A numerical study on the effects of EGR and spark timing to combustion characteristics and NOx emission of a GDI engine

EGR is one of the most significant strategies for reducing especially nitrogen oxides (NO_x) emissions from internal combustion engines. The thermal efficiency of spark ignition engines is lower than compression ignition engines because of its lower compression ratio. If the compression ratio is increased to obtain higher thermal efficiency, there may be a knocking tendency in spark ignition engines. EGR can be used in order to reduce NO_x emissions and avoid knocking phenomena at higher compression ratios. In-cylinder temperature at the end of combustion is decreased and heat capacity of fresh charge is increased when EGR applied. Besides EGR, spark timing is another significant parameter for reducing exhaust emissions such as nitrogen oxides, and unburned hydrocarbon (UHC). In this study the effects of EGR and spark timing on spark ignition engine were investigated numerically. KIVA codes were used in order to model combustion process. The combustion process has been modeled for a single cylinder, four stroke and gasoline direct injection (GDI) spark ignition engine. The results showed that in-cylinder pressure and heat release rate decrease as EGR ratio increase. In-cylinder pressure increases with the advancing of spark timing. Advancing spark timing increases the heat release rate and in-cylinder temperature. The simulation results also showed that EGR reduced exhaust gas temperature and NO_x emissions.     

An experimental apparatus for testing biodiesels based on a CFR engine—setup and validation with different methyl ester blends

A cooperative fuel research (CFR) engine was modified and instrumented in order to control operating conditions and to measure engine parameters and in-cylinder pressure diagrams. Aiming at the comparison of different alternative fuels, an experimental procedure was defined, including cetane number (CN) evaluation and the definition of engine operating quantities in different working points, for fixed levels of compression ratio (CR) and injection advance. An investigation was made considering several blends of methyl-esters of rapeseed oil (RME) and of a mix of vegetable oils (VOME) with conventional diesel oil. The defined experimental procedure was applied to assess CN, engine brake thermal efficiency (bte) and exhaust emissions. Results show that the biodiesel content has a positive influence on soot emissions, with strong reduction, while thermal efficiency and NO_X emissions are negatively affected, which can be justified taking into account fuel properties and changes in combustion process. As observed outcomes are generally in line with those presented in literature, the facility proved to be a suitable tool for basic investigations on alternative fuels to be used in specific applications.     

家庭部门生活能源消费碳排放:测度与驱动因素研究

本文运用IPCC的二氧化碳排放量测算方法,在省际层面测度了我国家庭部门直接能源消费碳排放,并基于扩展的STIRPAT和Kaya模型,构建家庭部门直接能源消费碳排放影响因子动态面板数据模型,对我国2003-2012年分省面板数据样本及城乡子样本进行系统GMM估计。本文研究表明,第一,我国城乡家庭部门碳排放总量和人均碳排放在近十年都呈快速上升趋势,家庭部门碳排放的空间分布具有明显的地域差异特征,高碳排放地区主要集中在东、中部地区,西部地区的碳排放水平较低;第二,城乡家庭部门生活能源消费的上期碳排放量对本期碳排放产生重要的正向影响,这反映出我国家庭部门碳排放具有显著的惯性特征和路径依赖性,是一种动态自适应机制;人口规模、居民消费水平、能源消费结构、碳排放强度、能源消费强度和城镇化因素,都对我国居民能源消费碳排放总量及人均碳排放具有显著的影响,城乡之间的家庭能源消费碳排放驱动因素存在差异。本文研究得到如下启示及政策含义:家庭部门碳减排将是一个有步骤、分区域的渐进过程,我国碳减排政策应当兼顾消费升级和碳排放的双重目标,努力构建分层次碳减排的适应性预期机制。具体而言,一方面应着眼于引导和激励居民低碳消费,缓解人口规模增加、消费水平提升和城镇化对家庭部门碳减排的压力;另一方面要通过能源价格改革、财政政策和环境规制政策等优化我国能源消费结构,不断降低煤炭消费比重,提高清洁能源的消费。同时,通过技术创新、设备改造等科技手段提高煤炭利用效率,降低碳排放强度,这些政策将更有利于城镇家庭部门碳减排。     

产朊假丝酵母处理马铃薯淀粉废水

研究了pH、接种量、无机盐(通过加入磷酸二氢钾进行无机盐补充)及DO等对产朊假丝酵母处理马铃薯淀粉废水的影响.结果表明.在pH为5.0、产朊假丝酵母接种量为10%(体积分数)、磷酸二氢钾(质量分散为0.1%)加入量为0.5 g/L、废水不灭菌的条件下,废水处理效果和产朊假丝酵母生长最佳.且当废水COD为5 074 mg/L时,COD去除率达到74.86%,同时可获得2.23g/L的单细胞蛋白.产朊假丝酵母处理马铃薯淀粉废水的最佳条件的实验研究对实现马铃薯淀粉废水资源化利用提供了理论参考.     

模拟车用工况下5kW燃料电池尾气净化系统

模拟了车用工况下燃料电池发动机脉冲式排氢的特点,设计开发了一套质子交换膜燃料电池的尾气净化系统,并以5 kW燃料电池的尾气排放为例,研究其净化效果。研究了电池阳极排放氢气缓冲前后尾气中氢气浓度的变化,以及不同空速条件下氢气的去除效果。结果表明：电堆阳极排放氢气经过缓冲处理后,尾气中氢气浓度趋于平稳,大部分工况下处在2%以下,达到了安全处理的要求;尾气中氢气的去除效果与空速密切相关。对自制的整体式催化剂而言,当空速低于20000 h^-1时,氢气的去除率能达到约95%,而当空速达到39270 h^-1时,氢气的去除率仅为10.9%。鉴于这一问题,提出通过采用尾排空气的分流手段调整催化燃烧反应器对空速的要求,以提高尾气中氢气的去除率。     

强化生物通风修复过程中柴油衰减规律及其影响因素研究

强化生物通风技术对于修复因地下储油罐泄漏引起的土壤污染具有很大的应用前景。通过室内土柱模拟柴油泄漏污染土壤,从土柱中总石油烃（total petroleum hydrocarbon,TPH）剖面分布随时间的变化及降解模式角度,分析了其自然衰减和强化生物通风过程。结果表明：初始柴油浓度直接影响着各柱在自然衰减和强化生物通风过程中柱内的残余TPH平衡分布曲线的形状和浓度峰值位置;在前期自然衰减过程中（约1个月）,当土壤中的柴油浓度为5 000～40 000 mg油/kg土时,整个柱内TPH变化的主要原因是重力扩散迁移的结果;当土壤中的柴油浓度≤5 000 mg油/kg土时,其TPH的变化不仅是重力扩散迁移作用的结果,生物降解作用也存在;通风约2个月后,抽提作用对于保持土柱上部柴油浓度稳定变化的意义较为突出。     

应用CALINE4模式估算机动车排放污染物的浓度——以济南市主干道为例

随着经济的快速发展,机动车排气污染已成为我国城市空气污染的重要来源,而且在一定时段,机动车排气污染已成为空气污染最主要的污染源之一。以济南市经十路为例,采用实地调查的方法,得出各时段的车流量,选用大气环评助手EIAA中的CALINE4模式对机动车尾气中的主要污染物CO、NOx、THC的排放浓度进行估算,得出3种污染物CO、NOx、THC最大值均出现在7:00—8:00之间,最小值均出现在12:00-13:00之间,排放强度由大到小为:CO、THC、NOx。     

用电解锰阳极泥和含SO_2工业尾气制备硫酸锰

以电解锰阳极泥与电解锌生产中产生的含SO_2尾气为原料,经过反应、浸出、浸出液两次净化和浓缩结晶制备硫酸锰,考察了反应时间、含SO_2尾气的流量及反应温度对Mn~(4+)转化率的影响.实验结果表明:在反应时间45 min、反应温度20～30 ℃、含SO_2尾气流量16 L/min的条件下,Mn~(4+)转化率达90%以上;尾气中SO_2利用率随尾气流量增加而降低;所得MnSO_4·H_2O产品质量达到GB1622-86<工业级硫酸锰标准>.     

Experimental study of recycling lightweight concrete with aggregates containing expanded glass

The focus is on the issue of waste management when constructing and recycling lightweight concrete (LWC) with aggregates containing expanded glass. The paper analyses the recycling of concrete from lightweight aggregates, and on the important issue of environmental and waste management. The characteristics of recycling LWC such as density, compressive strength and thermal conductivity are investigated, and compared with normal existing concrete from lightweight aggregates. The results indicate that it is possible to recycle lightweight concrete construction waste. The described method shows great possibilities for increasing the use of construction waste materials from LWC containing expanded glass, in order to benefit from better use of the available capacity from existing construction waste. The characteristics of density, compressive strength and thermal conductivity from the new recycled material were compared with normal existing concrete from lightweight aggregates, such as changes in dependency on the type and parts of waste as well as its new binding components. Thus, a new recycled material has been created with new characteristics of density, compressive strength and thermal conductivity, which is conform to the compressive strength class and rules on heat protection and energy efficiency use in buildings (SI OJ RS No. 42/2002). Laboratory density, compressive strength, and thermal conductivity tests results showed that LWC can be produced by the use of waste LWC with aggregates containing expanded glass. However, the use of waste LWC with aggregates containing expanded glass seems to be necessary for the production of cheaper and environmentally friendly LWC.     

Physical Modeling of Emissions from Naturally Ventilated Underground Parking Garages

The dispersion of pollutants from naturally ventilated underground parking garages has been studied in a boundary layer wind tunnel. Two idealized model setups have been analysed, one was simulating pollutant dispersion around an isolated rectangular building and one was representing dispersion in a finite array of idealized building blocks. Flow and dispersion close to modelled ground level emission sources was measured. The results illustrate the complexity of the flow around buildings and provide insight in pollutant transport from ground level sources located directly on building surfaces. As a result, areas critical with respect to high pollutant concentrations could be visualized. Particularly, the results show high concentration gradients on the surface of the buildings equipped with modelled emission sources. Inside the boundary layers on the building walls, a significant amount of pollutants is transported to upwind locations on the surface of the building. The paper documents the potential of physical modelling to be used for the simulation and measurement of dispersion close to emission sources and within complex building arrangements.