杭州市灰霾与非灰霾日不同粒径大气颗粒物来源解析

在2011年典型灰霾和非灰霾天气下,采集了杭州市不同粒径的大气颗粒物样品,测定并分析各粒径段颗粒物的质量浓度及其化学成分;同时采集并分析了主要污染源排放的颗粒物样品,通过CMB(化学质量平衡)模型进行源解析. 结果表明:灰霾天气下,二次粒子是杭州市各粒径段颗粒物的首要贡献源,其对≤1.1、>1.1~3.3、>3.3~5.8和>5.8~10μm粒径段的颗粒物贡献率分别为60.4%、62.2%、54.8%和46.5%. 在一次排放源中,机动车尾气是≤1.1和>1.1~3.3μm粒径段颗粒物的重要来源,贡献率分别为13.8%和12.2%;城市扬尘是>3.3~5.8μm粒径段颗粒物的重要来源,贡献率达到16.0%;而建筑施工尘是>5.8~10μm粒径段颗粒物的重要来源,贡献率为14.2%. 非灰霾天气下,随着颗粒物粒径的增加,二次粒子的贡献率显著下降,对≤1.1μm粒径段颗粒物的贡献率为42.7%,而对>5.8~10μm粒径段颗粒物的贡献率仅为15.5%;机动车是各粒径段颗粒物的重要贡献源,贡献率均在20%以上;煤烟尘是≤3.3μm细粒径段颗粒物的重要贡献源类,贡献率为22.0%;城市扬尘是>3.3~5.8μm粒径段颗粒物的重要来源,贡献率为18.3%;建筑施工尘依然是>5.8~10μm粒径段颗粒物的重要来源,贡献率为21.4%.      

FBC-DPF在柴油机颗粒物控制中的应用研究

目前针对加装FBC-DPF(燃油添加剂-柴油机颗粒捕集器)后的柴油机放特性研究较少,并且缺乏FBC-DPF对颗粒物中PAHs排放量的影响效果研究. 为全面评估加装FBC-DPF后柴油机颗粒物排放特性和FBC-DPF对柴油机尾气中的颗粒物排放污染控制效果,在发动机台架上对装有FBC-DPF的重型柴油机进行了颗粒物排放特性试验. 利用电子低压撞击仪(ELPI)测量加装FBC-DPF前、后柴油机颗粒物的数浓度与粒径分布,用玻璃纤维滤膜采集加装FBC-DPF前、后尾气中的固相PAHs,利用色谱质谱联用仪对加装FBC-DPF前、后尾气中的固相PAHs进行定量分析. 结果表明:①加装FBC-DPF后柴油机排放的颗粒物数浓度大幅降低,FBC-DPF对尾气中颗粒物的捕集效率平均值在95%左右;②加装FBC-DPF后柴油机固相PAHs总比排放量有所降低,在大负荷区域降幅在25.0%~88.0%之间;③加装FBC-DPF前的颗粒物中位直径为30~89nm,而加装FBC-DPF后的颗粒物中位直径为41~98nm,平均增幅为38.2%. 对于国Ⅳ及未来国Ⅴ柴油机排放法规,FBC-DPF是解决柴油机颗粒物排放的有效手段;此外,FBC-DPF可以大幅降低柴油机尾气中的有毒成分,并且能够适应高含硫量的燃油环境.      

园林植物滞留不同粒径大气颗粒物的特征及规律

为研究常用园林植物滞留大气颗粒物的能力,本文以北京市常用园林植物为例,应用直接采样、电镜分析和统计分析的方法,对选定园林植物滞留不同粒径大气颗粒物的特征及规律进行了系统分析。结果表明：（1）园林植物滞留的颗粒物形状为不规则块体、球体和聚合体,通过对比分析得出,滞留大气颗粒物能力由高到低的微形态结构依次是蜡质结构〉绒毛〉沟槽〉条状突起,并且这些微形态结构越密集、深浅差别越大,越有利于滞留大气颗粒物。（2）以园林植物叶片滞留颗粒物的数量进行统计时,得出园林植物叶片表面大部分为PM10（Dp≤10μm）,均在98%以上,而PM2.5（Dp≤2.5μm）均在90%以上,粗颗粒物（Dp〉10μm）的数量对总体数量的贡献非常小,均在2%以下;以体积进行统计时,得出PM10的体积在总体积中的比例在50%以上,对颗粒物总体积贡献最大,滞留的PM2.5体积占总体积8.5%-17.6%,粗颗粒物（Dp〉10μm）体积占总体积20%以上。（3）对园林植物滞留颗粒物累积规律分析得出：在相同观测叶面积下,园林植物滞尘10 d的叶表面颗粒物数量较滞尘5 d的叶表面颗粒物数量均有所增加,增幅最大的是小叶黄杨（Buxus microphylla）,增幅最小的是月季（Rosa chinensis）,通过方差分析得出绦柳（Salix matsudana f.pendula）叶表面颗粒物数量显著低于除银杏（Ginkgo biloba）之外的其它7种树种,大叶黄杨（Euonymus japonicus）、小叶黄杨和国槐（ Sophora japonica）叶表面滞留颗粒物的数量较多,并且显著高于月季、银杏和绦柳叶表面滞留的颗粒物数量;滞尘10 d后园林植物叶表面滞留的颗粒物的总面积均未超过观测叶面积的25%,至于叶片持续滞留颗粒物多少天后达到饱和状态仍需进一步研究。     

老化过程中铜形态变化的X射线吸收精细结构谱的(XAFS)初步研究

利用X射线吸收精细结构谱(XAFS)对老化过程中土壤中铜的分子形态进行初步表征。以硫酸铜、氧化铜和硫化铜的X射线吸收扩展边结构(EXAFS)谱为参比,对土壤样品中Cu的EXAFS谱进行拟合,得到不同老化阶段与参比物质相对应的结合态Cu的百分含量,并与连续提取法表征进行比较。XAFS分析结果表明,老化阶段土壤样品中铜的主要结合形态是CuSO_4,同时还有部分CuS,基本不含有CuO。随着时间的推移,土壤中CuSO_4百分含量呈现出下降的趋势,CuS百分含量呈现出上升的趋势。这与连续提取法研究结果中其可交换态的百分比下降,残渣态上升的趋势相似。     

北京市2009年8月大气颗粒物污染特征

为研究2008年8月北京奥运会1a之后北京市大气颗粒物的污染特征,于2009年8月对北京市大气颗粒物PM10、PM2.5样品进行采集,测量其质量浓度并对其中的水溶性离子组分进行分析.研究发现2009年8月北京市大气颗粒物PM10、PM2.5质量浓度日均值分别为176.9μg/m3和102.5μg/m3.PM10质量浓度比2008年观测值上升了180%,比2007年降低了10%; PM2.5质量浓度比2008年观测值上升了126%,比2007年上升了31%.水溶性离子是大气颗粒物的重要组分,分别占PM10和PM2.5质量浓度的43%和61%.对比发现,污染天气条件下PM2.5/PM10和NO3-/SO42-比值升高,移动源是北京地区主要的污染物来源.风向风速和降水等天气条件对颗粒物质量浓度有很大影响,其中0.5~1.0m/s的东南风条件下大气颗粒物污染最为严重.     

上海城区典型空气污染过程中细颗粒污染特征研究

采集了上海城区2009年10月10~21日期间2次空气污染过程的样品,在对污染过程分析的基础上,着重分析了PM2.5及其化学组分的变化,探讨了污染源及形成机制.研究表明,14日的灰霾过程主要由本地排放的污染物二次转化形成,PM2.5占PM10比重超过60%且PM2.5中离子组分含量高.17~19日的浮尘过程中,受北方沙尘影响本市粗颗粒浓度上升,PM2.5所占比重下降,二次离子组分从细颗粒物向粗颗粒物转移且Ca2+浓度上升,同时受到长江三角洲区域秸秆焚烧的影响,细颗粒物中K+, EC和OC含量高.因此,应在控制本地源排放的同时,加强对细颗粒尤其是二次细颗粒污染及其前体物的协同控制.     

Dissolution behavior of metals from particulate matter emissions

Exposure to air particulate matter (PM) is linked to numerous health effects. In order to improve the understanding of the role of its metallic components, their solubility was examined by using serial short-contact dissolutions totalling 1?h and additional sequential contact periods of 1, 4, and 8 days. The dissolution experiments were performed in solutions containing the main biological electrolytes. ICPMS determinations were used to quantify the dissolved metals. The total compositions were determined after closed vessel microwave digestion. Large variations in the rate and completeness of the dissolutions were observed. Fast and extensive dissolutions within the short-contact time (e.g., Zn, Cd) as well as slow dissolutions persisting during the last contact period (e.g., Ni, Cu, Sb, Pb) were found for smelting emissions. The multi-element determinations also made it possible to identify relationships between dissolution of different metals and define gradual composition changes of residual PM. When comparing with dissolutions performed in de-ionized water, similar major fractions were observed at short-contact time for minor components of smelting or combustion emissions (e.g., V, Ni, Cd), suggesting a preponderance of easily available forms at the surface of the relatively inert particle cores. The use of these time sequential methods may help in (1) modeling metal partitioning in biological media and (2) investigating the causes of adverse effects attributed to air PM.     

Indoor and outdoor air pollution and lung cancer in New Hampshire and Vermont

Indoor and outdoor air pollution is known to contribute to increased lung cancer incidence. This study is the first to address the contribution of home heating fuel and geographical course particulate matter (PM₁₀) concentrations to lung cancer rates in New Hampshire, USA. First, Pearson correlation analysis and geographically weighted regression were used to investigate spatial relationships between outdoor PM₁₀ and lung cancer rates. While the aforementioned analyses did not indicate a significant contribution of PM₁₀ to lung cancer in the state, there was a trend towards a significant association in the northern and southwestern regions of the state. Second, case-control data were used to estimate the contributions of indoor pollution and secondhand smoke to the risk of lung cancer with adjustment for confounders. Increased risk was found among those who used wood or coal to heat their homes for more than 10 winters before the age of 18, with a significant increase in risk per winter. Resulting data suggest that further investigation of the relationship between heating-related air pollution levels and lung cancer risk is needed.     

Characterization of airborne particulate matter in Thessaloniki,Greece

A receptor modeling approach has been applied to identify and apportion sources of airborne particulate matter in Thessaloniki, Greece. The absolute principal component analysis source apportionment technique used, provided quantitative information regarding both source particle characteristics and impacts. The analysis identified four major sources of heavy metals within total suspended particles (TSP) in the centre of the city: oil burning, pyrometallurgical non‐ferrous metal processes, motor vehicles and soil resuspension. Their contributions to TSP estimated by regression on absolute principal component scores (APCS) were 12%, 8%, 5% and 4%, respectively. A similar analysis conducted for a sampling site close to the industrial area identified five major sources: oil burning, industrial Cr source, soil resuspension, pyrometallurgical non‐ferrous metal processes and motor vehicles with contributions 20%, 15%, 9%, 8% and 4%, respectively.     

超细水雾抑制煤燃烧的模拟实验研究

为了研究超细水雾对煤燃烧的抑制效果,基于小尺寸空间抑制燃烧实验平台,研究了超细水雾对煤燃烧的抑制效果,计算在超细水雾作用下实验空间内部氧气、二氧化碳、一氧化碳体积分数的变化情况以及燃烧空间内不同部位的温度变化情况,并且与煤自由燃烧的情况做对比。研究表明超细水雾对煤燃烧的火灾发展过程有很好的抑制作用。研究结论对超细水雾应用于熄灭矿井煤炭火灾具有一定的指导意义