Facilitating substance phase‐out through material information systems and improving environmental impacts in the recycling stage of a product

The amount of electrical and electronic products is increasing rapidly, and this inevitably leads to the generation of large quantities of waste from these goods. Some of the generated e‐waste ends up in regions with sub‐standard recycling systems and may be processed under poor conditions. During uncontrolled incineration, halogenated dioxins and furans can be generated from brominated and chlorinated compounds in the products. In order to reduce the health and environmental risks involved in the recycling stage of the life cycle of electronics, an effective design‐for‐environment process must be established during the product development phase. Knowledge of the chemical substances in the product is crucial to being able to make informed decisions. Through full knowledge of the material content of procured components, phase‐outs of unwanted substances, such as halogenated substances, can be performed in an effective manner. Therefore, information is the key to success in phasing‐out substances; facilitating compliance of legal provisions for manufacturers of electrical and electronic devices; and improving the environmental footprint of products as they reach the end of the life cycle. After an introduction to the challenges of electronics waste management, this paper describes supply chain information systems and how they are used to facilitate substance phase‐outs in the electronics industry. Sony Ericsson has been working with phase‐outs of unwanted substances since it was founded in 2001. Through the introduction of a material declaration system that keeps track of all substances in the components used in the company's products, Sony Ericsson has been able to replace unwanted substances to improve environmental impacts at the recycling stage of a product.     

基于冷阴极触发管振动试验夹具的设计

介绍了一种基于冷阴极触发管性能检测及振动试验所需的夹具,从夹具材料的选取、结构设计和刚度要求进行了设计,分析了该夹具在制造过程中存在的关键问题及解决方法,并在振动试验中加以验证。     

袋式除尘器在沥青混凝土搅拌设备上的应用

分析了沥青混凝土搅拌设备的构成以及生产沥青混凝土的工艺及烟尘特点;通过应用工程实例,指出袋式除尘器是沥青混凝土搅拌设备最理想的除尘系统之一。     

Petrophysical analysis to investigate the effects of carbon dioxide storage in a subsurface saline aquifer at Ketzin, Germany (CO2SINK)

To test the injection behaviour of CO₂ into brine-saturated rock and to evaluate the dependence of geophysical properties on CO₂ injection, flow and exposure experiments with brine and CO₂ were performed on sandstone samples of the Stuttgart Formation representing potential reservoir rocks for CO₂ storage. The sandstone samples studied are generally fine-grained with porosities between 17 and 32% and permeabilities between 1 and 100 mD.Additional batch experiments were performed to predict the long-term behaviour of geological CO₂ storage. Reservoir rock samples were exposed over a period of several months to CO₂-saturated reservoir fluid in high-pressure vessels under in situ temperature and pressure conditions. Petrophysical parameters, porosity and the pore radius distribution were investigated before and after the experiments by NMR (Nuclear Magnetic Resonance) relaxation and mercury injection. Most of the NMR measurements of the tested samples showed a slight increase of porosity and a higher proportion of large pores.     

Localization of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) and 2,4,6-trinitrotoluene (TNT) in poplar and switchgrass plants using phosphor imager autoradiography

Phosphor imager autoradiography is a technique for rapid, sensitive analysis of the localization of xenobiotics in plant tissues. Use of this technique is relatively new to research in the field of plant science, and the potential for enhancing visualization and understanding of plant uptake and transport of xenobiotics remains largely untapped. Phosphor imager autoradiography is used to investigate the uptake and translocation of the explosives 1,3,5-trinitro-1,3,5-triazine (RDX) and 2,4,6-trinitrotoluene within Populus deltoides × nigra DN34 (poplar) and Panicum vigratum Alamo (switchgrass). In both plant types, TNT and/or TNT-metabolites remain predominantly in root tissues while RDX and/or RDX-metabolites are readily translocated to leaf tissues. Phosphor imager autoradiography is further investigated for use in semi-quantitative analysis of uptake of TNT by switchgrass.     

超高效气溶胶净化系统有效性现场检验研究

各类超高效气溶胶净化系统普遍存在的较为突出的问题是:缺乏系统工作有效性现场检测手段,难以判断系统防护是否失效。根据超高效滤料过滤特性和测试原理,并在分析了大气气溶胶对过滤效率测试影响的基础上,提出大气气溶胶背景下,基于粒数浓度测量和使用发生的高浓度单分散气溶胶作为实验气溶胶的净化系统防护有效性现场检验测试技术及系统组成,并进行了验证。     

酸雨对建筑材料的影响及防治研究综述

综合分析了酸雨对建筑外墙的涂料、石材、混凝土等主要建筑构件的腐蚀原理,并提出了防治措施,来预防酸雨对建筑材料的侵害。     

利用高炉水淬渣制作多孔吸声材料的研究

为了促进高炉炼铁水淬渣的二次利用,研究了以高炉炼铁水淬渣为原料,以硅微粉或水泥为粘结剂,采用压制成型方法制作的多孔吸声材料的吸声性能及力学性能。结果表明:用颗粒状的高炉炼铁水淬渣制作的多孔吸声材料具有良好的吸声性能,其平均吸声系数可以达到0.70以上;材料的抗压强度可以达到3.0 MPa以上。     

多孔镁铝复合氧化物对水溶液中Cr（VI）的吸附性能

摘要以镁盐、铝盐、纯碱和烧碱为原料制备了一种多孔镁铝复合氧化物（P—Mg3.1AlO4.6）,其比表面积、平均孔径和总孔容分别为206．3m2／g、8．961nm和0．4208cm3／g。研究了这种多孑L材料对水溶液中cr（VI）的吸附性能,在25～45qC时,静态吸附量为82．32～141．7mg／g;当初始浓度100mg／L、流速5mL／min、床层高度10cm和pH=6时,半穿透时间、半穿透吸附量和饱和吸附量分别为406rain、49．28ing／g和51．30Ing／g;拟合参数及误差分析表明,cr（Ⅵ）在P—M敬。AIO4.6上的静态吸附过程符合Freundlich等温方程式和伪二级动力学方程,Yoon·Nelson模型能很好地预测cr（Ⅵ）在P—Mg3.1A104.6上的动态穿透曲线。     

不同类型生物活性滤床对诺氟沙星的去除

诺氟沙星作为一种抗生素广泛应用于人类日常生活,并大量进入水体环境,给水环境质量和生态系统安全带来隐患。研究了由3种不同填料组成的水平流和复合垂直流生物活性滤床对诺氟沙星的去除效果,结果表明,在水力负荷为0．1m^3／（m^2·d）、进水诺氟沙星浓度为392．11—686．17μg／L（平均浓度为500．97μg／L）条件下,复合垂直流滤床对诺氟沙星去除效果普遍好于水平潜流滤床,以沸石为填料的复合垂直流生物活性滤床对诺氟沙星的去除效果最好,平均去除率为80．61％,说明选择合适填料和合适类型的生物活性滤床可以作为去除诺氟沙星的一种有效方法。