污水直接膜过滤用于农灌可行性试验

本试验尝试用膜直接截留污水中对人体健康有害的细菌病毒,而保留水中对作物有益的氮、磷等营养元素,以期实现水、肥双成分资源化。试验结果表明,无论是微滤膜还是超滤膜均对细菌及粪大肠菌有很高的截留率(99.9%～99.999%),污水中有机物、氮与磷的保留率分别为32%～67%、72%～78%和60%～62%。用渗滤液灌溉的小麦较之清水灌溉和常规灌溉的小麦,麦穗单重分别提高13%和7.5%。     

蜡防印花生产废水处理工程扩改设计

对蜡防印花生产废水处理工程进行扩改设计,实际结果表明:机械洗蜡废水分流后经双级气浮处理,蜡回收率和处理水回用率可达90%以上;皂化脱蜡废水分流后采用酸化-气浮处理,蜡回收率可达95%以上,出水与印花水洗废水经微电解脱色,脱色率可达85%以上;混合废水经混凝气浮-生物接触氧化-沉淀-过滤组合工艺处理,出水达标排放。该处理工艺效率高,效果稳定,经济效益和环境效益高。     

膜过滤-气相色谱法测定涂料中的苯系物、环己酮和甲苯二异氰酸酯

采用膜过滤-气相色谱法测定涂料中的苯系物、环己酮和甲苯二异氰酸酯（TD I）。用7种规格的石英毛细管色谱柱对混合标准溶液和涂料试样进行了分析实验,实验结果表明,不同属性的涂料试样添加固定量的正十四烷作内标物,经膜过滤净化后,苯系物、环己酮和TD I可采用DB-1-3或DB-1-2色谱柱同时分离并测定。测试数据经多级校准曲线处理后涂料试样中苯系物、环己酮和TD I的加标回收率为98.6%～101.8%,各组分分析结果的变异系数均小于2.0%,检出限均小于1.50×10^-5g。     

阳离子型聚合物对低温低浊水的絮凝效果与形态学特性

采用微絮凝-深床直接过滤工艺,以西安市曲江水厂低温低浊水质为原水(水温低于10 ℃,初始浊度低于10NTU),投加阳离子型聚合物(简称CP)作主混凝剂或助凝剂,借助分形数学理论与图像分析技术,对滤料粒径、原水浊度、原水温度、药剂种类、聚合物分子量及投加量、混合强度等因素对处理效果的影响进行了研究,分析探讨了不同药剂处理低温低浊水的作用机理、絮凝形态学特征以及絮体结构的分形特性.结果表明,①当温度低于4 ℃、初始浊度小于4NTU时,不宜单独采用Al2(SO4)3或PAC作为絮凝剂;当温度为4～10 ℃、初始浊度小于10NTU时,如果只投加Al2(SO4)3或PAC作为絮凝剂,宜用细砂滤料过滤;低温低浊条件下,无机混凝剂形成的絮体粒径小、结构松散脆弱、有效质量密度低、沉速慢,但表征絮体分形特性的分维值较高.②CP作絮凝剂能显著改善低温低浊水的絮凝效果与过滤性能,但混合强度需增大,宜用粗砂滤料过滤;③单独用CP作絮凝剂时,宜投加分子量较低的弱阳性聚合物或投加低剂量较高分子量的强阳性聚合物;CP用作助凝剂时,能显著减少主混凝剂用量,但宜投加强阳性聚合物或增加弱阳性聚合物的剂量.④CP兼备电性中和与吸附架桥絮凝作用,能形成粒径较大、吸附性能与过滤性能良好的网状絮体构型,其有效质量密度高,产生的污泥量少,污泥沉降速度快,脱水效果好,但分维值低.⑤各种水处理药剂的处理效果为:Al2(SO4)3(或PAC) CP＞CP＞PAC＞Al2(SO4)3,这种差别由絮体的形态学特性与构型特征各异引起.     

高锰酸盐复合剂强化饮用水除污染生产性研究

采用依时间序列进行对比的方法,考察了高锰酸盐复合剂(PPC)对饮用水源的强化除污染效能。生产性实验结果表明,PPC具有优良的强化混凝和强化过滤效能,能显著降低水厂沉后水和滤后水的浊度、COD_Mn、UV₂₅₄等水质指标。与未投加时相比较,水厂投加PPC后沉后水和滤后水浊度分别降低了25%和33.3%,沉后水和滤后水COD_Mn去除率分别提高了15.3%和11.5%,UV₂₅₄去除率分别提高了16.3%和9.5%。同时,GC/MS分析表明PPC能有效去除水源水中的多种微量有机污染物,显著提高饮用水的化学安全性。PPC通过高锰酸钾的氧化作用,水合二氧化锰的吸附作用,以及各组分间的协同强化作用,显著提高了对水中污染物质的去除效率。     

动态膜-生物反应器对化粪池废水的处理

应用动态膜原理,以0.1mm孔径的普通筛绢代替固定膜材料构成一体式动态膜-生物反应器(DMBR)处理实际化粪池污水。HRT=5h,膜通量J=18L/(m2·h)。动态膜生物反应器对COD和NH4+-N的平均去除率分别达到了65.3%和68.2%,同时还对动态膜的通透性进行了研究。     

固定化生物活性炭纤维处理洗浴废水的研究

采用混凝-砂滤-固定化生物活性炭纤维的组合处理工艺来处理洗浴废水.利用聚合氯化铝和聚丙烯酰胺为混凝剂对废水进行混凝处理,之后将废水通入砂滤柱,废水在曝气池进行曝气后进入固定化生物活性炭纤维(IBACF)单元.IBACF固定化完成后,连续运行30 d,去除率稳定之后,处理后的浊度、LAS、S0D_(Mn)平均值分别为2.2NTU、0.12 mg·L~(-1)、2.33 mg·L~(-1),平均去除率分别为95.2%、94.7%、84.8%.经处理后的洗浴废水各项指标均可以达到生活饮用水卫生标准或城市供水水质标准,可以直接回用于洗浴用水和其他生活杂用水.     

Transformations of particles, metal elements and natural organic matter in different water treatment processes

Characterizing natural organic matter （NOM）, particles and elements in different water treatment processes can give a useful information to optimize water treatment operations. In this article, transformations of particles, metal elements and NOM in a pilot-scale water treatment plant were investigated by laser light granularity system, particle counter, glass-fiber membrane filtration, inductively coupled plasma-optical emission spectroscopy, ultra filtration and resin absorbents fractionation. The results showed that particles, NOM and trihalomethane formation precursors were removed synergistically by sequential treatment of different processes. Preozonation markedly changed the polarity and molecular weight of NOM, and it could be conducive to the following coagulation process through destabilizing particles and colloids; mid-ozonation enhanced the subsequent granular activated carbon （GAC） filtration process by decreasing molecular weight of organic matters. Coagulation-flotation and GAC were more efficient in removing fixed suspended solids and larger particles; while sand-filtration was more efficient in removing volatile suspended solids and smaller particles. Flotation performed better than sedimentation in terms of particle and NOM removal. The type of coagulant could greatly affect the performance of coagulation-flotation. Pre-hydrolyzed composite coagulant （HPAC） was superior to FeCl3 concerning the removals of hydrophobic dissolved organic carbon and volatile suspended solids. The leakages of flocs from sand-filtration and microorganisms from GAC should be mitigated to ensure the reliability of the whole treatment system.     

Improvement of the antifouling characteristics in a bioreactor of polypropylene microporous membrane by the adsorption of Tween 20

Surface modification by physical adsorption of Tween 20 was accomplished on polypropylene microporous membranes (PPMMs). Attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FT-IR) and scanning electron microscope (SEM) were used to characterize the chemical and morphological changes on the membrane surfaces. Water contact angles and relative pure water fluxes were measured. The data showed that the hydrophilic performance for the modified membranes increased with the increase in the adsorption amount of Tween 20 onto the surface or into the pores of polypropylene microporous membranes. To test the antifouling property of the membranes by the adsorption of Tween 20 in a membrane bioreactor (MBR), filtration for active sludge was performed using synthetic wastewater. With the help of the data of water fluxes and the FE-SEM photos of the modified PPMMs before or after operating in a MBR for about 12 d, the PPMMs with monolayer adsorption of Tween 20 showed higher remained flux and stronger antifouling ability than unmodified membrane and other modification membranes studied.     

膜的改性及其在环境领域应用研究进展

膜改性由于具有清洁、廉价、节能等特点,近年来得到快速发展,是解决膜污染的有效方法之一。本文综合介绍了膜的基体改性、表面改性这两种改性类型和目前常用的改性方法包括表面涂覆、表面活性剂改性、化学修饰改性、仿生改性等等,并简单介绍了膜改性在环境领域的应用,探讨了膜改性今后的发展。