生物沸石滤池处理富营养化水体的挂膜实验

采用上向流生物沸石滤池处理富营养化水体,考察了挂膜阶段(前30 d)滤池对浊度、COD和TP等的去除效果,重点研究了系统中各形态氮素(NH4+-N、NO2--N、NO3--N和TN)的变化情况。结果表明,对于富营养化水体,生物沸石滤池对浊度、COD和TP的去除率分别约为80%、30%和24%;出水NH4+-N始终保持在0.5 mg/L以下,去除率在90%以上;NO2--N出现峰值(4.98 mg/L,第9 d),第13 d后即一直低于进水值;实验后期出水NO3--N与进水NH4+-N变化趋势基本一致,表明硝化生物膜已成熟,原位再生可行;生物沸石床内可能存在同步硝化反硝化现象。出水NO2-N浓度低于进水可作为生物沸石挂膜成功的一个标志。     

Effect of fatty acids and oils on photodegradation of azadirachtin‐A

Abstract

Azadirachtin‐A on exposure to UV‐light (254 nm) as a thin film on glass surface gave a isomerised (Z)‐2‐ methylbut‐2‐enoate product. Half‐life of azadirachtin‐A as thin film under UV light was found to be 48 min. Azadirachtin ‐A was irradiated along with saturated and unsaturated fatty acids, and fatty oils under ultra‐violet light as thin film. Saturated fatty acid increased the rate of photodegradation of azadirachtin‐A, whereas unsaturated fatty acids such as oleic, linoleic and elaidic acid reduced the rate of degradation. Castor, linseed and olive oil accelerated the rate of degradation, whereas neem oil showed no or little change in the rate of degradation of azadirachtin‐A. None of these fatty acids and fatty oils were effective in controlling the rate of degradation of azadirachtin‐A under UV‐light as thin film.     

Diffusion mechanism of lindane into wood charcoal

Abstract

The wood charcoal treated by 1N HNO₃ (WCT) was used to remove toxic chlorinated pesticide lindane (y‐HCH) residue from water by the sorption process. Using a simple first order reversible kinetics constants and half time equations, the film and pore diffusion coefficients were determined. Film diffusion was found to be rate limiting step in sorbing lindane by WCT. This was further authenticated by kinetics studies at different initial sorbate concentrations, different sorbent sizes, and different agitation speeds besides interruption test. A pore diffusion model was used to fit the data of kinetics in continuously mixed batch reactors (CMBR), and the tortuosity, external resistance, and surface diffusion effects on lindane sorption by WCT were noticed. The tortuosity values of 15 to 28 were obtained for WCT‐lindane system.     

Outdoor Weathering Evaluation of Carbon-Black-Filled, Biodegradable Copolyester as Substitute for Traditionally Used, Carbon-Black-Filled, Nonbiodegradable, High-Density Polyethylene Mulch Films

Carbon-black-filled, biodegradable, copolyester mulch film (Eastar®, or EA, Tennessee Eastman, Kingsport, TN) and commercial carbon-black-filled, high-density polyethylene (HDPE) mulch film were exposed for 12 weeks to commercial vegetable crop growing conditions by being placed directly on irrigated soil in the field of the University of Tennessee Alcoa Highway State Agriculture Experiment Station (Knoxville, TN) and by being placed on a plywood exposure rack as described by the American Society of Testing and Materials (ASTM) Standard Test Method 1435: Outdoor Weathering of Plastics. Mechanical properties and weather information were collected in order to evaluate the feasibility of using the newly developed biodegradable EA mulch film to replace the nonbiodegradable HDPE mulch film. Results indicate that the EA mulch film exhibited favorable tensile strength and elongation-at-break during outdoor exposure rack testing and outdoor, in-field, placed directly on the soil, exposure testing, suggesting biodegradable EA could be a substitute for the HDPE nonbiodegradable material.     

Storage stability of injection-molded starch-zein plastics under dry and humid conditions

Corn starch and zein mixtures (4 : 1 dry weight) were extruded and injection-molded in the presence of plasticizers (glycerol and water). Tensile strength and percentage elongation of the molded plastics were measured before and after 1 week of storage under a dry or humid condition (11 or 93% RH). With 10–12% glycerol and 6–8% water, injection-molded plastics had relatively good tensile properties (20- to 25-MPa tensile strength and 3.5–4.7% elongation). But while exposed to dry conditions (11% RH), the molded plastics lost weight (0.5–1.5% in 7 days) and became very brittle, with significant decreases in tensile strength and elongation. Partial replacement (5–10%) of starch with a maltodextrin (average DE 5) reduced the glass transition and melting temperatures of the starch-zein mixture as well as the dry storage stability. Using potato starch instead of corn starch significantly improved the dry storage stability of the injection-molded starch-zein plastics (18- vs 11-MPa tensile strength). Anionic corn starches with a maleate or succinate group (DS<0.01) produced injection-molded plastics with improved tensile properties and storage stability. Plastics prepared from the starch maleate and zein mixture retained the strength during 1 week of dry storage without a significant change (26-MPa tensile strength and 3.7% elongation after 1 week of storage).Paper presented at the Bio/Environmentally Degradable Polymer Society—Second National Meeting, August 19–21, 1993, Chicago, Illinois.Journal paper No. J-15561 of the Iowa Agriculture and Home Economics Experiment Station, Ames, Iowa, Project No. 2863.     

Synthesis of cellulose-fatty acid esters for use as biodegradable plastics

Long-chain fatty acid carbohydrate esters (FACE) were synthesized by the acid chloride-pyridine reaction to different degrees of substitution (DS). The hydrolyzed soybean oil was used as the source of unsaturated fatty acids. High molecular weight FACE polymers are insoluble in common solvents, such as benzene, toluene, THF, etc., and are highly water resistant. However, FACE polymers of hydrolyzed cellulose (MW 180 kD) are soluble/swellable in toluene and can be cast into tough, flexible films. FACE polymer properties of tensile strength and clasticity vary with degree of substitution and polymer size.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

废塑料生产汽柴油技术分析与应用中的误区

从废塑料生产汽柴油技术的工艺流程入手，对该项技术中存在的一些问题进行了分析，内容涉及原料来源及范围，裂化反应条件，传热与除焦，油品质量及收率，新形成的污染和经济效益评估等；指出了此项技术在应用中存在的误区。     

Effects of Starch Moisture on Properties of Wheat Starch/Poly(Lactic Acid) Blend Containing Methylenediphenyl Diisocyanate

Methylenediphenyl diisocyanate was found to improve the interfacial interaction between poly(lactic acid)(PLA) and granular starch. The objective of this research was to study the effect of starch moisture content on the interfacial interaction of an equal-weight blend of wheat starch and PLA containing 0.5% methylenediphenyl diisocyanate by weight. Starch moisture (10% to 20%) had a negative effect on the interfacial binding between starch and PLA. The tensile strength and elongation of the blend both decreased as starch moisture content increased. At 20% moisture level, the starch granules embedded in the PLA matrix were observed to be swollen, resulting in poor strength properties and high water absorption by the blend.     

论地膜污染与防治对策

随着地膜覆盖栽培年限的延长，由于残膜回收率低，土壤中残膜量逐步增加，造成地膜污染。通过分析地膜污染对环境和农作物产生的危害，对回收残膜存在的问题，总结出了防治地膜污染的对策与措施。