GeoChip-based analysis of the microbial community functional structures in simultaneous desulfurization and denitrification process

The elemental sulfur （S^0） recover）, was evaluated in the presence of hi,ate in two development models of simultaneous desulfurization and denitrification （SDD） process. At the loading rates of 0.9 kg S/（m^3.day） for sulfide and 0.4 kg N/（m^3.day） for nitrate, SO conversion rate was 91.1% in denitrifying sulfide removal （DSR） model which was higher than in integrated simultaneous desulfurization and denitrification （ISDD） model （25.6%）. A comprehensive analysis of functional diversity, structure and metabolic potential of microbial communities was examined in two models by using functional gene array （GeoChip 2.0）. GeoChip data indicated that diversity indices, community structure, and abundance of functional genes were distinct between two models. Diversity indices （Simpson＇s diversity index （1/D） and Shannon-Weaver index （H′）） of all detected genes showed that with elevated infiuent loading rate, the functional diversity decreased in ISDD model but increased in DSR model. In contrast to ISDD model, the overall abundance of dsr genes was lower in DSR model, while some functional genes targeting from nitrate-reducing sulfide-oxidizingbacteria {NR-SOB）, such as Thiobacillus denitrficans, Sulfurimonas denitrificans, and Paracoccus pantotrophus were more abundant in DSR model which were highly associated with the change of SO conversion rate obtained in two models. The results obtained in this study provide additional insights into the microbial metabolic mechanisms involved in ISDD and DSR models, which in turn will improve the overall performance of SDD process.     

城市污水处理厂二级出水深度处理回用的设计与运行

将城市污水作为工业循环冷却补充水的水源已成为世界各国解决缺水问题的主要方案之一,但二级出水水质不符合循环冷却水对CODCr、硬度、氮、磷等指标要求,必须对其进行深度处理才能回用。本设计采用生物接触氧化+絮凝沉淀+机械搅拌澄清+连续动态过滤+消毒工艺,其出水补充至电厂循环冷却水系统。运行实践表明,该工艺处理效率高,动力消耗少,出水水质达到循环冷却水水质标准,且经过对工艺的改进完善,使操作更加简便,设备运行更加稳定。     

生物流化床去除水中腐殖酸的动力学模式

对腐殖酸的吸附机理作了论述。在Monod方程基础上,结合生物量、世代时间及停留时间之间的关系,推导出稳态条件下腐殖酸（HA）的降解动力学模式ss₀＝11＋a₁s₀＋a₂θ。利用非线性最小二乘法,对动力学模式中的待定参数a₁、a₂进行了优化估计,得出a₁＝0.0171,a₂＝0.079。以实验数据对该动力学模式加以验证,结果令人满意     

深床过滤颗粒截留机理研究

对深床过滤过程中颗粒物与滤料之间的相互作用进行了理论分析,讨论了两者间的相互作用及影响因素对微絮凝深床过滤进行了中试研究,考察了1～l0μm粒径颗粒在500cm滤床中的截留情况,并连续65h监测滤柱水头损失的变化;在滤速为24m/h情况下,计算了1～10μm粒径颗粒所受的水流剪切力;利用理论分析,分别讨论了表面电位为-25mV及-125mV、粒径为1～10μm的颗粒与滤料之间的物理化学作用力.理论计算值对实验结果进行了很好的解释,说明可以通过颗粒与滤料间的作用力分析来研究均质滤料深床过滤运行规律.     

河流污染物通量估算方法分析(Ⅱ)——时空平均离散通量误差判断

提出了一个简单的通量误差判断公式,对于采用以时空平均的一维对流量方式估算河流通量,提出了限制的条件,即排除不可靠的通量估值的方法,就河流离散通量对于通量估算的影响提供了误差判断分析方法.      

鄱阳湖泥沙淤积特征及发展趋势

在两年来的野外实地调查及大量前人资料系统综合研究的基础上。简要的介绍了鄱阳湖的地形地貌，重点对鄱阳湖的泥沙淤积特点分五河尾闾地区（赣江，抚河，信江，饶河及修水）及鄱阳湖淤积区（鄱阳湖入江水道口淤积区Ⅱ1，赣江三角洲淤积区Ⅱ2，青岚湖淤积区Ⅱ3，抚河入湖口淤积区Ⅱ4，修水入湖口淤积区Ⅱ5，信江入湖口淤积区Ⅱ6，饶河入湖口淤积区Ⅱ7，鄱阳湖中心湖盆淤积区Ⅱ8，东北湖湾淤积区Ⅱ9，环鄱阳湖周边淤积区Ⅱ10）分别进行详细的描述。对鄱阳湖湖泥沙的来源进行了分析。在此基础上对鄱阳湖未来泥沙淤积的发展趋势按不同的淤积区分别进行了详细预测，提出了从被动防洪转变为积极防洪，从“抵抗”洪水转变为顺应洪水的自然规律，从以防为主转变为以疏导为主的鄱阳湖区水患灾害防治的基本思路。     

循环流化床烟气脱硫系统控制技术

阐述了循环流化床烟气脱硫系统电气控制的内容、方法、仪表等技术。根据循环流化床烟气脱硫实验系统温度、压力、流量的测量,实现了该系统闭环开环自动、手动控制的功能,并且根据实验室的具体情况,采取特殊技术方式,完成实验自动化的控制。该控制技术对扩大到实际工程应用具有指导意义。     

地震动特征的统计分析

统计了国内外287次5级以上的实际地震记录,研究了地震动峰值不对称比、持时、地震荷载类型的统计特征和规律。结果表明：地震动峰值具有明显的不对称性,可以用峰值不对称比描述,统计结果具有规律性,其平均值总体上随震级加大而略有降低,从5级到8级地震其范围变化为1.4～1.2;地震动持时随震级增大而增大,近似于线性增长,震级从...     

流化床厌氧反应器流化及反应特性研究

对流化床厌氧反应器的流化及反应特性进行研究,结果显示:床层实际初始流化流速umf为0.138～0.154cm/min,与理论计算值0.143 cm/min一致;在一定范围内,流速增大有利于反应量的提高,当流速为0.414 cm/min时,单位时间内的反应量达到最大,其值为4.66 mg/(L·min);适当提高流速有利...     

Sulfide oxidation in fluidized bed bioreactor using nylon support material

A continuous fluidized bed bioreactor (FBBR) with nylon support particles was used to treat synthetic sulfide wastewater at different hydraulic retention time of 25, 50 and 75 min and upflow velocity of 14, 17 and 20 m/hr. The effects of upflow velocity, hydraulic retention time and reactor operation time on sulfide oxidation rate were studied using statistical model. Mixed culture obtained from the activated sludge, taken from tannery effluent treatment plant, was used as a source for microorganisms. The diameter and density of the nylon particles were 2-3 mm and 1140 kg/m³, respectively. Experiments were carried out in the reactor at a temperature of (30 ± 2)℃, at a fixed bed height of 16 cm after the formation of biofilm on the surface of support particles. Biofilm thickness reached (42 ± 3) μupm after 15 days from reactor start-up. The sulfide oxidation, sulfate and sulfur formation is examined at all hydraulic retention times and upflow velocities. The results indicated that almost 90%-92% sulfide oxidation was achieved at all hydraulic retention times. Statistical model could explain 94% of the variability and analysis of variance showed that upflow velocity and hydraulic retention time slightly affected the sulfide oxidation rate. The highest sulfide oxidation of 92% with 70% sulfur was obtained at hydraulic retention time of 75 min and upflow velocity of 14 m/hr.