupling technology (VPCT) aiming to obtain valuable feedstock and resolve environmental pollution. The two types of WPCBs were pyrolysed at 600°C for 30 min under vacuum condition. During the pyrolysis process, the solder of WPCBs was separated and recovered when the temperature range was 400-600°C, and the rotating drum was rotated at 1000 rpm for 10 min. The type-A of WPCBs pyrolysed to form an average of 67.91 wt.% residue, 27.84 wt.% oil, and 4.25 wt.% gas; and pyrolysis of the type-B of WPCBs led to an average mass balance of 72.22 wt.% residue, 21.57 wt.% oil, and 6.21 wt.% gas. The GC-MS and FT-IR analyses showed that the two pyrolysis oils consisted mainly of phenols and substituted phenols. The pyrolysis oil can be used for fuel or chemical feedstock for further processing. The recovered solder can be recycled directly and it can also be a good resource of lead and tin for refining. The pyrolysis residues contained various metals, glass fibers and other inorganic materials, which could be recovered after further treatment. The pyrolysis gases consisted mainly of CO, CO(2), CH(4), and H(2), which could be collected and recycled.     

Policy implementation of the Republic Act (RA) No. 9003 in the Philippines: A case study of Cebu city

Municipal Solid Waste Management (MSWM) is considered to be one of the most serious environmental issues in the Philippines. The annual waste generation was estimated at 10.6 million tonnes in 2012 and this is expected to double in 2025. The Republic Act (RA) No. 9003, widely known as the Ecological Solid Waste Management Act of 2000, provides the required policy framework, institutional mechanisms and mandate to the Local Government Units (LGUs) to achieve 25% waste reduction target through establishing an integrated solid waste management plan based on the 3Rs (reduce, reuse and recycling). Although the initial impact of the LGUs is still very limited in implementing the national mandate, this article highlights the successful experiences of Cebu, the second largest city in the Philippines, in reducing its MSW generation by more than 30% in the past three years. This study also explores the implementation process, innovative actions taken by the Cebu City Government in implementing the national mandate at local level and identifies the factors that influence the policy implementation. The findings suggest that the impacts of the national mandate can be achieved if the LGUs have the high degree of political commitment, planning and development of effective local strategies in a collaborative manner to meet with local conditions, partnership building with other stakeholders, capacity development, adequate financing and incentives, and in the close monitoring and evaluation of performance.     

Preparation and performance of arsenate (V) adsorbents derived from concrete wastes

Solid adsorbent materials, prepared from waste cement powder and concrete sludge were assessed for removal of arsenic in the form of arsenic (As(V)) from water. All the materials exhibited arsenic removal capacity when added to distilled water containing 10–700 mg/L arsenic. The arsenic removal isotherms were expressed by the Langmuir type equations, and the highest removal capacity was observed for the adsorbent prepared from concrete sludge with heat treatment at 105 °C, the maximum removal capacity being 175 mg-As(V)/g. Based on changes in arsenic and calcium ion concentrations, and solution pH, the removal mechanism for arsenic was considered to involve the precipitation of calcium arsenate, Ca₃(AsO₄)₂. The enhanced removal of arsenic for the adsorbent prepared from concrete sludge with heat treatment was thought to reflect ion exchange by ettringite. The prepared adsorbents, derived from waste cement and concrete using simple procedures, may offer a cost effective approach for arsenic removal and clean-up of contaminated waters, especially in developing countries.     

A comparative assessment of waste incinerators in the UK

The uptake in Europe of Energy from Waste (EfW) incinerator plants has increased rapidly in recent years. In the UK, 25 municipal waste incinerators with energy recovery are now in operation; however, their waste supply chains and business practices vary significantly. With over a hundred more plant developments being considered it is important to establish best business practices for ensuring efficient environmental and operational performance. By reviewing the 25 plants we identify four suitable case study plants to compare technologies (moving grate, fluidised bed and rotary kiln), plant economics and operations. Using data collected from annual reports and through interviews and site visits we provide recommendations for improving the supply chain for waste incinerators and highlight the current issues and challenges faced by the industry. We find that plants using moving grate have a high availability of 87–92%. However, compared to the fluidised bed and rotary kiln, quantities of bottom ash and emissions of hydrogen chloride and carbon monoxide are high. The uptake of integrated recycling practices, combined heat and power, and post incineration non-ferrous metal collections needs to be increased among EfW incinerators in the UK. We conclude that one of the major difficulties encountered by waste facilities is the appropriate selection of technology, capacity, site, waste suppliers and heat consumers. This study will be of particular value to EfW plant developers, government authorities and researchers working within the sector of waste management.     

A preliminary investigation into the physical and chemical properties of biomass ashes used as aggregate fillers for bituminous mixtures

Fly and bottom ashes are the main by-products arising from the combustion of solid biomass. Since the production of energy from this source is increasing, the processing and disposal of the resulting ashes has become an environmental and economic issue. Such ashes are of interest as a construction material because they are composed of very fine particles similar to fillers normally employed in bituminous and cementitious mixtures. This research investigates the potential use of ash from biomass as filler in bituminous mixtures. The morphological, physical and chemical characteristics of 21 different ashes and two traditional fillers (calcium carbonate and “recovered” plant filler) were evaluated and discussed. Leaching tests, performed in order to quantify the release of pollutants, revealed that five ashes do not comply with the Italian environmental re-use limits. Experimental results show a wide range of values for almost all the investigated properties and a low correlation with biomass type in terms of origin and chemical composition. Furthermore, sieving and milling processes were found to improve the properties of the raw material in terms of grading and sample porosity. The effectiveness of these treatments and the low content of organic matter and harmful fines suggest that most of the biomass ashes investigated may be regarded as potential replacements for natural filler in bituminous mixtures.     

Municipal solid waste management: Identification and analysis of engineering indexes representing demand and costs generated in virtuous Italian communities

The definition and utilisation of engineering indexes in the field of Municipal Solid Waste Management (MSWM) is an issue of interest for technicians and scientists, which is widely discussed in literature. Specifically, the availability of consolidated engineering indexes is useful when new waste collection services are designed, along with when their performance is evaluated after a warm-up period. However, most published works in the field of MSWM complete their study with an analysis of isolated case studies. Conversely, decision makers require tools for information collection and exchange in order to trace the trends of these engineering indexes in large experiments. In this paper, common engineering indexes are presented and their values analysed in virtuous Italian communities, with the aim of contributing to the creation of a useful database whose data could be used during experiments, by indicating examples of MSWM demand profiles and the costs required to manage them.     

石油工业废弃物处置及其生物治理趋势

鉴于我国石油工作者对石油工业废弃物的普遍关注，现在介绍生物治理的基本概念及ＳＰＥ石油工程师协会中有关含油污泥生物处置的途径及其突出优越性。生物液／固处理工艺（ＬＳＴ）是目前含油污泥处置现场最经济可行的处置方案。这种好氧的ＬＳＴ工艺过程，能够比较充分地代谢和降解石油污泥中的油和脂并大量除去多环芳烃类（ＰＡＨ）化合物及其它有机化合物，明显地降低了石油废弃物对人、畜的毒害程度。其工艺较简单，操作也简易，凡经此工艺处理后的废弃物不留残毒和后患，因此早已被世界上先进国家的炼油业视为处理含油污泥的有效选择了。石油工业废弃物的生物防治和生物降解工艺较大程度地领先于目前我国现场正在执行的各种处理含油废弃物的处理工艺。